arteconfort Azores Ceiling Fan with Integrated LED Light Instruction Manual
- June 3, 2024
- arteconfort
Table of Contents
arteconfort Azores Ceiling Fan with Integrated LED Light Instruction Manual
THANKS FOR TRUSTING IN ARTECONFORT
Congratulations, you have just purchased an ceiling fan. culling edge technology combined with the highest energy efficiency.
WARNING
Read this 1nstruct1on manual carefully before l,eginnir1g is, nod save ii for future reference In case of transfer of the device, you must also give his inslrucl1on manual lo ice corresponding person.
While using electrical appliances, bc1s1c safety peculium should always be followed lo reduce the risk of fire, electric shock and personal In1ury.
CAUTION
- The product must only be installed by an rnJihori1ed electrician and in compliance will local, regional and state electricity regulations.
- Check if 1l,e electrical of !Iris device are compol1ble will your rnslallai1on
- Turn off the power before installing or repairing the fan.
- The fan must be properly grounded to avoid the risk electric shock.
- Use and unauthored technical rnod1f1cat1011s could suppose a risk of In1ury.
- The Ian must be connected to a 230V 50Hz power supply.
- Do not connect the Ion rotor lo o rnrrenl dimmer. It could give unsatisfactory performance (engine humming) nod Couse engine drone
- Be careful while working near the spIn11Ing blades.
- Never connect the fan to o power point but to the ceiling itself.
- The Ion rn1JSI bee so idol the !,lodes ore at least 2,3 meters oboe the ground
- The fan musk be hung from a structure capable of supporting a weight of at least 50 kg The fixture must be bole to support the weight of the fun in motion nod herald not wobble or loosen.
- Make sure that the blades do not come In will, irislolloiior, sale. Always leave o minimum clearance of 50cm from the tip of the blades to the wall or ceiling.
- Keep in mind that the larger this space, the bel leer the fan’s air flow will be.
- This device is designed for indoor use only Do not use in on open space or where it may be exposed lo wolver or rnoislure,
- The product must only be installed by an rnJihori1ed electrician and in compliance will local, regional and state electricity regulations.
- Check if 1l,e electrical of !Iris device are compol1ble will your rnslallai1on
- Turn off the power before installing or repairing the fan.
- The fan must be properly grounded to avoid the risk electric shock.
- Use and unauthored technical rnod1f1cat1011s could suppose a risk of In1ury.
- The Ian must be connected to a 230V 50Hz power supply.
- Do not connect the Ion rotor lo o rnrrenl dimmer. It could give unsatisfactory performance (engine humming) nod Couse engine drone
- Be careful while working near the spIn11Ing blades.
- Never connect the fan to o power point but to the ceiling itself.
- The Ion rn1JSI bee so idol the !,lodes ore at least 2,3 meters oboe the ground
- The fan musk be hung from a structure capable of supporting a weight of at least 50 kg The fixture must be bole to support the weight of the fun in motion nod herald not wobble or loosen.
The instructions and safety regulations In this manual cannoli prevent olla conditions nod s1lual1ons 1h01 may occur. For obvious reasons, this manual cannot include factors such as caution nod core These factors must be assumed by who installs, maintains, uses and en1oys the product.
BEFORE INSTALLATION
Open the box avoiding the use of blondes or “cutters” to avoid scratching the fan components.
Unpack the parts handling them carefully so that they do not bend or scratch, and place the motor on a cloth or a soft surface to prevent damage (you can also use the anti-shock foam on the box for this purpose). Never support the motor sideways.
It is advisable to mount the fan on the floor or a surface large enough so that no component falls.
Identify all parts before beginning assembly.
TOOLS NEEDED
*Not included. It is recommended that the screwdriver be magnetized.
MAINTENANCE
- Over time and due to the natural movement of the fan, some connections may come loose. Check the support connections, brackets and attach the blades twice a year, and make sure they are firm.
- Clean the appliance regularly to maintain its appearance as new. To do this, use a soft, lint free cloth to avoid scratching the finish. Never use water, because it could damage the motor or the wood of the blades.
- It is not necessary to grease the fan, since the motor bearings permanently contain lubricant.
WARRANTY
You can check the warranty for this product on its corresponding page at the end of this manual.
ENVIRONMENT
Do not throw electrical appliances into the household waste, use selective collection facilities. Consult local authorities for more information.
If electrical appliances are deposited in landfills, hazardous components can seep into groundwater and enter the food chain, damaging health and well- being.
Thanks for taking care of the environment.
This product contains a light source of energy efficiency class D – (EU) 2019/2015
PROBLEM SOLVING
Before carrying out the clerks deloused below, I1,e fan must be w1lhoul power supply.
1. The fan does not start
- Replace the remote control batteries 1f they are exhausted or nil sailable.
- Check thot there are no nearby devices that Moy be causing 1nlerference will lee remote or reducing signal reception
- Resynchronize the remote control.
- Check thot the electrical conations ore com t must be corned out by licensed electrician).
- Check fuses nod swild1es, loll Iffier hoes voltage and 1t reaches the fan.
2. The fan makes executive noise while rotating
- Allow o slight fallen the canopy and the ceiling, prevent mg them from touching direly.
- Check that the f1x1ng screws of the blades, the fixing screws to the roof, the stem and the fastening rents ore correctly tightened
- If you replaced the original remote control or receiver, reins loll Iffier supplied ones oolong will the fan.
3. The fan wobbles
- Check that the f1x111g screws of the blades, ilk laxing sews lo the roof, I he: stern cod I he fastening elements are correctly tightened.
- Check that lye blades ore nil deformed and follow the blade balancing instructions detailed in this manual.
4. The air flow is insufficient
- Check that the slight fallen the canopy and the ceiling, prevent mg them from touching direly.
- Check that the f1x1ng screws of the blades, the fixing screws to the roof, the stem and the fastening rents ore correctly tightened
- If you replaced the original remote control or receiver, reins loll Iffier supplied ones oolong will the fan.
5. The light does not turn on
- Check the bulb is not blown, otherwise replaces It with o new one
- If your fern has LED light included, check the me p1operly laxed according instruction manual.
BALANCING OF BLADES
The boon ing of I he fun is noel o sign of malfuncl1on Before balancing, and always w1lh the fan off, check the fastening of the blades one thot they do not show deformations Once checked, 1f evei’yth1ng IS correct, proceed to the of I he lodes:
1.Select the blade to balance
Put the clip included In the center of a blade. Next, turn on the fan and, if
the balancing persists, put the clip on on other blade 1,nt,I the sw111g
decreases. In this way, the selected blade will be lye one 11101 need, lee
cou11lerweighl
2. Find thot equilibrium point
Place the clip on the blade you have previously selected mid lay Iffier best
place lo place ii (frown the center to the tip of the blade) until the wobble
disappears.
3. Check the correct balance
Glue the counterweight to the height of the clip on the surface of the blade.
Remove the clip, and turn on the fan Check if it continues to wobble, if so,
place another counterweight. 11 ii gels worse, you to place it
REMOTE CONTROL
The remote control works at 433 Hz radio frequency and includes an LCD screen that shows the deferent functions of the fan.
BREEZE MODE
Turn on the breeze mode that smoothly alternates between fast and slow speeds
(speed l to 3) to create a greater sense of comfort.
- Turn on the breeze mode: switch on the fan pressing the “ON/ OFF” button then press the “Breeze mode” button.
- LCD screen off (standby): pressing the button once will activate the LCD screen showing that the breeze mode is on.
- Cancel breeze mode: press the “breeze mode” button again and the fan will return to the rotation speed selected before the breeze mode. You can also press the “ON / OFF” button of the fan to stop the rotation of the blades, when you turn it on again it will not remember the breeze mode, and it will continue working on the previously selected rotation speed .
PROGRAMMING
Sets the operation hours of the fan (9 levels in periods of This does not act
the fan light.
- Turn on the programming mode: pressing the button, each press will add one extra level of programming up to 9 hours.
- LCD screen off (standby): pressing the button once will activate the LCD screen showing the programmed operating time.
- Cancel programming: press the “Program” button until you reach level 0 or keep the button pressed for 2 seconds. If you turn o the fan while is programmed when you turn it on again it will not remember the programming time.
REMOTE CONTROL SYNCHRONIZATION
It allows you to synchronize the remote control with your fan if the synchronization has been lost (it is not necessary to synchronize it on the rest use of the fan) or to use a remote control with several fans at the same time. For further information look at the section “CONTROL SYNCHRONIZATION” below.
- To synchronize: press for 3 seconds within 10 seconds after connecting the power.
WINTER/SUMMER MODE
Reverses the direction of rotation of the blades to change to summer mode
(turn to the left, counterclokwise) or winter mode (turn to the right,
clockwise).
- Change mode: press the “Winter / summer mode” button for 2 seconds and wait for the fan to stop completely. After 5 seconds the fan will automatically turn on spinning in the opposite direction.
- LCD screen a (standby}: pressing the button once will activate the LCD screen showing the selected rotation mode.
ON/OFF FAN
Turn the fan on and off.
- Turn on and off: by short pressing. The fan will remember the last selected level before turning it off.
- LCD screen off (standby): pressing the button once will activate the LCD screen showing the level of rotation speed.
- Control remote priority: if you press the wall switch while the fan is o, when it gets connect again it will remember the command that was given by the remote control.
SPEED
Select the speed of the blades rotation (6 levels).
- Change speed: increase or decrease the speed of the blades by clicking on the “arrow” button. Is not possible to change the speed when the “Breeze tv1ode” is on.
- Control remote priority: if you press the wall switch while the fan is o, when it gets connect again it will remember the command that was given by the remote control.
ON/OFF LIGHT
Turn the light on and off.
- Turn on and off the light: by short pressing. It will remember the last selected level before turning it off.
- LCD screen o (standby}: pressing the button once will activate the LCD screen showing the level of light intensity.
- Control remote priority: if you press the wall switch while the fan is o, when it gets connect again it will remember the command that was given by the remote control.
DIMMER
It increase or decrease the light intensity (up to 8 levels).
- Change intensity: increase or decrease the the light intensity by pressing on the “arrows· buttons.
- Control remote priority: if you press the wall switch while the fan is o, when it gets connect again it will remember the command that was given by the remote control.
COLOUR TEMPERATURE
It select the desired color temperature (warm, neutral or cool light).
- To change the light temperature: press the button indicated with the color of each temperature.
COLOR TEMPERATURE MEMORY
The fan has color temperature memory of the light. This function allows you to maintain the same color temperature when the fan light is turned on again.
To change the color temperature of the light press the button indicated with
the color of each color temperature.
When you turn the light off and turn it on again it will keep the selected
temperature.
BATTERIES
The remote control batteries are not included. The required battery model is
2x AAA.
*Remove the batteries from the controller if it is not going to be used for a long time.
REMOTE CONTROL SYNCHRONIZATION
The remote control is synchronized from the factory, you only need to re- synchronize it if the synchronization has been lost, if you purchased o new one or want to control several funs with a single remote.
A REMOTE CONTROL TO A FAN
(Example for two fans, applicable to a larger number of fans)
   
SPARE PARTS
You con request speared parts by going lo the sloe where you purchased it or to any another of the brand If the product is under warranty, present the purchase receipt or Invoice.
WARRANTY
The motor of this fan is guaranteed for 5 years and 3 years for the rest of
the components. This warranty covers the exchange or repair of any failure or
defect of the device, provided that it is due to a manufacturing fault or a
defective component.
IMPORTANT
It is essential for the use of this guarantee to prove the purchase date of
the product. Therefore, it will be necessary to present the purchase receipt
as well as this instruction manual.
⚠ Keep the purchase receipt and the instruction manual.
The warranty of this product does not apply if the defects of the device have been caused by:
- Damage during transport not carried out by the manufacturer. (Example: dents, components or glass pieces damages … )
- Carrying out incorrect installations or assemblies.
- Poor preservation of the product.
- Damage caused by contact of the device with chemical or inappropriate substances. This fan is designed for indoor use only, so it should not be exposed to water and / or humidity either.
- The replacement or use of additional parts or accessories that are not original from the manufacturer.
- When using a control through a wall dimmer other than the remote control supplied with the fan.
Before calling for technical assistance, it is advisable to read the troubleshooting guide included in this manual.
If you have any questions, problems or missing components, consult your
dealer. You can also contact us through the email
info@arteconfort.com or through the contact
form available on our website.
ARTECONFORT I IOTEL SL.
Cira Andaluda, 6
45’2’24 Sesena N uevo
Toledo, Espoiia
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>