Arktic 233283 Refrigerated Display Cabinets User Manual

REFRIGERATED
DISPLAY CABINETS
**233276, 233283

**

233283 Refrigerated Display Cabinets

Read user manual and keep this with the appliance.

For indoor use only.

NOTE: This manual is translated from original English manual using AI and machine translations.

Technical specifications

A: Item no.
B: Rated voltage and frequency
C: Rated input power
D: Power of the light (LED)
E: Rated Current
F: Refrigerant used and injection quantity
G: Temperature setting
H: Protection class (Class)
I: Climate class
J: Noise level (approx. dB(A))
K: Foam blowing agent (Cyclopentane)
L: Inside cabinet capacity
M: Maximum shelf load
N: Dimensions
O: Net weight
Remark: Technical specification is subjected to change without prior notification.

Dear Customer,
Thank you for purchasing this Arktic appliance. Read this user manual carefully, paying particular attention to the safety regulations outlined below, before installing and using this appliance for the first time.

Safety instructions

• Only use the appliance for the intended purpose it was designed for, as described in this manual.
• The manufacturer is not liable for any damage caused by incorrect operation and improper use.
• DANGER! RISK OF ELECTRIC SHOCK! Do not attempt to repair the appliance by yourself. Do not immerse the electrical parts of the appliance in water or other liquids. Never hold the appliance under running water.
• NEVER USE A DAMAGED APPLIANCE! Check the electrical connections and cord regularly for any damage. When damaged, disconnect the appliance from the power supply. Any repairs should only be carried out by a supplier or qualified person to avoid danger or injury.
• WARNING! When positioning the appliance, route the power cable safely if necessary to avoid unintentional pulling, being damaged, coming into contact with the heating surface, or causing a tripping hazard.
• WARNING! As long as the plug is in the socket the appliance is connected to the power supply.
• WARNING! ALWAYS switch off the appliance before disconnecting from the power supply, cleaning, maintenance or storage.
• Only connect the appliance to an electrical outlet with the voltage and frequency mentioned on the appliance label.
• Do not touch the plug/electrical connections with wet or damp hands.
• Keep the appliance and electrical plug/connections away from water and other liquids. If the appliance falls into water, remove the power supply connections immediately.
• Do not use the appliance until it has been checked by a certified technician. Failure to follow these instructions will cause life threatening risks.
• Connect the power supply into an easily accessible electrical outlet so you can disconnect the appliance immediately in case of emergency.
• Make sure the cord does not come in contact with sharp or hot objects and keep it away from open fire. Never pull the power cord to unplug it from the socket, always pull the plug instead.
• Never carry the appliance by its cord.
• Never try to open the housing of the appliance yourself
• Do not insert objects into the housing of the appliance.
• Never leave the appliance unattended during use.
• This appliance should be operated by trained personnel in kitchen of the restaurant, canteens or bar staff, etc.
• This appliance should not be operated by persons with reduced physical, sensory or mental capabilities, or persons that have a lack of experience and knowledge.
• This appliance should, under any circumstances, not be used by children.
• Keep the appliance and its electrical connections out of reach of children.
• Never use accessories or any extra devices other than those supplied with the appliance or recommended by the manufacturer. Failure to do so could pose a safety risk to the user and could damage the appliance. Only use original parts and accessories.
• Do not operate this appliance by means of an external timer or remote-control system.
• Do not place the appliance on a heating object (gasoline, electric, charcoal cooker, etc.).
• Do not cover the appliance in operation.
• Do not place any objects on top of the appliance.
• Do not use the appliance near any open flames, explosive or flammable materials. Always operate the appliance on a horizontal, stable, clean, heat-resistant and dry surface.
• The appliance is not suitable for installation in an area where a water jet could be used.
• Leave a space of at least 20 cm around the appliance for ventilation during use
• WARNING! Keep all ventilation openings on the appliance free from obstruction.

Special safety instructions

• This appliance is intended for commercial and professional use only.
• Do not overload the interior shelves. The maximum load refers to “Technical specifications”
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• **CAUTION! RISK OF   FIRE!** The refrigerant used is R290. It is a flammable refrigerant which is environmentally friendly. Although it is flammable, it does not damage the ozone layer and does not increase the greenhouse effect. The use of this coolant has, however, led to a slight increase in the noise level of the appliance. In addition to the noise of the compressor, you might be able to hear the coolant flowing around the system. This is unavoidable, and does not have any adverse effect on the performance of the appliance. Care must be taken during the transportation and setting up of the appliance that no parts of the cooling system are damaged. Leaking coolant can damage the eyes.
• The foam blowing agent used is Cyclopentane in this appliance. It is highly flammable.
• CAUTION! RISKOFBURNS! Refrigerant liquid sprayed on the skin can cause critical burns. Keep eyes and skin protected. If refrigerant burns occur, rinse immediately with cold water. In case burns are severe, apply ice and contact medical treat- ment immediately.
• WARNING! Provide sufficient ventilation in the surrounding structure when building-in. Never block the air flow suction and air outlet in order to keep air circulation
• WARNING! Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
• WARNING! Do not damage the refrigerant circuit.
• WARNING! Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
• Do not place any dangerous products, such as fuel, alcohol, paint, aerosol cans with a flammable propellant, flammable or explosive substances, etc. inside or near the appliance.
• Once installed, the appliance must not be tilted at an angle greater than 5° and it is necessary to wait 2h before connecting it to the power supply to switch it on. The same applies if the appliance is moved afterwards.
• If the appliance has been switched off or disconnected from the power supply, it is necessary to wait 5 minutes until switching on again.
• No other appliances should be plugged into the same socket as with this appliance.
• Do not attempt to climb onto the appliance.
• Do not overload the interior shelves. The maximum load refers to “Technical specifications”

Intended use

• This appliance is intended to be used for commercial applications, for example in kitchens of restaurants, canteens, hospital and in commercial enterprises such as bakeries, butcheries, etc., but not for continuous mass production of food.
• The appliance is designed to keep food or beverages, under cool state and to display them for retail sale in restaurants, canteens, other commercial enterprises such as bakeries, butcheries, supermarkets, etc. Any other use may lead to damage to the appliance or personal injury.
• Operating the appliance for any other purpose shall be deemed a misuse of the device. The user shall be solely liable for improper use of the device.

Grounding installation

This appliance is classified as protection class I and must be connected to a protective ground. Grounding reduces the risk of electric shock by providing an escape wire for the electric current.
This appliance is fitted with a power cord with grounding plug or electrical connections with grounding wire. The connections must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)

1. Air outlet
   • Never block the air outlet. Let inside circulating cold air flow out.

2. Rack
   • The height of rack is adjustable for various goods.
   For adjustment:

1. Take out the rack
2. Move the rack support on suitable height.
3. Put the rack on the support.

3. Digital controller

4. Castor

5. Air suction
   • Never block the suction. Air is sucked in and cold air in circulated inside the refrigerator.

6. Glass door

7. Power Switch
   Remark: The content of this manual applies for all listed items unless specified otherwise. The appearance may vary from the shown illustrations.
   Control panel
   (Fig.2 on page 3)

8. Up

9. Illumination

10. Refrigerant LED

11. Defrost LED

12. Set

13. Down Circuit diagram

(Fig.3 on page 4)
A: Overheating protective probe
B: Defrost probe
C: Thermostat probe
D: Digital temperature controller
E: Display panel
F: Power switch
G: Fan Motor
H: Fan Motor
I: Lamp
J: Fan Motor
K: Overload protector
L: Compressor
M: PTC

Preparation before use

• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all accessories. In case of incomplete or damaged delivery, please contact the supplier immediately. In this case, do not use the device.
• Clean the accessories and the appliance before use (See ==> Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in the future.
• Keep the user manual for future reference.

NOTE! Due to manufacturing residues, the appliance may emit a light odor during the first few uses. This is normal and does not indicate any defect or hazard. Make sure the appliance is well ventilated.

Operating instructions

• Connect the power plug with a suitable electrical outlet. Leaving the appliance for running some hours to reach the cooling temperature before placing the beverage or food inside the appliance.
1). Setting the temperature

• Press SET to enter into the setting mode. The set temperature is displayed.
• Press Up or Down to increase or decrease the set temperature.
• Press SET again to confirm the setting and exit. Then, inside cabinet temperature is displayed.

NOTE:

• If no button is pressed within 10 seconds. The newly set temperature will be stored.
• The temperature setting  range from 2°C to 6°C. The actual temperature inside the appliance can be affected by the ambient  temperature.
• Keep the door open time as short as possible in order to keep a cool temperature inside.

2). Illumination inside the cabinet

• Press Illumination to switch ON the light. Press Illumination again to switch OFF the light.

3). Refrigerant LED indicator

• During the cooling operation (compressor enabled), this refrigerant LED indicator will lights up constantly.
• After the inside cabinet reach the set temperature, the refrigerant LED indicator will flashes continuously.
• When defrost start, the refrigerant LED indicator light off.

4). Defrost LED indicator

• During the defrost operation, this defrost LED indicator will lights up constantly.
• After the defrost operation, defrost LED indicator will lights off.

Cleaning & maintenance

• ATTENTION! Always disconnect the appliance from the power supply and cool down before storage, cleaning & maintenance.
• Do not use water jet or steam cleaner for cleaning and do not push the appliance under the water as the parts will get wet and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this can adversely affect the life of the appliance and result in a dangerous situation.

Cleaning

• Clean the cooled exterior surface with a cloth or sponge slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned before and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or cleaning agents containing chlorine. Do not use steel wool, metallic utensils, or any sharp or pointed objects for cleaning. Do not use petrol or solvents!
• No parts are dishwasher safe.

about 10 to 20 minutes.
•Rinse under running water thoroughly.| Dry all parts well at last.
External glass surfaces| •Wipe clean with a soft cloth and a little neutral detergent. Make sure no water or moisture enters inside the of the appliance.
Interior glass surfaces| •Remove any food deposits.
•Wipe clean with a soft cloth and a little mild detergent. Make sure no water or moisture enters inside the of the appliance.
Glass door

Maintenance

• Check the operation of the appliance regularly to prevent serious accidents.
• If you see that the appliance is not working properly or that there is a problem, stop using it, switch it off and contact the supplier.
• All maintenance, installation and repair work must be carried out by specialised and authorised technicians, or recommended by the manufacturer.

Transportation and Storage

• Before storage, always make sure that the appliance has been disconnected from the power supply and completely cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could damage it.
• Do not move the appliance while it is under operation. Disconnect the appliance from power supply when moving and hold it at the bottom.
• Special care must be taken when moving or transporting the machine due to its heavy weight. With at least 2 persons or using a cart. Move the machine slowly, carefully, and never incline more than 45°.

Troubleshooting

If the appliance does not function properly, please check the below table for the solution. If you are still unable to solve the problem, please contact the supplier/service provider.

The appliance does
not start cooling
after connect to
electrical power
supply.| Thermal cut-outactivated| Contact the  supplier.
The compressor is defective.
The power plug is connected correctly with the
power supply outlet.| Check the connection and make sure all the connections are correctly connected.
Cooling is not
enough.| The appliance is under strong sunlight radiationor close to a heat source.| Move the appliance a new location to avoid direct sunlight.
The doors are not properly closed or the sealing gasket is defective.| Close the doors properly.
Too much food is placed inside the appliance.| Place less food inside the appliance.
Surrounding ventilation is insufficient.| Check that if sufficient ventilation is povided by allowing at least 20cm away from other objects or  wall.
Too much noise| The appliance is not placed horizontally.| Check to make sure the appliance is placed horizontally.
The appliance touches surrounding wall or
other objects.| Check to make sure that at least 20cm away from other objects or wall.
There are some loose parts inside the appliance.| Contact the supplier.

Warranty

Any defect affecting the functionality of the appliance which becomes apparent within one year after purchase will be repaired by free repair or replacement provided the appliance has been used and maintained in accordance with the instructions and has not been abused or misused in anyway.
Your statutory rights are not affected. If the appliance is claimed under warranty, state where and when it was purchased and include proof of purchase (e.g. receipt).
In line with our policy of continuous product development we reserve the right to change the product, packaging and documentation specifications without notice.

Discarding & Environment

**** When decommissioning the appliance, the product must not be disposed of with other household waste. Instead, it is your responsibility to dispose to your waste equipment by handing it over to a designated collection point. Failure to follow this rule may be penalized in accordance with applicable regulations on waste disposal. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local waste collection company. The manufacturers and importers do not take responsibility for recycling, treatment and ecological disposal, either directly or through a public system.

HENDI B.V.
Innovatielaan 6
6745 XW De Klomp, The Netherlands
Tel: +31 317 681 040
Email: info@hendi.eu
HENDI Polska Sp. z o.o.
ul. Firmowa 12
62-023 Robakowo, Poland
Tel: +48 61 658 7000
Email: info@hendi.pl| PKS HENDI South East Europe SA
5 Metsovou Str.
18346 Moschato, Athens, Greece
Tel: +30 210 4839700
Email: info@pks-hendi.com
HENDI Italia S.R.L.
Via Leonardo da Vinci 4
39100 Bolzano (BZ), Italy
Tel: +39 800 727 438
Email: office.italy@hendi.eu
---|---
HENDI GmbH
Ehring 15
5112 Lamprechtshausen, Austria
Tel: +43 6274 200 10 0
Email: office.austria@hendi.eu
HENDI Romania S.R.L.
Str. 13 decembrie 94A, Hala 14
Brașov, 500164, Romania
Tel: +40 268 320330
Email: office@hendi.ro| HENDI HK Ltd.
1208, 12/F Exchange Tower
33 Wang Chiu Road, Kowloon Bay, Hong Kong
Tel: +852 2154 2618
Email: info-hk@hendi.eu
Find HENDI on internet:
www.hendi.com
www.facebook.com/HendiToolsforChefs
https://www.linkedin.com/company/hendi-tools-for-chefs/
www.youtube.com/HendiEquipment

Changes, printing and typesetting errors reserved.
© 2023 HENDI B.V. De Klomp – The Netherlands
Ver: 09-03-202

References

• hendi.com
• hendi.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>