HOBERG 5908337 Waterproof Parasol Rotates 360º Instructions

FLEXIBLER
SONNENSCHIRM
Instructions for use

Dear Customer,
We are delighted that you have chosen our Hoberg flexible sun shade. If you have any questions about the product, please contact our customer service department via the website: www.hoberg-shop.de 

Symbols

| Danger symbol: This symbol indicates the dangers of injury. Read through the associated safety notices carefully and follow them.
---|---
| Supplementary information
| Hand wash
| Do not bleach
| Do not dry in a tumble dryer
| Do not iron
| Do not treat with solvents

Intended Use

• The product is used to provide privacy and protection from the sun on a balcony or patio.
• The product is not suitable for protecting against extreme weather conditions (storms,  hail, etc.).
• The product is not a toy!
• The product is for personal use only and is not intended for commercial applications.

Use the product only as described in the instructions for use.
Any other use is deemed to be improper.

Safety Notices

• Keep children and animals away from films and plastic bags. There is a danger of suffocation!
• Only set up the shade out of the reach of naked flames and heaters. Ensure that the sun shade is placed firmly and securely in a suitable holder for sun shades.
• Make sure that there are no people or objects in the area of movement when the shade is being opened out.
• Remember to also use other sun protection (UVproof clothing, sunscreen with SPF, etc.).
• Do not leave the opened shade unattended.
• Take down the shade cover in a breeze or if squalls are approaching because the shade only has a limited level of wind safety.
• Do not allow the product to fl utter in the wind because otherwise the product could be damaged.
• Protect the product from frost and impacts.
• Do not use any corrosive or abrasive cleaning agents to clean the product! They could damage the surface.

Items Supplied
Check the items supplied for completeness and the components for possible transport damage. If you find any damage, do not use the product but contact our customer service department.
Remove any possible films, stickers, or transport protection from the product.
1 x shade cover with two rods inserted
2 x cross brace with holder for shade cover
1 x tube with a locking screw for adjusting the height
1 x rod with joint for aligning the shade cover
1 x instructions for use

Assembly

1. Plug the tube with a locking screw into an umbrella stand or similar holder (not supplied with the product).
2. Slide the rod with the joint into the tube with the locking screw and fix the rod with the locking screw of the tube.
3. Guide one cross brace through the joint for aligning the shade cover so that the end without the holder sticks out. Then plug the other cross brace onto the end.
4. Move the assembled cross braces so that the connection point is within the joint and fix this in place using the outer locking screw. When you do this, make sure that both holders are pointing in the same direction.
5. Press the rods in the shade cover into the holders of the cross braces. They must engage.
6. Place the sun shade in the location you want and if necessary adjust the height and alignment of the shade again (see next chapter).

As the shade cover is under tension, we recommend that to take it apart you pull the rods of the shade cover out of the holder and the fabric at the side. The rods can then be reattached to the shade cover with the hook-and-loop fastener.

Adjusting the Shade

• To adjust the height, undo the locking screw on the tube, pull the rod to the length you want, and fix it again with the locking screw.
• To adjust the tilt angle of the short side, undo the bottom locking screw on the joint, tilt the shade cover into the position you want, and fix it again.
• To adjust the tilt angle of the long side, undo the top locking screw on the joint, rotate the shade cover into the position you want, and fi x it again.

Cleaning and Storage

• The rods can be removed from the shade cover to make it easier to clean. To do this, open the hook-and-loop fastener and pull the rod out of the tunnel.
• The shade cover is hand-washable. Do not clean the washing machine. Do not use fabric softener or any corrosive or abrasive cleaning agents.
• Open up the shade cover while it is still wet and allow it to dry in the air. Do not dry in a tumble dryer or with a hair dryer.
• When the shade is not in use, store it in a dry place that is out of the reach of children and animals.

Product Data

Article number:| 08828 (grey), 01456 (terracotta), 01719 (beige), 01886 (brown)
---|---
Dimensions of shade cover:| approx. 130 x 180 cm
Ø of telescopic rod:| approx. 22 / 25 mm
Length of telescopic rod:| approx. 120 – 200 cm
UV protection:| 50
The ID of instructions:| Z 08828_01456_01719_01886 M HO V2 1021 DK

Disposal
**** Dispose of the packaging material in an environmentally friendly manner so that it can be recycled.
If the product can no longer be used, it should also be disposed of in an environmentally friendly way.
All rights reserved.

Customer Service / Importer
DS Produkte GmbH
Am Heisterbusch 1
19258 Gallin
Deutschland
Tel.: +49 38851 314650
Calls to German landlines are subject to your provider’s charges.www.hoberg- shop.de

References

• Hoberg - Your Project Partner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>