Haloview M7108 2.4G Digital 720P 7Inch LCD Wireless Monitor User Manual

: June 3, 2024
: Haloview

Haloview M7108 2.4G Digital 720P 7Inch LCD Wireless Monitor

Haloview-M7108-2-4G-Digital-720P-7Inch-LCD-Wireless-Monitor-
PRODUCT

Precautions

Storage

Do not expose the monitor to extreme heat, cold, or sudden temperature changes. ° The storage temperature of this device is -30 to+ 80 C or -22 to +176° F . The ° operating temperature is -20 to+ 70 C or -4 to 158°F with the humidity under RH90%.
Never use this device in environments with excessive moisture, dust or smoke.
Avoid dropping or striking this device.
Never puncture, scratch or use abrasive cleaning materials on this device.
Leave at least a 2″ space between the monitor and walls, cabinets or other objects to allow adequate air circulation around the device.
The monitor is not designed to be waterproof.

Operating Precautions

The device can be powered by a 10 -32 volt automotive battery or vehicle electrical system.
Improper cable connections may damage the monitor. Remove the power cable connections when you do not intend to use the device.

warning

High voltage is present within the monitor. The opening of the case should be by professionals.
Do not watch the video while driving unless you are monitoring the rear view camera display.

Special Notice

Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very common phenomenon in active matrix display technology, and doesn’t necessarily indicate any defects or faults. Never try to repair this device by yourself. In case of any problems, please turn off the display at once and notify our company or authorized dealer. The monitor is a complex device. Any disassembly or modification may lead to damage and void the warrantee.

Maintenance

Remove all the cable connections from the monitor before cleaning the device.
Use a mild household detergent and clean the unit with a slightly damp, soft cloth. Never use strong solvents such as thinner or benzine, as they might damage the finish of the device.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

WARNING

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Declaration of conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

Accessories

Haloview M5111 2.4G Digital 720P 5Inch-LCD-Wireless-Monitor-
FIG1

Please pair the camera with the monitor by using external 12V power supply and provided Pairing Cable before installing this system on your RV .

Special Notice

Accessories supplied in kit may be different for each application.

Features

NORMAL, MIRROR, FLIP and MIR-FLIP viewing are available.
Split mode, auto-scan mode and single-display mode available.
Auto pairing: Auto pairing happens when camera is activated.
Auto dim function is available.
Support up to 4 wireless cameras.
Multiple video formats: PAL/ NTSC.
Wide voltage input: 10 – 32V.
Built-in DVR

Specifications

Haloview M5111 2.4G Digital 720P 5Inch-LCD-Wireless-
Monitor-FIG2

Functions of each part

Haloview M5111 2.4G Digital 720P 5Inch-LCD-
Wireless-Monitor-FIG3

Basic Operation

Installation of Center Mounting Bracket:
- Adjust monitor height by sliding the monitor up or down in the slot, then the tight knob.
- Adjust the monitor angle by loosening the lower knob on the center mounting bracket, tilting the monitor to the desired angle, and re-tighten the knob.
Installation of U-support Bracket
Please mount the camera on the license plate back if you plan to install the camera on your plate

Special Notice
It is not recommended to mount the camera on a license plate if your vehicle is longer than 20 ft.

Wiring Instruction

Camera Wiring
Power on the camera by connecting the Red positive wire to the 10 – 32 VDC power source, the Black to the Negative/Ground source, and connecting camera plug.

Monitor Wiring
This is the most commonly used method for users who have a single-camera system. (one monitor and one camera). Connect the monitor with BMW connector adaptor, connect the DC connector of BMW connector adaptor to cigarette lighter. Power the monitor by vehicle 12V through the cigarette lighter.

For more cameras, extra cameras can be paired separately to CAM 1 /CAM2/CAM3/CAM4. Please refer to page1 g PAIRING. CAM4 will be the only channel which will display parking lines. If you need parking lines, please pair a camera to CAM4. You can easily switch camera display by pressing SEL button.

Installation

Please find the best signal reception position before the installation
The metal body of the vehicle can attenuate wireless signal strength sharply. It is necessary to test the signal strength before installation.

Please connect the monitor and camera as below picture
Pairing the camera to the monitor, please refer to page 19 PAIRING. 4 cameras can be paired separately to CAM1/CAM2/CAM3/CAM4.
Put the monitor and the camera at the intended position to test signal strength.

If the signal strength of the position that you planned to install a camera is under 2 bars, please change to another position, or mount the camera higher to make sure the antenna highest of the top without being blocked. Please refer to the below pictures:

Installation Position 1: Mount the camera higher than your vehicle’s roof, keeping the antenna vertical.
Installation Position 2: Mount the camera lower but as close as possible to the vehicle’s roof, and move the antenna outward 15-30 degrees. The antenna’s proximity to any metal surfaces on the vehicle may affect signal strength.
Special Notice
After position adjustment, you can start the installation if your signal strength is still above 2 bars.

Antennas should be vertically lined to the ground. Make sure there is no obstacle around antennas.
Magnet-based extension antenna should be attached on the top of the vehicle. Make sure there is no obstacle around.

If you get poor signal reception or the signal cannot reach at least 2 bars, please adjust the angle of the antenna to find best signal reception position.

Antenna

Button Function

Press the menu button to enter below interface. Haloview M5111 2.4G Digital
720P 5Inch-LCD-Wireless-Monitor-FIG15
Volume
MENU is only allowed for operation under single image mode, not quad mode. Press MENU to display the following options and settings:

1. Press to select VOLUME, and Press OK to confirm. Press to adjust settings.

Press and OK button to set MUTE or UNMUTE.

Picture

Press the MENU button to enter the menu interface.
Press to select PICTURE, and Press OK to enter.
Press to select BRIGHTNESS/CONTRAST/COLOR,

Mirror

Press the MENU button to switch to enter menu interface. Press to select MIRROR. Press OK button to enter MIRROR setting.
Press to select NORMAL/MIRROR/MIR-FLIP/FLIP.

Q-mode

Press the MENU button to enter the menu interface. Press and OK button
Press to select the display mode.
After setting, press the SEL button to change display mode. For example, If you set QUAD mode”

Pressing the SEL button 4 times, the display will switch CAM 1 to QUAD. Haloview M5111 2.4G Digital 720P 5Inch-LCD-Wireless-Monitor-
FIG25

Autoscan

Press the MENU button to enter the menu interface. Press and OK button to enterAUTOSCAN setting.
Press and OK button to set AUTO SCAN channels and SCAN TIME.
Press the SEL button to switch to the SCAN interface. A SCAN icon will appear on the display. Press again to exit SCAN mode.
Quad or Split Audio Setting When the monitor display Quad or Split picture, you can press the button to play audio of any of the CAM channel.

Setting

Press the MENU button to enter the menu interface. Press to select SETTING. Press OK button to enter SETTING.
SELKIE: User-defined CAM switching. For example, if CAM 1, CAM2, and Q(QUAD MODE) are selected, When pressing the SEL key, the display will switch from CAM1 to CAM2, and QUAD MODE, it will skip CAM3, CAM4, and SCAN.
Press OK to move selection, and press the key to select or cancel. The bottom yellow dot indicates the current selection.

Park-line

Press the MENU button to enter the menu interface. Press and OK button to enter PARK-LINE.
Display: To set the park line display in a certain channel of CAM. Press the button to select, and press the OK button to confirm.
Turn on/off parking lines or enter adjust parking lines setting.
Press or button to adjust the position of the parking lines.
Press or button to adjust the position of parking lines
Note: Parking lines only display on CAM4. If you need parking lines,

Record

Insert TF Card Please insert TF card in TF card slot, max 128G Micro-SD/TF Card
Format the TF card.
Note: TF card must be formatted before use.
Press the MENU button to enter the menu interface, and enter the RECORD setting
When COVER is turned on, overwrite function will be activated. Previously recorded video files will be overwritten when TF card memory is full.
After the TF card is formatted, a yellow folder icon will be shown on the screen, indicating the TF card is available now.
After setting, turn on RECORD to start recording or pause recording, or, you can press the OK button to start recording or pause recording.

Note: Pressing the OK button in the QUAD or SPLIT display, the monitor will record all displayed channels of CAM at the same time.

Play Recorded File Recorded videos can be played by a monitor.

Press and OK button to enter PLAY.
Press and OK button to select a file.
Press or select TIME& CHANNEL, and Press OK to enter.
Press the OK button to PLAY or PAUSE the file.

Recording Time
For Micro SD cards with different capacities, please refer to the table below for recording time under 3 different image modes. This table is for reference only. Data may vary under different environments. Haloview M5111 2.4G Digital
720P 5Inch-LCD-Wireless-Monitor-FIG42

Pairing

Press the SEL button to select a channel that needs to be paired.
Monitor Pairing
Method 1: Enter the menu interface and select PAIRING, press OK to confirm, you will have 20 seconds for pairing.
Method 2: Press the OK button for 3 seconds to enter PAIRING status, you will have 20 seconds for pairing.
Camera Pairing
Method 1: Press the pairing button on the back of the camera.
Method 2: Power off the camera and power on ii again.

The video will be displayed after the pairing is complete.

Special Notice
If no picture is displayed after pairing, please retry the pairing steps and power-on again the camera. The pairing must be completed within 20 seconds, otherwise you need to re-power the camera for pairing.

Troubleshooting

The symptoms described below do not necessarily mean a failure within the display. Please check the following items before you initiate a request for repair. Haloview M5111 2.4G Digital 720P 5Inch-LCD-Wireless-Monitor-
FIG45

Precautions

Storage

Do not expose the monitor to extreme heat, cold, or sudden temperature changes. ° The storage temperature of this device is -30 to+ 80 C or -22 to +176° F . The ° operating temperature is -20 to+ 70 C or -4 to 158°F with the humidity under RH90%.
Never use this device in environments with excessive moisture, dust or smoke.
Avoid dropping or striking this device.
Never puncture, scratch or use abrasive cleaning materials on this device.
Leave at least a 2″ space between the monitor and walls, cabinets or other objects to allow adequate air circulation around the device.
The monitor is not designed to be waterproof.

Operating Precautions

The device can be powered by a 10 -32 volt automotive battery or vehicle electrical system.
Improper cable connections may damage the monitor. Remove the power cable connections when you do not intend to use the device.

warning

High voltage is present within the monitor. The opening of the case should be by professionals.
Do not watch the video while driving unless you are monitoring the rear view camera display.

Special Notice

Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very common phenomenon in active matrix display technology, and doesn’t necessarily indicate any defects or faults. Never try to repair this device by yourself. In case of any problems, please turn off the display at once and notify our company or authorized dealer. The monitor is a complex device. Any disassembly or modification may lead to damage and void the warrantee.

Maintenance

Remove all the cable connections from the monitor before cleaning the device.
Use a mild household detergent and clean the unit with a slightly damp, soft cloth. Never use strong solvents such as thinner or benzine, as they might damage the finish of the device.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

WARNING

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Declaration of conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

Accessories

Please pair the camera with the monitor by using external 12V power supply and provided Pairing Cable before installing this system on your RV .

Special Notice

Accessories supplied in kit may be different for each application.

Features

NORMAL, MIRROR, FLIP and MIR-FLIP viewing are available.
Split mode, auto-scan mode and single-display mode available.
Auto pairing: Auto pairing happens when camera is activated.
Auto dim function is available.
Support up to 4 wireless cameras.
Multiple video formats: PAL/ NTSC.
Wide voltage input: 10 – 32V.
Built-in DVR

Specifications

Functions of each part

Basic Operation

Installation of Center Mounting Bracket:
- Adjust monitor height by sliding the monitor up or down in the slot, then the tight knob.
- Adjust the monitor angle by loosening the lower knob on the center mounting bracket, tilting the monitor to the desired angle, and re-tighten the knob.
Installation of U-support Bracket

Wiring Instruction

Camera Wiring
Power on the camera by connecting the Red positive wire to the 10 – 32 VDC power source, the Black to the Negative/Ground source, and connecting camera plug.

Monitor Wiring
This is the most commonly used method for users who have a single-camera system. (one monitor and one camera). Connect the monitor with BMW connector adaptor, connect the DC connector of BMW connector adaptor to cigarette lighter. Power the monitor by vehicle 12V through the cigarette lighter.

For more cameras, extra cameras can be paired separately to CAM 1 /CAM2/CAM3/CAM4. Please refer to page1 g PAIRING. CAM4 will be the only channel which will display parking lines. If you need parking lines, please pair a camera to CAM4. You can easily switch camera display by pressing SEL button.

Installation

Please find the best signal reception position before the installation
The metal body of the vehicle can attenuate wireless signal strength sharply. It is necessary to test the signal strength before installation.

Please connect the monitor and camera as below picture
Pairing the camera to the monitor, please refer to page 19 PAIRING. 4 cameras can be paired separately to CAM1/CAM2/CAM3/CAM4.
Put the monitor and the camera at the intended position to test signal strength.

If the signal strength of the position that you planned to install a camera is under 2 bars, please change to another position, or mount the camera higher to make sure the antenna highest of the top without being blocked. Please refer to the below pictures

Installation Position 1: Mount the camera higher than your vehicle’s roof, keeping the antenna vertical.
Installation Position 2: Mount the camera lower but as close as possible to the vehicle’s roof, and move the antenna outward 15-30 degrees. The antenna’s proximity to any metal surfaces on the vehicle may affect signal strength.
Special Notice
After position adjustment, you can start the installation if your signal strength is still above 3 bars.

Antennas should be vertically lined to the ground. Make sure there is no obstacle around antennas.
Magnet-based extension antenna should be attached on the top of the vehicle. Make sure there is no obstacle around.

If you get poor signal reception or the signal cannot reach at least 2 bars, please adjust the angle of the antenna to find best signal reception position.

Installation Position 1: Mount the camera higher than your vehicle’s roof, keeping the antenna vertical.
Installation Position 2: Mount the camera lower but as close as possible to vehicle’s roof, and move the antenna outward 15-30 degree. The antennas proximity to any metal Surfaces on the vehicle may affect signal strength.

Special Notice
After position adjustment, you can start the installation if your signal strength is still above 3 bars.

Button Function

MENU

```
1. Press menu button to enter below interface.  
```
Volume
MENU is only allowed for operation under single image mode, not quad mode. Press MENU to display the following options and settings:
Press to select VOLUME, and Press OK to confirm. Press to adjust settings.
Press and OK button to set MUTE or UNMUTE.

Picture

Press the MENU button to enter the menu interface.
Press to select PICTURE, and Press OK to enter.
Press to select BRIGHTNESS/CONTRAST/COLOR,

Mirror

Press the MENU button to switch to enter menu interface. Press to select MIRROR. Press OK button to enter MIRROR setting.
Press to select NORMAL/MIRROR/MIR-FLIP/FLIP.

Q-mode

Press the MENU button to enter the menu interface. Press and OK button
Press to select the display mode.
After setting, press the SEL button to change display mode. For example, If you set QUAD mode”

Pressing SEL button 4 times, the display will switch CAM 1 to QUAD.

Autoscan

Press the MENU button to enter the menu interface. Press and OK button to enterAUTOSCAN setting.
Press and OK button to set AUTO SCAN channels and SCAN TIME.
Press the SEL button to switch to the SCAN interface. A SCAN icon will appear on the display. Press again to exit SCAN mode.
Quad or Split Audio Setting When the monitor display Quad or Split picture, you can press the button to play audio of any of the CAM channel.

Setting

Press the MENU button to enter the menu interface. Press to select SETTING. Press OK button to enter SETTING.
SELKIE: User-defined CAM switching. For example, if CAM 1, CAM2, and Q(QUAD MODE) are selected, When pressing the SEL key, the display will switch from CAM1 to CAM2, and QUAD MODE, it will skip CAM3, CAM4, and SCAN.
Press OK to move selection, and press the key to select or cancel. The bottom yellow dot indicates the current selection.

Park-line

Press the MENU button to enter the menu interface. Press and OK button to enter PARK-LINE.
Display: To set the park line display in a certain channel of CAM. Press the button to select, and press the OK button to confirm.
Turn on/off parking lines or enter adjust parking lines setting.
Press or button to adjust the position of the parking lines .
Press or button to adjust the position of parking lines
Note: Parking lines only display on CAM4. If you need parking lines,

Record

Insert TF Card Please insert TF card in TF card slot, max 128G Micro-SD/TF Card
Format the TF card.
Note: TF card must be formatted before using.
Press the MENU button to enter the menu interface, and enter the RECORD setting
When COVER is turned on, overwrite function will be activated. Previously recorded video files will be overwritten when TF card memory is full.
After TF card is formatted, a yellow folder icon will be shown on the screen, indicating TF card is available now.
After setting, turn on RECORD to start recording or pause recording, or, you can press OK button to start recording or pause recording.

Note: Pressing the OK button in the QUAD or SPLIT display, the monitor will record all displayed channels of CAM at the same time.

Plav Recorded File

Play Recorded File Recorded videos can be played by a monitor.

Press and OK button to enter PLAY.
Press and OK button to select a file.
Press or select TIME& CHANNEL, and Press OK to enter.
Press OK button to PLAY or PAUSE the file.

Recording Time
For Micro SD cards with different capacities, please refer to the table below for recording time under 3 different image modes. This table is for reference only. Data may vary under different environments.

Pairing

Press SEL button to select a channel that needs to be paired.
Monitor Pairing
Method 1: Enter the menu interface and select PAIRING, press OK to confirm, you will have 20 seconds for pairing.
Method 2: Press the OK button for 3 seconds to enter PAIRING status, you will have 20 seconds for pairing.
Camera Pairing
Method 1: Press the pairing button on the back of the camera.
Method 2: Power off the camera and power on ii again.
Video wIll be displayed after the pairing is complete.

The video will be displayed after the pairing is complete.

Special Notice
If no picture is displayed after pairing, please retry the pairing steps and power-on again the camera. The pairing must be completed within 20 seconds, otherwise, you need to re-power the camera for pairing.