B G 22049466 Extenda-Ban Valve User Manual
- June 3, 2024
- B G
Table of Contents
B G 22049466 Extenda-Ban Valve
DESCRIPTION
The Extenda-Ban valve is a brass heavy-duty corrosion-resistant valve with a non-drip tip (tip shut off) tip suitable for indoor or outdoor liquid applications. It is used on several of the B&G sprayers, including models of the Primeline and AccuSpray Elite. Please refer to the User Manual for your sprayer, this addendum only provides information on the valve and associated nozzles and is designed to supplement the User Manual of the sprayer.
EXTENSIONS
Several extensions are available for the Extenda-Ban in brass and stainless
steel to extend the distance between the valve and the nozzle to 9” (23 cm),
18” (46 cm), and 24” (61 cm) (see part numbers in the Extenda-Ban parts list
below).
NOZZLES & TIP ASSEMBLIES
B &G 4-WAY CRACK & CREVICE TIP ASSEMBLY #22049466 / 1608003819
Tip
|
Flow Rate
| |
Image
---|---|---|---
| oz/min| ml/min|
50° Narrow/Coarse Fan| 14.1| 417.0
80° Wide/Fine Fan| 6.4| 189.3
Large Pin Stream| 8.9| 263.2
Tips that Are Inserted into Crack & Crevice Orifice
1” (2.5 cm) Red Crack & Crevice Straw 6 oz/min (177.4 ml/min)|
6” (15 cm) Crack & Crevice White Straw 3.8 oz/min (112.4 ml/min)|
3.5” (9 cm) Stainless Steel Injector Needle|
2” (5 cm) Stainless Steel Void Tip|
4” (10 cm) Stainless Steel 4-Way Void Tip|
B &G 4-WAY TIP ASSEMBLY #22049451/1608003816
Tip
|
Flow Rate
| |
Image
---|---|---|---
| oz/min| ml/min|
50° Narrow/Coarse Fan| 14.1| 417.0
80° Wide/Fine Fan| 6.4| 189.3
Large Pin Stream| 8.9| 263.2
Small Pin Stream| 4.5| 133.16
ADJUSTABLE PIN-TO-CONE #23083602/1608003917.
MAINTENANCE AND REPAIR
- Detach the valve and extension from the hose. Carefully remove the mesh strainer. Squeeze the trigger to drain all liquid from the valve.
- Remove the trigger (1), then the snap ring (5), the safety lock nut (6), the adjustment screw (4), the lock nut (3), and then the packing nut (2). The trigger can be removed by moving it to the back of the valve.
- Unscrew the extension at the front of the valve. The extension can be pulled away from the valve along with the interior steel cable.
- Packing washers (white) that were at the end of the cable will remain inside the valve. Carefully dislodge and remove these washers.
- Remove the tip and nozzle assembly from the end of the extension, be careful to keep the soft seat gasket. Use 2 wrenches to loosen the tip: one to hold the extension, and a second to loosen the tip. Note: the extension may become twisted and unusable unless 2 wrenches are used to remove the tip. Inspect the soft seat gasket and the small O-ring on multijet tips, and replace if damaged or worn. Replace the nozzle if it is more than 2 years old.
- Push the cable out the front of the extension to expose the spring, the small lock nut, and the seat stem. Unscrew the seat stem and lock nut, and slide off the spring. Place these small pieces in a closed container (they are easily misplaced).
- Remove the stainless steel cable by pulling it slowly through the back end of the extension – you cannot pull the cable through the front of the extension. The threaded end of the cable at the nozzle end is short and easily passes through the curve in the extension. The end of the cable at the valve end is long and will not pass through the curve.
- Replace the cable if it is worn or damaged.
- Re-assemble the extension by inserting the short end of the cable into the back so that threads are exposed at the nozzle end.
- Slide the spring onto the end of the cable, then the seat stem lock nut. Screw the lock nut to leave about 4 threads at the base of the end of the cable.
- Attach the seat stem to the cable, in front of the lock nut. Hand tightens the seat stem against the lock nut.
- Insert the long end of the cable into the front end of the valve. Push the cable through the valve until the end is through the back of the valve. Tighten extension to the valve body.
- Insert 2 or 3 packing washers onto the cable, then slide on the packing nut behind the washers and tighten.
- Valves built before 1999 have a stainless steel packing nut that takes 3/8 wrench, there is no internal O-ring, these valves need 3 washers.
- Valves built between 1999 and 2000 have a brass packing nut + O-ring, this nut takes a 7/16 wrench, these valves need 2 washers
- Valves built after 2000 have a stainless steel packing nut + O-ring, this nut takes a 3/8 wrench, and these valves require 3 washers.
- Screw onto the cable the lock nut and the adjustment screw. Turn the adjustment screw so the end of the cable is level to the top of the slot in the top of the screw.
- Tighten the lock nut against the screw.
- Attach the valve trigger by inserting it into the space between the lock nut and adjustment screw, then insert the trigger screw.
- Screw the safety lock nut into the valve body, and then attach the snap ring.
- Attach the tip and nozzle to the end of the extension, and make certain the soft seat gasket is facing correctly. The small end faces the extension. Press the trigger to retract the seat stem into the extension, then attach the tip and nozzle.
EXTENDA-BAN VALVE PARTS
Number
|
Part #
|
Description
|
Order Number (US)
|
Order Number (EU)
---|---|---|---|---
24| 120| Extenda-Ban Valve 9″ (Less Tip)| 22042101| 1608003714
220| Extenda-Ban Valve 18″ (Less Tip)| 22042203| 1608003717
420| Extenda-Ban Valve 24″ (Less Tip)| 22042778| 1608003733
25| VB-147| Valve Body Kit| 22044450| 1208001188
26| VT-140| Trigger, Valve Housing, Screw| 22042800| 1108004814
26B| VT-140| Trigger Screw, Screw Housing| 1208004903| 1208004903
30| PN-150-2| Packing Nut (2001-Present)| 22042455| 1208001187
30A| PN-150-1| Packing Nut (1999-2000)| 22042454| 1608003726
31| VP-151| Packing Valve| 22045099| 1608003747
32| PN-150| Packing Nut (Prior to 1999)| 22044900| 1608003746
34| AS-148| Adjusting Screw, Lock Nut, Snap Ring| 22044500| 1108004817
36| SL-162| Safety Lock Nut| 22046700| 1608003785
37| MS-145-50| 50 Mesh Strainer and Strainer Support| 22043800| 1108004815
39| NG-146| Nylon Gasket| 22044200| 1608003739
40| SA-143| Strainer Housing| 22043400| 1608003736
41| VC-152| Valve Cable 9″| 22045300| 1208001192
VC-153| Valve Cable 18″| 22045400| 1208001193
VC-163| Valve Cable 24″| 22045450| 1208001195
42| VE-154| Brass Extension 9″| 22045500| 1608003751
VE-155| Brass Extension 18″| 22045600| 1608003753
VE-164| Brass Extension 24″| 22045650| 1608003755
VE-154-SS| Stainless Steel Extension 9″| 22045510| 1608003752
VE-155-SS| Stainless Steel Extension 18″| 22045610| 1608003754
VE-164-SS| Stainless Steel Extension 24″| 22045710| 1608003758
Number| Part #| Description| Order Number (US)| Order Number (EU)
---|---|---|---|---
43| VS-156| Seat Stem Spring| 22045700| 1608003757
44| SSL-157| Stainless Steel Hex Nut| 22045901| 1208001197
45| SS-158| Seat Stem| 22046100| 1608003782
46| SP-159| Soft Seat Gasket| 22046300| 1208001198
47
| 5850-CC| B&G 4 Way C&C Tip Assembly (Parts 48-51)| 22049466| 1608003819
5850| Tip Assembly (No C&C)| 22049451| 1608003816
48| 9751-M| Holder, B&G 4 Way Modified Assembly| 22049300| 1608003813
49| 4190| Viton Gasket®| 22034700| 1608003674
50
| 5800-CC| B&G 4-Way C&C Tip| 22049467| 1608003820
5800| B&G 4-way Tip (Without CC)| 22049452| 1608003817
51| 4596| Tip Retainer| 22034500| 1608003673
52| 5700-B| C&C Extension| 22049200| 1608003812
53
| | Complete 9″ Valve with Tip| 22042300| 1608003719
| Complete 9″ Valve with C&C Tip| 22042350| 1608003721
54
| | Complete 18″ Valve with Tip| 22042400| 1608003722
| Complete 18″ Valve with C&C Tip| 22042450| 1608003725
55
| | Complete 24″ Valve with Tip| 22042700| 1608003730
| Complete 24″ Valve with C&C Tip| 22042750| 1608003732
TROUBLESHOOTING
Problem
|
Solution
---|---
Valve body leaking| • Tighten packing nut, and replace packing washers.
Tip Leaking| • Clean or replace the soft seat gasket, and replace the
valve spring.
• Replace the tip washer.
CONTACT
Contact your local distributor or Pelsis country-specific location for
information on spares and service.
- US: B&G Equipment, 135 Region South, Jackson, GA, 30233, USA
- Contact Number: 1-800-544-8811
- Email Address: CustomerService@BGEquip.com
- UK: Pelsis Ltd, Sterling House, Grimbald Crag Close, Knaresborough, HG5 8PJ, UK. Contact Number: +44 (0) 800 988 5359
- Europe: Pelsis Belgium NV, Industrieweg 15, 2880, Bornem, Belgium.
- Contact Number: +32 (0) 3 886 22 11
- All Other Countries: B&G Equipment, 135 Region South, Jackson, GA, 30233, USA Contact Number: 1-678-688-5601
- Email Address: CustomerService@BGEquip.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>