arteconfort AZORES CEILING FAN Instruction Manual

arteconfort AZORES CEILING FAN Instruction Manual

THANKS FOR TRUSTING IN ARTECONFORT

Congratulations, you have just purchased an Arteconfort ceiling fan: cutting edge technology combined with the highest energy efficiency.

WARNING
Read this instruction manual carefully before beginning installation and save it for future reference. In case of transfer of the device, you must also give this instruction manual to the corresponding person.

While using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury.

CAUTION

• The product must only be installed by an authorized electrician and in compliance with local, regional and state electricity regulations.

• Check if the electrical specifications of this device are compatible with your installation.

• Turn off the power before installing or repairing the fan.

• The fan must be properly grounded to avoid the risk of electric shock.

• Use and unauthorized technical modifications could suppose a risk of injury.

• The fan must be connected to a 230V 50Hz power supply.

• Do not connect the fan motor to a current dimmer. It could give unsatisfactory performance (engine humming) and cause engine damage.

• Be careful while working near the spinning blades.

• Never connect the fan to a power point but to the ceiling itself.

• The fan must be installed so that the blades are at least 2,3 meters above the ground.

• The fan must be hung from a structure capable of supporting a weight of at least 50 kg. The fixture must be able to support the weight of the fan in motion and should not wobble or loosen.

• Make sure that the blades do not come in contact with any object at the installation site. Always leave a minimum clearance of 50cm from the tip of the blades to the wall or ceiling.
  Keep in mind that the larger this space, the better the fan’s air flow will be.

• This device is designed for indoor use only. Do not use in on open space or where it may be exposed to water or moisture.

• Never install the appliance in a room with a high degree of humidity.

• The fan must not be started in a room with o gas appliance running at the some time.

• This device can be used by children aged 8 years and above and of people with reduced physical, sensory or mental abilities or lack of experience and knowledge if they are supervised or instructed about the use of the device safely and understand the risks involved. As well os cleaning and maintenance of the device.

• Children should not play with the device.

• Before reversing the direction of rotation of the blades stop the fan completely. This will prevent any damage to the fan motor or controller (if installed).

• Do not insert any object into the fan blades while they are rotating. This can damage them and alter the balance of the fon and the device con loll down.

• After the fan is fully installed make sure all fasteners are securely fastened to prevent any wobbling or falling of the machine.

The instructions and safety regulations in this manual cannot prevent all conditions and situations that may occur. For obvious reasons, this manual cannot include factors such os caution and core. These factors must be assumed by who installs, maintains, uses and enjoys the product.

BEFORE INSTALLATION

Open the box avoiding the use of blades or “cutters’ to ovoid scratching the fan components.

Unpack the ports handling them carefully so that they do not bend or scrotch, and place the motor on a cloth or o soft surface to prevent damage (you can also use the anti-shock foam on the box for this purpose). Never support the motor sideways.

It is advisable to mount the fan on the floor or a surface large enough so that no component falls.

Identify all ports before beginning assembly.

TOOLS NEEDED

Not included. It is recommended that the screwdriver be magnetized.

MAINTENANCE

• Over time and due to the natural movement of the fan, some connections may come loose. Check the support connections, brackets and attach the blades twice a year, and make sure they are firm.
• Clean the appliance regularly to maintain its appearance as new. To do this, use a soft, lint-free cloth to avoid scratching the finish. Never use moter, because it could damage the motor or the wood of the blades.
• It is not necessary to grease the fan, since the motor bearings permanently contain lubricant.

WARRANTY

You can check the warranty for this product on its corresponding page at the end of this manual.

ENVIRONMENT

Do not throw electrical appliances into the household waste, use selective collection facilities. Consult local authorities for more information.

If electrical appliances are deposited in landfills, hazardous components can seep into groundwater and enter the food chain, damaging health and well- being.

Thanks for taking core of the environment.

This product contains a light source of energy efficiency class D – (EU) 2019/2015

PROBLEM SOLVING

Before carrying out the checks detailed below, the fan must be without power supply.

The fan does not start

• Replace the remote control batteries if they are exhausted or not suitable.
• Check that there are no nearby devices that may be causing interference with the remote or reducing signal reception.
• Resynchronize the remote control.
• Check that the electrical connections are correct (must be carried out by a licensed electrician).
• Check fuses and switches, that the installation has voltage and it reaches the fan.

The fan makes excessive noise while rotating

• Allow a slight separation between the canopy and the ceiling, preventing them from touching directly.
• Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
• If you replaced the original remote control or receiver, reinstall the supplied ones along with the fan.

The fan wobbles

• Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
• Check that the blades are not deformed and follow the blade balancing instructions detailed in this manual.

The air flow is insufficient

• Check that the blades rotate in the correct direction (Summer / Winter).
• Avoid nearby objects that may impede air circulation.
• Verify that the diameter of the blades of your fan is sufficient for the area of the room in which it is installed.

The light does not turn on

• Check the bulb is not blown, otherwise replaces it with a new one.
• If your fan has LED light included, check the connections are properly fixed according to the instruction manual.

BALANCING OF BLADES

The balancing of the fan is not a sign of malfunction. Before balancing, and always with the fan off, check the fastening of the blades and that they do not show deformations. Once checked, if everything is correct, proceed to the balancing of the blades:

1. Select the blade to balance
   Put the clip included in the center of a blade. Next, turn on the fan and, if the balancing persists, put the clip on another blade until the swing decreases. In this way, the selected blade will be the one that needs the counterweight.
   

2. Find the equilibrium point
   Place the clip on the blade you hove previously selected and try the best place to place it (from the center to the tip of the blade) until the wobble disappears.

3. Check the correct balance
   Glue the counterweight to the height of the clip on the surface of the blade. Remove the clip, and turn on the fan. Check if it continues to wobble, if so, place another counterweight. If it gets worse, you should try another better area to place it.
   

REMOTE CONTROL

The remote control works at 433MHz radio frequency and includes an LCD screen that shows the dierent functions of the fan.

BREEZE MODE
Turn on the breeze mode that smoothly alternates between fast and slow speeds (speed 1 to 3) to create a greater sense of comfort.

• Turn on the breeze mode: switch on the fan pressing the ON / OFF button then press the “Breeze mode” button.
• LCD screen off (standby): pressing the button once will activate the LCD screen showing that the breeze mode is on.
• Cancel breeze mode: press the “breeze mode” button again and the fan will return to the rotation speed selected before the breeze mode. You can also press the “ON / OFF” button of the fan to stop the rotation of the blades, when you turn it on again it will not remember the breeze mode, and it will continue working on the previously selected rotation speed..

LCD sequence

PROGRAMMING
Sets the operation hours of the fan (9 levels in periods of 1h). This does not aect the fan light.

• Turn on the programming mode: pressing the button, each press will add one extra level of programming up to 9 hours.
• LCD screen off (standby): pressing the button once will activate the LCD screen showing the programmed operating time.
• Cancel programming: press the “Program” button until you reach level 0 or keep the button pressed for 2 seconds. If you turn o the fan while is programmed when you turn it on again it will not remember the programming time.

LCD sequence

REMOTE CONTROL SYNCHRONIZATION
It allows you to synchronize the remote control with your fan if the synchronization has been lost (it is not necessary to synchronize it on the rst use of the fan) or to use a remote control with several fans at the same time. For further information look at the section “CONTROL SYNCHRONIZATION” below.

• To synchronize: press for 3 seconds within 10 seconds after connecting the power.

LCD sequence

WINTER/SUMMER MODE
Reverses the direction of rotation of the blades to change to summer mode (turn to the left, counterclockwise) or winter mode (turn to the right, clockwise).

• Change mode: press the “Winter / summer mode” button for 2 seconds and wait for the fan to stop completely. After 5 seconds the fan will automatically turn on spinning in the opposite direction.
• LCD screen o (standby): pressing the button once will activate the LCD screen showing the selected rotation mode.

LCD sequence

ON/OFF FAN
Turn the fan on and off.

• Turn on and off: by short pressing. The fan will remember the last selected level before turning it off.
• LCD screen off (standby): pressing the button once will activate the LCD screen showing the level of rotation speed.
• Control remote priority: if you press the wall switch while the fan is o, when it gets connect again it will remember the command that was given by the remote control.

SPEED
Select the speed of the blades rotation (6 levels).

• Change speed: increase or decrease the speed of the blades by clicking on the “arrow” button. Is not possible to change the speed when the “Breeze Mode” is on.
• Control remote priority: if you press the wall switch while the fan is o, when it gets connect again it will remember the command that was given by the remote control.

LCD sequence

ON/OFF LIGHT
Turn the light on and off.

• Turn on and off the light: by short pressing. It will remember the last selected level before turning it off.
• LCD screen o (standby): pressing the button once will activate the LCD screen showing the level of light intensity.
• Control remote priority: if you press the wall switch while the fan is o, when it gets connect again it will remember the command that was given by the remote control.

DIMMER
It increase or decrease the light intensity (up to 8 levels).

• Change intensity: increase or decrease the the light intensity by pressing on the “arrows’ buttons.
• Control remote priority: if you press the wall switch while the fan is o, when it gets connect again it will remember the command thot wos given by the remote control.

LCD sequence

COLOUR TEMPERATURE
It select the desired color temperature (warm, neutral or cool light).

• To change the light temperature: press the button indicated with the color of each temperature.

COLOR TEMPERATURE MEMORY

The fan has color temperature memory of the light. This function allows you to maintain the same color temperature when the fan light is turned on again.

To change the color temperature of the light press the button indicated with the color of each color temperature.

When you turn the light off and turn it on again it will keep the selected temperature.

BATTERIES

The remote control batteries are not included. The required battery model is 2x AAA.

*Remove the batteries from the controller if it is not going to be used for a long time.

REMOTE CONTROL SYNCHRONIZATION

The remote control is synchronized from the factory, you only need to resynchronize it if the synchronization has been lost, if you purchased a new one or want to control several fans with a single remote.

A REMOTE CONTROL TO A NEW FAN

1. Cut the current
   Be sure to cut off the current until the fan stop.
   

2. Restore the current
   Re-establish the current.
   

3. Synchronize the remote control
   Within 10 seconds, press the synchronization button “ ” during 3 seconds until you hear the signal. Control range: 8.10m.

A REMOTE CONTROL TO VARIOUS FANS

1. Cut the current
   Be sure to cut off the current until all fans stop.

2. Restore the current
   Re-establish the current.
   

3. Synchronize the remote control
   Within 10 seconds, press the synchronization button “ ” on each fon during 3 seconds until you hear the signal. If they are within a radius of less than 10m (control range: 8-10m), all will synchronize of the same time.
   

A REMOTE CONTROL TO A FAN

(Example for two fans, applicable to o larger number of fans)

1. Cut the fan A current’
   Be sure to cut the fan A current (the one we want to remove the synchronization).
   

2. Cut the fan B current’
   Be sure to cut off fan B (the one we wont to synchronize).
   

3. Restore fan B current
   When you restore the fan B and within 10 seconds, press the synchronization button “ ” during 3 seconds until you hear the signal to synchronize remote control B with fan B.
   

4. Cut the fan B current’
   Be sure to cut the fan B current.
   

5. Restore the fan
   A current When you restore the fan A and within 10 seconds, press the synchronization button “ ” during 3 seconds until you hear the signal to synchronize remote control A with fan A.
   

6. Repeat the steps
   Repeat steps with each fan you hove and want to individualize its remote control.
   

*To cut the current you can press the individual fan switch. If there is not, disconnect the quick connect cables from the fan.

SPARE PARTS

You can request spare parts by going to the store where you purchased it or to any another of the brand. If the product is under warranty, present the purchase receipt or invoice.

WARRANTY

The motor of this fan is guaranteed for 5 years and 3 years for the rest of the components. This warranty covers the exchange or repair of any failure or defect of the device, provided that it is due to a manufacturing fault or a defective component.

IMPORTANT
It is essential for the use of this guarantee to prove the purchase date of the product. Therefore, it will be necessary to present the purchase receipt as well as this instruction manual.

Keep the purchase receipt and the instruction manual.

The warranty of this product does not apply if the defects of the device have been caused by:

• Damage during transport not carried out by the manufacturer. (Example: dents, components or glass pieces damages …)
• Carrying out incorrect installations or assemblies.
• Poor preservation of the product.
• Damage caused by contact of the device with chemical or inappropriate substances. This fan is designed for indoor use only, so it should not be exposed to water and / or humidity either.
• The replacement or use of additional parts or accessories that are not original from the manufacturer.
• When using a control through a wall dimmer other than the remote control supplied with the fan.

Before calling for technical assistance, it is advisable to read the troubleshooting guide included in this manual.

If you have any questions, problems or missing components, consult your dealer. You can also contact us through the email info@arteconfort.com or through the contact form available on our website.

www.arteconfort.com
ARTECO\ FORT HOTEL S.L.
Ctra. Anc alucia, 6
45224 Sesena \uevo
Toleco, Espana

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>