arteconfort Altea Ceiling Fan with Integrated LED Light Instruction Manual
- June 3, 2024
- arteconfort
Table of Contents
Altea Ceiling Fan with Integrated LED Light Instruction Manual
THANKS FOR TRUSTING IN ARTECONFORT
Congratulations, you have just purchased an Artecontort ceiling fan: cutting edge technology combined with the highest energy efficiency.
WARNING
Read this instruction manual carefully before beginning installation and save
it for future reference. In case of transfer of the device, you must also give
this instruction manual to the corresponding person.
While using electrical appliances, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and personal injury.
CAUTION
-
The product must only be installed by an authorized electrician and in compliance with local, regional and state electricity regulations.
-
Check if the electrical specifications of this device are compatible with your installation.
-
Turn off the power before installing or repairing the fan.
-
The fan must be properly grounded to avoid the risk of electric shock.
-
Use and unauthorized technical modifications could suppose a risk of injury.
-
The fan must be connected to a 230V 50Hz power supply.
-
Do not connect the fan motor to a current dimmer. It could give unsatisfactory performance (engine humming) and cause engine damage.
-
Be careful while working near the spinning blades.
-
Never connect the fan to a power point but to the ceiling itself.
-
The fan must be installed so that the blades are at least 2,3 meters above the ground.
-
The fan must be hung from a structure capable of supporting a weight of at least 50 kg. The fixture must be able to support the weight of the fan in motion and should not wobble or loosen.
-
Make sure that the blades do not come in contact with any object at the installation site.
Always leave a minimum clearance of 50cm from the tip of the blades to the wall or ceiling.
Keep in mind that the larger this space, the better the fan’s air flow will be. -
This device is designed for indoor use only. Do not use in an open space or where it may be exposed to water or moisture.
-
Never install the appliance in a room with a high degree of humidity.
-
The fan must not be started in a room with a gas appliance running at the same time.
-
This device can be used by children aged 8 years and above and of people with reduced physical, sensory or mental abilities or lack of experience and knowledge if they are supervised or instructed about the use of the device safely and understand the risks involved. As well as cleaning and maintenance of the device.
-
Children should not play with the device.
-
Before reversing the direction of rotation of the blades stop the fan completely. This will prevent any damage to the fan motor or controller (if installed).
-
Do not insert any object into the fan blades while they are rotating. This can damage them and alter the balance of the fan and the device can fall down.
-
After the fan is fully installed make sure all fasteners are securely fastened to prevent any wobbling or falling of the machine.
The instructions and safety regulations in this manual cannot prevent all conditions and situations that may occur. For obvious reasons, this manual cannot include factors such as caution and care. These factors must be assumed by who installs, maintains, uses and enjoys the product.
BEFORE INSTALLATION
Open the box avoiding the use of blades or “cutters” t o avoid scratching the
fan components.
Unpack the parts handling them carefully so that they do not bend or scratch,
and place the motor on a cloth or a soft surface t o prevent damage (you can
also use the anti- shock foam on the box for this purpose). Never support the
motor sideways.
It is advisable t o mount the fan on the floor or a surface large enough so
that no component falls. Identify all parts before beginning assembly.
TOOLS NEEDED
*Not included.
Itis recommended that the screwdriver be magnetized.
MAINTENANCE
- Over time and due to the natural movement of the fan, some connections may come loose.
- Check the support connections, brackets and attach the blades twice a year, and make sure they are firm.
- Clean the appliance regularly to maintain its appearance as new. To do this, use a soft, lint- free cloth to avoid scratching the finish. Never use water, because it could damage the motor or the wood of the blades.
It is not necessary t o grease the fan, since the motor bearings permanently contain lubricant.
WARRANTY
You can check the warranty for this product on its corresponding page at the
end of this manual.
ENVIRONMENT
Do not throw electrical appliances into the household waste, use selective
collection facilities. Consult local authorities for more information.
If electrical appliances are deposited in landfills, hazardous components can
seep into groundwater and enter the food chain, damaging health and well-
being.
Thanks for taking care of the environment.
This product contains a light source of energy efficiency class F – ( E U )
2019/2015
PROBLEM SOLVING
Before carrying out the checks detailed below, the fan must be without power supply.
1. The fan does not start
-
Replace the remote control batteries if they are exhausted or not suitable.
-
Check that there are no nearby devices that may be causing interference with the remote or reducing signal reception.
-
Resynchronize the remote control.
-
Check that the electrical connections are correct (must be carried out by a licensed electrician).
-
Check fuses and switches, that the installation has voltage and it reaches the fan.
2.The fan makes excessive noise while rotating -
Allow a slight separation between the canopy and the ceiling, preventing them from touching directly.
-
Check that the fixing screws are correctly tightened.
-
If you replaced the original remote control or receiver, reinstall the supplied ones along with the fan.
3. The fan wobbles -
Check that the fixing screws are correctly tightened.
4. The air flow is insufficient -
Check that the blades rotate in the correct direction (Summer / Winter).
-
Avoid nearby objects that may impede air circulation.
-
Verify that the diameter of the blades of your fan is sufficient for the area of the room in which it is installed.
5. The light does not turn on -
Check the bulb is not blown, otherwise replaces it with a new one.
If your fan has LED light included, check the connections are properly fixed according to the instruction manual.
REMOTE CONTROL
FAN ON/OFF
Turn the fan on or off.
LIGHT A ON/OFF
Turn the light A on or off.
LIGHT A COLOR TEMPERATURE
Changes the color temperature of the light A.
LIGHT B ON/OFF
Turn the light B on or off. Changes the color temperature of the light B
turning off and turning on again the light within 2 seconds.
LIGHT A INTENSITY DIMMER
Increase or decrease the intensity of the light A.
TIMER
Set the hours of operation of the fan (2, 4 or 8 hours).
SPEED
Select the rotation speed of the fan blades.
BREEZE MODE
T urn on the breeze mode that smoothly alternates between fast and slow
speeds.
The remote control is synchronized from the factory, you only need to re-
synchronize it if the synchronization has been lost. if you purchased a new
one or want to control several fans with a single remote.
COLOR TEMPERATURE MEMORY
The fan has color temperature memory of the light. This function a llows you
to maintain the same color temperature when the fan light is turned on again.
To change the color temperature of the light press the button indicated with
the color of each color temperature.
When you turn the light off and turn it on again it will keep the selected
temperature.
BATTERIES
The remote control batteries are not included.
The required battery model i s 2xAAA.
*Remove the batteries from the controller if it is not going t o be used for a long time.
REMOTE CONTROL SYNCHRONIZATION
The remote control is synchronized from the factory, you only need to re- synchronize it if the synchronization has been lost , if you purchased a new one or want t o control several fans with a single remote.
A REMOTE CONTROL TO A NEW FAN
-
Cut the current
Be sure t o cut off the current until the fan stop. -
Restore the current
Re – establish the current. -
3 . Synchronize the remote control
Within 5 seconds , press the ” button for a few seconds until you hear the signal. Control range: 8-10m.
A REMOTE CONTROL TO VARIOUS FANS
-
Cut the current
Be sure t o cut off the current until all fans stop . -
Restore the current
Re-establish the current. -
Synchronize the remote control
Within 5 seconds, press the “ butten on each fan for a few seconds until you hear the signal. If they are within a radius of less than 10m (control range: 8-10m), all will synchronize at the same time.
A REMOTE CONTROL TO A FAN
(Example for two fans, applicable to a larger number of fans)
-
Cut the fan A current*
Be sure to cut the fan A current (the one we want to remove the synchronization ) . -
Cut the fan B current*
Be sure to cut off fan B (the one we want to synchronize). -
Restore fan B current
When you restore the fan B , press the button within 5 seconds until you hear the signal t o synchronize remote control B with fan B. -
Cut the fan B current*
Be sure t o cut the fan B current. -
Restore the fan A current
When you restore the fan A press the button within 5 seconds until you hear the signal to synchronize remote control A with fan A. -
Repeat the steps Repeat steps with each fan you have and want to individualize its remote control.
*To cut the current you can press the individual fan switch. If there is not, disconnect the quick connect cables from the fan.
SPARE PARTS
You can request spare parts by going t o the store where you purchased it or
to any another of the brand. If the product is under warranty, present the
purchase receipt or invoice.
DESCRIPTION | REFERENCE |
---|---|
Short LED strip | LEDALTEAC |
Long LED strip | LEDALTEAL |
Remote control | MANALTEAONLY |
Driver | CONALTEAONLY |
WARRANTY
The motor of this fan is guaranteed for 5 years and 3 years for the rest of
the components. This warranty covers the exchange or repair of any failure or
defect of the device, provided that it is due to a manufacturing fault or a
defective component.
IMPORTANT
It is essential for the use of this guarantee to prove the purchase date of
the product. Therefore, it will be necessary to present the purchase receipt
as well as this instruction manual. Keep the purchase receipt and the
instruction manual.
The warranty of this product does not apply if the defects of the device have
been caused by:
-
Damage during transport not carried out by the manufacturer. (Example: dents, components or glass pieces damages …)
‘Carrying out — incorrect installations — or assemblies. -
Poor preservation of the product.
-
Damage caused by contact of the device with chemical or inappropriate substances. This fan is designed for indoor use only, so it should not be exposed to water and / or humidity either.
-
The replacement or use of additional parts or accessories that are not original from the manufacturer.
-
When using a control through a wall dimmer other than the remote control supplied with the fan.
Before calling for technical assistance, it is advisable to read the troubleshooting guide included in this manual.
If you have any questions, problems or missing components, consult your
dealer.
You can also contact us through the email
info@arteconfort.com or through the contact
form available on our website.
www.arteconfort.com
ARTECONFORT HOTEL S.L.
Ctra. Andalucia, 6
45994 Sesefia Nuevo
Toledo, Espafia
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>