Haloview Sens 3 World-First Wireless Advanced Driving Assistance System User Manual

Haloview Sens 3 World-First Wireless Advanced Driving Assistance System User Manual

Precautions

Thank you for choosing our millimeter-wave blind spot monitoring system. This system is mainly composed of two millimeter-wave radar sensors, left and right alarm light buzzers, and a radar control box. It is a high-end blind spot monitoring and lane-changing auxiliary system. The product can simultaneously complete the distance and speed measurement of multiple targets behind the vehicle, and transmit it to the radar control box wirelessly. After that, the radar control box sends out an audible and visual alarm to remind the driver.

There is a certain blind spot in the vehicle rearview mirror angle of view, which brings safety hazards to driving, especially in bad weather, like snow or rain. Equipped with this millimeter wave blind spot monitoring system, once moving objects detected on both sides of the vehicle that approach the blind spot, a warning signal will be transmitted to the radar control box with alarm light flashing and beeping, which greatly reduce accident.

This product is easy to install and wiring-free. Magnetic bracket is supported for vehicles with metal surface (thicker than 1 mm). For other vehicles with plastic, glass fiber or aluminum alloy body surface, we provide adhesive metal plate, which can be used together with magnetic bracket.

Sincerely thank you for choosing our product, we wish you a pleasant journey!

IMPORTANT TIPS

Special vehicle conditions that should be considered
If the vehicle is driven before a GPS connection is established or if the GPS connection is interrupted (inside a tunnel, parking structure, etc), the system may not function properly, producing incorrect or false warnings or falling to produce a warning. Once the GPS connection is established or re- established, GPS indicator will flash.

The following may compromise the effectiveness of the system:

• Incorrect installation angle.
• Vehicle with metal obstruction in front of the sensor.
• Improper sensor mounting location on vehicle, ie. center of the vehicle bumper.

Situations that may affect system detection accuracy:

• Metal objects are in the direct path of the sensing signal.
• Weather such as heavy rain, snow, or icy road may cause changes in sensitivity.
• Gravel roads, which may cause interference due to dust and flying stones.

THIS PRODUCT FUNCTIONS ASAN AID FOR NOTIFYING THE PRESENCE OF OBSTACLES IN VEHICLE BLIND SPOTS. IT DOES NOT DETECT ALL DANGERS AND OBSTACLES, AND IS NOT A SUBSTITUTE FOR YOUR JUDGEMENTAND CAREFUL ATTENTION. BEFORE ANY MANEUVER, VISUALLY CHECK BOTH SIDES OF THE VEHICLE TO CONFIRM.

THE RADAR DETECTION SYSTEM DOES NOT REPLACE ANY FUNCTIONS DRIVERS SHALL ORDINARILY PERFORM IN DRIVING A MOTOR VEHICLE, NOR DOES IT DECREASE THE NEED FOR DRIVERS TO STAY VIGILANT AND ALERT IN ALL DRIVING CONDITIONS, TO OBEYALL THE SAFE DRIVING STANDARDS, PRACTICES, TRAFFIC RULES AND REGULATIONS.

HALOVIEW DOES NOT GUARANTEE 100% ACCURACY IN THE DETECTION OF VEHICLES OR PEDESTRIANS, AND THEREFORE DOES NOT GUARANTEE THE PERFORMANCE OF ANY RELATED AUDIO OR VISUAL WARNING SIGNALS. FURTHERMORE, ROAD, WEATHER AND OTHER CONDITIONS MAY ADVERSELY AFFECT THE VEHICLE’S RADAR DETECTION SYSTEM RECOGNITION AND RESPONSE CAPABILITIES.

CAREFULLY READ THIS INSTALLATION GUIDE AND ITS IMPORTANT SAFETY INSTRUCTIONSAND WARNINGS PRIOR TO INSTALLING OR USING THE HALOVIEW RADAR DETECTION SYSTEM.

WARNING

This product is only used as a driving assistance, do not rely too much on the rear-view radar. Drivers should abide by traffic laws and regulations to ensure their driving safety. It does not rule out the possibility of traffic accidents during the use of this product, and Haloview does not assume any responsibility.

IMPORTANT TIPS

Please take care of the radar sensors if you do not hard-wire them on your vehicle. Please remove them after each use in order to avoid missing. Haloview will not be responsible for the loss of the product.

• Radar Control Box X1

• Radar Sensor X2

• LED Indicator X2

• DC Extension Cable X2
  

• Antenna X2

• 3M tape X2

• Installation Angle Tool X1

• Cigarette Lighter X1

• Cushion Pad X2

OPTIONAL

• 3M  Tape

• Smart Battery Pack

• Power Adapter
  

Function

1. Detection range for vehicle is up to 70m. Detection range for pedestrian is up to 15m. It provides a reasonable warning signal according to speed difference.
2. The radar alarm signal is transmitted to the radar control box wirelessly, which can be installed without wiring (It is suggested to purchase our battery pack to realize portable application).
3. The alarm signal is reminded by sound and light, and the sound reminder function can be turned off.
4. Disarm alarm signal duration is settable according to different types of vehicles.
5. The speed per hour of starting the alarm signal can be set.
6. Lane change assist (LCA), overtaking early alarm (AOA), blind spot detection (BSD).
7. It can work all weathers, like fog, rain and snow. Please note that in severe weather such as heavy rain, the detection range may decrease.
8. The control box has a built-in lithium battery, which can be charged and discharged by cigarette lighter or power bank. It has overcharge and over-discharge protection.
9. Millimeter-wave radar sensors, waterproof grade IP67.

Alert Conditions

The system is designed to detect the following events:

1. Blind spots while driving: Objects in the blind spot areas around your vehicle–in the lanes on the left / right and directly behind the vehicle at a distance of up to 70m (depends on the speed difference).
2. Blind spots while being passed / overtaken: When vehicles are approaching / overtaking your vehicle from behind, or when your vehicle approaches and passes a moving vehicle.

Caution

The radar system can detect not only objects approaching your vehicle from behind, but also objects that your vehicle is approaching or overtaking. Under certain driving scenarios, the radar system may detect objects in an unintended way . The following conditions below are examples of scenarios where fault notifications may occur.

1. Vehicle behind is too close

2. Getting into wide lane when changing lanes

3. Vehicle detected while changing lane

4. Vehicle getting close when turning

5. Fence or concrete wall

6. Fence or wall is getting narrow

7. Tunnel entrance

8. Smaller turning radius

Specifications

Radar Sensor

Radar

Modulation| FMCW
Radar Distance| 0.5 – 70m
Range|
Distance(Vehicle)| <70m
Distance(Pedestrian)| <15m
Accuracy| 0.3m
Unit
Operating voltage| TX: 12V 360mA
Operating temperature| -20°C – 70°C
Storage temperature| -30°C – 80°C

Radar Control Box

Discharge: -10°C – 60°C
Storage temperature| -30°C – 70 °C

Functions of each part

The left alarm light on control box is synchronized with the left LED indicator

• Light off: no alarm signal
• Double flashing: left-side alarm signal
• Light on still: alarm signal has not been lifted

The right alarm light on control box is synchronized with the right LED indicator

• Light off: no alarm signal
• Double flashing: right-side alarm signal
• Light   on still: alarm signal has not been lifted

GPS signal light

• Green light off: The GPS module has no communication with the control box
• Green light on: The GPS module is communicating with the control box, searching for satellites
• Green   light flashes: GPS module is working normally

WiFi light

• Green light off: no communication
• Green flash: wireless transmission is working normally

Power Indicator

• Green light off: Power off
• Green light on: Power on
• Green light flashes: Charging

1. Decrease
2. Shortcut to adjust LED brightness.

Confirm

• Shortcut to switch Speed Alert OOMPH countdown 180s, and the
• original Speed Alert will be restored after 180s

1. Increase
2. Shortcut to adjust volume.

• Long press for 3s to shut down
• Short press to turn on
• Shortcut to enter MENU

Menu

Note: When USB cable connected, battery start charging with icon Tips: When radar control box standby, connecting USB cable will awake the radar control box.

Menu 1:

Step 1: Find “Pair Left” and click OK to choose, press ” ” button to pair the left radar sensor within 60 seconds count down.

Step 2: Press the pairing button on left radar sensor.

Step 3: “pairing successful” appears on display. After pairing, the ID number of the radar sensor will appear in the menu.

OLED Off: Automatic screen off. NOT/10s/20s/30s/60s/90s settable, for example: NOT means the screen always on, 1 Os means screen off after lOs inactivity.

Speed Alert: The minimum speed for the radar detection. There are OOMPH/06PMH/17MPH/37MPH/56MPH settable. If OOMPH is set, the radar will detect the vehicle when the vehicle is stationary. When 17MPH is set, the radar will send out an alarm signal when the vehicle is traveling at a speed greater than 17MPH.

Speed   Unit: MPH/KMH settable.

Menu 2:

Vehicle: The time for the vehicle to stop alarming after it exceeds the radar recognition range. There are CAR/RV1/RV2/RV3/TRUCK1/TRUCK2/TRUCK3, because the length of vehicle varies, so does the time duration for the behind vehicles passing by. We provide multi stop-alarm time for vehicles of different lengths so that users can set according to their situation .

Standby: Radar control box standby interval when no radar signal is received. There are OFF/10MIN/30MIN, for example: OFF means the radar control box will never automatically standby. When set to 10MIN, radar control box will automatically standby after 10 minutes’ no radar signal received.

Reset: restore the default settings (note: the left/right radar sensors will not be reset)

Radar Installation

Before Installation

1. Make sure your vehicle is in a horizontal position
   

2. Tools for Installation
   Find below tools in package box
   

3. Install the radar sensors at corresponding place of the vehicle.

Magnetic Bracket Installation

1. Make sure the metal surface is thicker than 1mm, otherwise the magnet base cannot be fixed firmly.

2. For other materials of vehicle, please use provided metal plate with 3M tape.
   Before putting the metal plate on vehicle, please make sure you wipe off the dust on vehicle surface.

3. Attach the radar sensor to the rear of the vehicle about 50cm to 80cm above the ground as shown in the figure:

4. Clamp the protractor on the radar and turn the radar to make the end of the protractor’s corner is parallel to the vehicle wheel.
   
   

5. Put the horizontal bead on the position of the protractor hole and turn the radar to make the bubble of the horizontal bead is in the middle position.
   

6. Then tighten the screws with the hex key to fix the rotating bracket. Please tighten it symmetrically to avoid changing the radar position.

7. Finally, after the installation of the radars on the left and right sides, it should be as shown in the figure below:
   

Base Installation

1. Locate the punching position by the support cushion (inverted T shape
   as shown in the figure).

2. Unscrew the magnet base of the bracket by loosening the Torx screws
   (as shown in the picture).

3. Fix the bracket on cushion by screws

4. Put back the protective cover on the bracket and tighten with Torx screws.
   

5. Clamp the protractor on the radar and turn the radar to make the end of the protractor’s corner is parallel to the vehicle wheel
   

6. Put the horizontal bead on the position of the protractor hole and turn the radar to make the bubble of the horizontal! bead is in the middle position.
   

7. Then tighten the screws with the hex key to fix the rotating bracket. Please tighten it symmetrically to avoid changing the radar position.

8. Finally, after the installation of the radars on the left and right sides, it should be as shown in the figure below:
   

Radar Control Box Wiring

Trouble shooting

1. If there is no signal on one or both sides, please confirm whether the left/right radar sensor is powered on.

2. If the radar sensor is powered on, the POWER indicator will flash, indicating that it is sending data. (Please pair radar sensor with radar control box first, otherwise, it will have no connection to radar control box).

3. If there is no sound from the external earphone, please check whether the volume is mute.

4. If the device can’t be charged normally, please check whether there is an”H” in the upper left corner on the radar control box, which means that the current battery temperature is too high and you need to wait for it to cool down before resuming charging.

5. If the radar LED indicator does not light up with sound, please confirm whether current driving speed has reached the speed that you set in Speed Alert.

6. If Speed data is missing, please confirm whether your vehicle is able to receive GPS signal.

7. If the charging time is too long or cannot be charged, check the USB cable. It is recommended to use provided charging cable (The normal charging time is about 4-6 hours).

8. If the signal is poor, please make sure the antenna on radar sensors are plugged, and the antenna is placed away from the metal objects.

9. Please make sure that the 2.5mm earphone connector is fully inserted into the hole, otherwise the indicator light may not light up or there may be no sound due to poor contact.
   
   Tips: After plugging in the earphone, press the” @b> ” button to test whether the light or sound is emitted.

10. When working, if either side or both sides of the signal lost for over 1 minute, the device will prompt signal-lost alarm with beeps. Press any button to cancel the beeps.
    When powering on, if only one side of the signal is connected, the device will prompt signal-lost alarm with beeps after 1 minute. Press any button to cancel the beeps.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>