HAZET 1847-12/15 Circlip Pliers Set User Manual

HAZET 1847-12/15 Circlip Pliers Set User Manual

For your Information

General information

• Please make sure that the user of this device carefully reads these operating instructions and fully understands all information given before it is used.
• These operating instructions contain important advice that is necessary for the safe and troublefree operation of your HAZET circlip pliers set.
• Using the HAZET circlip pliers set as intended requires complete compliance with all of the safety instructions and information in these operating instructions.
• For this reason, always keep these operating instructions together with your HAZET circlip pliers set.
• This tool has been designed exclusively for specific applications. HAZET emphasizes that any modification to the tool and/or use in a way that does not correspond to its intended application is strictly forbidden.
• HAZET will not be liable for any injuries to persons or damage to property originating from improper application, misuse of the tool or a disregard of the safety instructions.
• Furthermore, the general safety regulations and regulations for the prevention of accidents valid for the application area of this device must be observed and respected.

Explanation of symbols

Attention: Pay strict attention to these symbols!

**READ THE OPERATING INSTRUCTIONS!

**The operator is obligated to comply with the operating instructions and to instruct all users of the HAZET circlip pliers set in accordance with the operating instructions.

NOTE!

This symbol indicates advice that is helpful when using the tool.

WARNING!

This symbol indicates important specifications, dangerous conditions, safety risks and safety advice.

CAUTION!

This symbol indicates advice which, if disregarded, results in damage, malfunction and/or functional failure of the tool.

TO BE USED BY QUALIFIED PERSONNEL ONLY!

This tool may cause serious injury and must therefore be used by qualified personnel only.

Always ensure that the drive shaft joint is aligned to the drive shaft.

For your safety

Owner’s liabillty

• The tool was developed and manufactured according to the technical norms and standards valid at the time and is considered to be operationally reliable. Nevertheless, the tool may present a danger when it is not used as intended or used in an inappropriate way by non-qualified personnel.
  Please make sure that any person using this device or carrying out any maintenance work carefully reads these operating instructions and fully understands all the provided information before using the device.

• Keep the operating instructions together with the device at all times.

• Any modification of the tool is strictly forbidden.

• All security advices, warning and operation notices on the tool have to be kept legible. Immediately replace any damaged labels or stickers.

• All specified set values or ranges must be observed.

• These instructions are provided as a guide only.
  Always make sure that you have a copy of the appropriate vehicle manufacturer’s service instructions, or another appropriate manual that provides the correct information needed to correctly execute the work.

Intended use

Operational reliability is only guaranteed if the tool is used as intended in accordance with the information in the operating instructions.
In addition to the safety advice given in these operating instructions, the general safety regulations, regulations for the prevention of accidents and regulations for environmental protection valid for this tool’s application range must be observed and respected.
Always ensure tools are used, inspected and maintained in compliance with the respective local, state, national or federal regulations.

• The tool must only be used if it is in good working condition.
• For installing the drive shaft joint for drive shafts with internal, covered circlips.
• Any deviation from the intended use and/or any misapplication of the device is not allowed and will be considered as improper use.
• Any claims against the manufacturer and/or its authorised agents because of damage caused by improper use of the tool are void.
• Any personal injury or material losses caused by improper use of the tool are the sole responsibility of the owner.

Dangers that may arise from using the tool

**** Before each use, check that the HAZET circlip pliers set is correct and fully functional. Do not use the HAZET circlip pliers set if correct functionality cannot be ensured or if damage is detected. If the HAZET circlip pliers set is used when not in full working order,you risk severe personal injury as well as damage to health and property.

• The device is fully functional when:
  • The tool runs smoothly.
  • The device does not show any signs of damage.
• The component parts must only be used in combination and as intended.
• When working with the HAZET circlip pliers set, ensure that protective goggles and tight-fitting protective work clothing are worn.
• Always have service or repair work performed by qualified personnel. Only use original spare parts so as to guarantee its long-term operational safety.
• For safety reasons, any modifications of the HAZET circlip pliers set are strictly prohibited. Any modification of the HAZET circlip pliers set will result in immediate invalidation of the warranty and exclusion from liability.

The circlip must not tilt.

Design and function

Technical data / tool components

Components

_ _HPZET
__ No.| Designation|
---|---|---
1 1847-12| Circlip pliers| 1
2 1847-121/2| Half shell pair (019.0mm)| 1
3 1847-122/2| Half shell pair (021.4mm)| 1
4 1847-123/2| Half shell pair (022.3-23.0mm)| 1
5 1847-124/2| Half shell pair (023.8-24.6mm)| 1
6 1847-125/2| Half shell pair (026.2-26.9mm)| 1
7 1847-126/2| Half shell pair (028.5-29.2mm)| 1
8 1847-127/2| Half shell pair (030.0mm)| 1
9 1847-128/2| Half shell pair (032.8mm)| optional

Use

• These instructions are provided as a guide only. Always make sure that you have a copy of the appropriate vehicle manufacturer’s service instructions or another appropriate manual that provides the correct information needed to correctly execute the work.
• The circlip must not tilt.
• Always ensure that the drive shaft joint is aligned to the drive shaft.
• Damage to the serration of the drive shaft joint and the drive shaft is avoided.
• If necessary, loosen or remove any attached parts.
• Less effort required when opening the drive shaft joint since the protruding circlip is tensioned in the groove.
• Easier attachment and sliding of the drive shaft joint onto the drive shaft by a special half shell shaping.

Always ensure that the drive shaft joint is aligned to the drive shaft.

Installation

• Place the circlip in the drive shaft groove. Fig. 1.
  

• Measure the outer diameter of the serration. Choose the suitable half shell size which sufficiently encloses the serration.
  Note: Size information can be found on the underside of the half shells. Fig. 2
  

• Insert the corresponding half shells in the circlip pliers 1847-12 above the cylindrical guide until they engage. Fig. 3
  

• Place the circlip pliers over the circlip on the drive shaft serration and secure the circlip pliers. Position the drive shaft joint on the half shells. Always ensure that the drive shaft joint is aligned to the drive shaft.
  The serration should be easy to fit. Fig. 4
  Note: Ensure that the half shells do not protrude over the drive shaft, as this hinders the insertion of the serration.
  

• Strike the drive shaft joint with a soft-faced hammer. This pushes the circlip pliers down onto the serration. Fig. 5
  Once the drive shaft joint is in the correct position, you can loosen the circlip pliers and remove them from the drive shaft.
  
  Note: Check that the drive shaft joint is placed correctly. The circlip prevents the drive shaft joint from being pulled off the drive shaft. Note: Vehicle manufacturer information must be strictly observed and followed!
  Then install the further components according to the corresponding application notes and manufacturer information.

Maintenance and care

Maintenance and care

• Always keep the tool clean.

• Do not use degreasing agents or water in order to avoid corrosion.

• Inspection and repair may only be carried out by qualified personnel.
  Your contacts for:

  • Warranty
  • Maintenance and repair
    service-center@hazet.de

Spare parts

• Only use the manufacturer’s original spare parts.
• For questions and spare parts orders, please indicate the article number of the device.
• Unsuitable or defective spare parts may cause damage, malfunction or total failure of the device.
• The use of non-approved spare parts will void all warranty, service and liability claims as well as all claims for compensation against the manufacturer or its agents, distributors and sales representatives.

Storage

The tool must be stored according to the following conditions:

• Do not store the tool outdoors.
• Keep the tool in a dry and dust-free place.
• Do not expose the tool to liquids and/or aggressive substances.
• Storage temperature: -10 to +45 °C.
• Relative air humidity: max. 60%.

Disposal

For disposal, clean the device and disassemble it according to the regulations for work safety and environmental protection. Please recycle components.

Support

HAZET-WERK  Hermann Zerver GmbH & Co. KG
10 04 61 · 42804 REMSCHEID · GERMANY
Güldenwerther Bahnhofstraße 25 – 29 · 42857 REMSCHEID · GERMANY
+49 (0) 21 91/ 7 92-0
FAX: +49 (0) 21 91 / 7 92-375 (National) -400 (International)
www.hazet.de
E-mail: info@hazet.de

References

• HAZET-WERK - Hermann Zerver GmbH & Co. KG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>