OLIGHT Perun 2 Head Torch Orange User Manual

: June 3, 2024
: OLIGHT

Table of Contents

OLIGHT Perun 2 Head Torch Orange
IN THE BOX
Specification
- SUPPORTED BATTERY
BEFORE FIRST USE
CHARGING
HOW TO OPERATE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OLIGHT Perun 2 Head Torch Orange

OLIGHT-Perun-2-Head-Torch Orange-product-image

IN THE BOX

All performance measurements in accordance with ANSI/NEMA FL1-2009 standards. The tests are performed using the battery included in the flashlight, and are measured indoors under a room temperature of 25 degrees Celsius with windless conditions.
*The runtime of turbo and high modes may vary depending on the external temperature and ventilation conditions, these biases may affect the results of testing

Specification

SUPPORTED BATTERY

The light is equipped with a customized 21700 rechargeable battery. In case of emergency, other brand’s 21700 battery with built-in protection board can be used (but charging is not supported). It may turn off due to other brand’s low battery protection current

OLIGHT-Perun-2-Head-Torch Orange-3

BEFORE FIRST USE

Remove the protective film from the lens, unscrew the body and remove the yellow insulating film.

CHARGING

Connect the magnetic USB end of the charging cable to an external USB power source, then attach the other end of the magnetic charging cable to the charging port. It takes no more than 3.5 hours to fully charge the light ( For reference only. When the USB power supply is insufficient to provide 5V 2A power capacity, the charging time will be longer ).
Before the first use please fully charge the product.
Only charge with standard USB magnetic charging cable, not compatiable with other USB magnetic charging cable.

LANYARD ATTACHMENT

Put the pin tool through the light lanyard hole and then hook the lanyard to the hole.

PROXIMITY PROTECTION FUNCTION

When the proximity sensor detects an obstruction nearby, the brightness will automatically reduce. The light will shut down directly if the blockage continues for more than 60 seconds. The sensor is sensitive to occlusion only (the sensing distance will be different due to different colors and materials).

ATTENTION

Please keep the surface of the lens clean. Stains or water mist will affect the performance of the built-in sensor
located in the black area, resulting in the failure of high and above modes, please erase in time.
Pay attention to protect the lens from scratches. Scratches on the surface of the lens will reduce the luminous flux. In severe cases, it will affect the internal sensor performance, resulting in the failure of high and above modes.

HOW TO TURN IT INTO A HEADLAMP

Remove the pocket clip.
Put the flashlight into the bracket with the tail first.
Adjust the flashlight to the appropriate position.

DANGER

DO NOT throw the light directly into human eyes. This may cause temporary blindness, or permanent damage to the eyes.
The battery can only be charged while installed in the flashlight. When charging, please use the provided charger for your light.

WARNING

Keep out of reach of children.
If the light is about to be put aside for a long time or be transported, please unscrew the body for half a circle to cut off the circuit.
DO NOT use the turbo mode continuously when the environmental temperature is high in case the light body is too hot to hold.
Ensure the battery is inserted with the negative ( – ) end pointing to the head of the light ( LED side ).
Take good care of the battery; if the battery needs to be replaced, please keep the removed battery in a safe place. DO NOT mix it with the conductive metals.

NOTICE

Moonlight and turbo mode are not the normal brightness levels ( low, medium, and high mode ). Under moonlight and turbo mode, press and hold the switch to enter the normal brightness level cycle.
When the light is turned on, the light will return to the last used setting. Only moonlight, low, medium, and high mode can be memorized when the light is turned off. If the light is turned off on turbo mode, it will memorize high mode and will revert to the medium setting after 10 minutes. SOS mode cannot be memorized.
When the battery capacity is less than 60%, the internal MCU will automatically shield the turbo mode and reset high mode to the highest brightness level.
Active thermal management: On turbo mode, overheating can be avoided by adjusting the power output.

HOW TO OPERATE

ON/OFF: When the light is not locked out, single click switch to turn on/off.

CHANGE BRIGHTNESS LEVEL: When the light is on, press and hold the switch to cycle through the mode sequence moonlight (or turbo, SOS) – low – medium – high – low. The mode is selected when the switch is released.

MOONLIGHT MODE: When the light is off or in standby mode, press and hold the switch for over one second to access the moonlight mode.

DIRECT ACCESS TO TURBO: Enter and exit Turbo mode: quickly double click the switch to enter Turbo mode, and quickly double-click the switch again to exit Turbo mode.When the memorized mode is on high, quickly double-click the switch to exit Turbo mode and switch to medium mode. When the memorized mode is Medium, Low, or Moonlight, quickly double click the switch to exit turbo mode and switch to the previously memorized mode.

SOS: Quickly triple click the switch to access the SOS mode.

TIMER: The Perun 2 has a long (9 minutes) and short (3 minutes) timer when the light needs to be automatically turned off. When the flashlight is on, double click and hold the switch under the current brightness level to access the timer settings. A single blink accesses the short timer while two blinks accesses the long timer. The flashlight will automatically turn off when the timer is up. After the timer is set, double click and hold the switch to shift the timer settings. When the timer is up and the user is about to enter the timer again, the light will return to the last timer setting.

LOCKOUT: When the light is off, press and hold the switch for two seconds to access the button lockout mode. Under the lockout mode, press and hold the switch for less than two seconds without releasing it and the light will enter the moonlight mode again. The light will quit the moonlight mode once the switch is released and it will return to and stay at the button lockout mode.

BUTTON UNLOCK: Press and hold the switch for about two seconds until the light gives a single blink and then release the switch. The light will unlock and will return to the moonlight mode.