CYP PUV-1710L-AVLC-KIT HDR Transmitter and Receiver Instruction Manual

: September 30, 2024
: CYP

Table of Contents

CYP PUV-1710L-AVLC-KIT HDR Transmitter and Receiver
FAQs
SAFETY PRECAUTIONS
INTRODUCTION
APPLICATIONS
PACKAGE CONTENTS
SYSTEM REQUIREMENTS
FEATURES
OPERATION CONTROLS AND FUNCTIONS
CONNECTION DIAGRAM
SPECIFICATIONS
ACRONYMS
CONTACT INFORMATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CYP PUV-1710L-AVLC-KIT HDR Transmitter and Receiver

FAQs

Q: What type of HDMI cables are recommended for use with this product?

A: Premium High-Speed HDMI cables are highly recommended for optimal performance.

Q: How far can the transmitter and receiver be placed from each other?

A: The transmission distance is up to 70 meters.

DISCLAIMERS

The information in this manual has been carefully checked and is believed to be accurate. CYP (UK) Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be contained in this document. CYP (UK) Ltd also makes no commitment to update or to keep current the information contained in this document. CYP (UK) Ltd reserves the right to make improvements to this document and/or product at any time and without notice.

COPYRIGHT NOTICE

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means—electronic, mechanical, magnetic, optical, chemical, manual, or otherwise without express written permission and consent from CYP (UK) Ltd. © Copyright 2011 by CYP (UK) Ltd. All Rights Reserved. Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install, or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment:

Always follow basic safety precautions to reduce the risk of fire, electrical shock, and injury to persons.
To prevent fire or shock hazards, do not expose the unit to rain, or moisture or install this product near water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
Do not attach the power supply cabling to building surfaces.
Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person to walk on it.
To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO.	DATE	SUMMARY OF CHANGE
v1.00	16/03/2018	First release

INTRODUCTION

This transmitter and receiver set is a great solution for extending UHD video and audio as well as Ethernet and control via a single run of Cat.5e/6/7 cable over distances up to 70 metres. This extender set complies with the advanced HDCP 2.2 and HDMI 2.0 standards, as well as supporting the legacy HDCP 1. x and HDMI 1. x standards. Despite HDBaseT’s 10.2Gbps bandwidth limitation, 4K UHD HDMI video sources, up to and including 4K@60Hz (4:4:4, 8-bit) as well as 10/12-bit sources with HDR, are able to be processed and extended by the use of AVLC (Adaptive Visually Loss-less Compression) when needed. Multiple data and control interfaces are also provided, including IR and RS-232 connections. The Receiver (PD) is powered by 48V PoH (Power over HDBaseT) provided by the Transmitter (PSE), allowing for greater flexibility within different installation scenarios.

APPLICATIONS

Household entertainment sharing and control Lecture room display and control
Showroom display and control
Meeting room presentation and control Classroom display and control

PACKAGE CONTENTS

1×HDMI to Cat.5e/6/7 Transmitter (with IR & RS-232) 1×Cat.5e/6/7 to HDMI Receiver (with IR & RS-232) 1×48V/0.83A DC Power Adapter
1×3.5mm to IR Extender Cable
1×3.5mm to IR Blaster Cable
1×Operation Manual

SYSTEM REQUIREMENTS

HDMI source equipment such as a media player, video game console, or set-top box.
HDMI receiving equipment such as an HDTV, monitor or audio amplifier.
The use of “Premium High-Speed HDMI” cables, and industry-standard Cat.6, Cat.6a, or Cat.7, is highly recommended.

FEATURES

HDMI with HDR, 3D & 4K@60Hz support, DVI 1.0 compatible
HDCP 2.2 and HDCP 1.x compliant
Supports up to 4K UHD (18Gbps, 4K@50/60Hz 4:4:4, 8-bit) video input Supports output resolutions up to 4K@50/60Hz (4:4:4, 8-bit) Supports Deep Colour input and output up to 12-bit
Supports 10-bit and 12-bit HDR bypass
Supports CEC bypass
Simultaneous transmission of video, audio, and data over a single Cat.5e/6/7 cable up to 70m (230ft) at 1080p and 35m (115ft) at 4K Supported HDBaseT feature set: HD Video & Audio, 48V PoH, and Control (Bi-directional IR/RS-232 pass-through)
Integrated AVLC (Adaptive Visually Lossless Compression) activates when the bandwidth requirements of the source are beyond 10.2Gbps (340MHz) allowing for support of sources up to 18Gbps (600MHz) with no loss of visual quality
The AVLC function allows manual selection between High Quality (Full bandwidth) mode and Standard mode (Lower bandwidth, useful for longer cable runs with 4K sources)
Supports standard IEEE 802.3 AT 48V PoH from Transmitter (PSE) to Receiver (PD) (compatible Receivers only)

Note : The 48V PoH function is designed for powering compatible Receiver units only. Non-PoH Receivers will need their own power supply. Receivers from other brands may not be compatible.

OPERATION CONTROLS AND FUNCTIONS

Transmitter’s Front Panel

STD/HQ: This switch allows the user to select which compression mode to use when AVLC is active. HQ (High Quality) mode uses the least amount of compression and provides the highest possible visual quality (perceptually identical to the original). STD (Standard Quality) mode applies additional signal reduction methods to lower the bandwidth requirements of 4K sources further, improving transmission reliability over longer cable runs at the cost of some visual fidelity.
ISP: This button is reserved for factory use only.
STD/UPDATE: This switch is reserved for factory use only. The default setting is “STD”.
RS-232 IN: Connect to a PC, laptop, or other serial control device for the extension of RS-232 signals.
SYNC LED: This LED will illuminate when a live input source is detected.
- HQ/STD LED: This LED will illuminate whenever the AVLC function is active. A green LED indicates that AVLC is in HQ (High Quality) mode. A red LED indicates that AVLC is in STD (Standard) mode.
- POWER LED: This LED will illuminate to indicate the unit is on and receiving power.
- LINK LED: This LED will illuminate solidly when a live connection with a compatible Receiver is active. The LED will blink with a regular pattern if a Receiver is connected but there is not currently a live signal. The LED will blink with an irregular pattern if a connection error has occurred.

Transmitter’s Rear Panel

DC 48V: Plug the 48V DC power adapter into this port and connect it to an AC wall outlet for power.
IR1 BLASTER: Connect to the provided IR Blaster to transmit IR signals to devices within direct line-of-sight of the IR Blaster.
IR2 EXTENDER: Connect to the provided IR Extender to extend the IR control range of remotely located devices. Ensure that the remote being used is within direct line-of-sight of the IR Extender.
CAT5e/6/7 OUT: Connect to a compatible HDBaseT Receiver with a single Cat.5e/6/7 cable for transmission of all data signals.
HDMI IN: Connect to HDMI source equipment such as a media player, game console or set-top box.

Receiver’s Front Panel

ISP: This button is reserved for factory use only.
STD/UPDATE: This switch is reserved for factory use only. The default setting is “STD”.
RS-232 OUT: Connect to a serial controllable device for the extension of RS-232 signals.
SYNC LED: This LED will illuminate when a live input source is detected.
- HQ/STD LED: This LED will illuminate whenever the AVLC function is active. A green LED indicates that AVLC is in HQ (High Quality) mode. A red LED indicates that AVLC is in STD (Standard) mode.
- POWER LED: This LED will illuminate to indicate the unit is on and receiving power.
- LINK LED: This LED will illuminate solidly when a live connection with a compatible Receiver is active. The LED will blink with a regular pattern if a Receiver is connected but there is not currently a live signal. The LED will blink with an irregular pattern if a connection error has occurred.

Receiver’s Rear Panel

IR2 BLASTER: Connect to the provided IR Blaster to transmit IR signals to devices within direct line-of-sight of the IR Blaster.
IR1 EXTENDER: Connect to the provided IR Extender to extend the IR control range of remotely located devices. Ensure that the remote being used is within direct line-of-sight of the IR Extender.
CAT5e/6/7: Connect to a compatible HDBaseT Transmitter with a single Cat.5e/6/7 cable for transmission of all data signals.
HDMI OUT: Connect to an HDMI TV, monitor or amplifier for digital video and audio output.

IR Pin Assignment

RS-232 Protocol

UNIT

Pin| Pinout
1|
2| TxD
3| RxD
4|
5| GND
6|
7|
8|
9|
TERMINAL

Pin| Pinout
1|
2| RxD
3| TxD
4|
5| GND
6|
7|
8|
9|

CONNECTION DIAGRAM

SPECIFICATIONS

Transmitter’s Technical Specifications

HDMI Bandwidth 600MHz/18Gbps
HDBaseT Bandwidth 340MHz/10.2Gbps
Input Ports 1×HDMI
Output Ports 1×Cat.5e/6/7
Pass-through Ports 1×IR Extender [3.5mm] 1×IR Blaster [3.5mm] 1×RS-232 [9-pin D-sub]
IR Frequency 30 – 50kHz (30 – 60kHz under ideal conditions)
Baud Rate Up to 115200bps
Power Supply 48V/0.83A DC (US/EU standards, CE/FCC/
UL certified)
ESD Protection Human Body Model: ±8kV (Air Discharge) ±4kV (Contact Discharge)
Dimensions 128mm×25mm×108mm (W×H×D) [Case Only] 128mm×25mm×117mm (W×H×D) [All Inclusive]
Weight 385g
Chassis Material Metal
Silkscreen Colour Black
Operating Temperature 0˚C – 40˚C/32˚F – 104˚F
Storage Temperature −20˚C – 60˚C/−4˚F – 140˚F
Relative Humidity 20 – 90% RH (Non-condensing)
Power Consumption 8.47W

Receiver’s Technical Specifications

HDMI Bandwidth 600MHz/18Gbps
HDBaseT Bandwidth 340MHz/10.2Gbps
Input Ports 1×Cat.5e/6/7
Output Ports 1×HDMI
Pass-through Ports 1×IR Extender [3.5mm] 1×IR Blaster [3.5mm] 1×RS-232 [9-pin D-sub]
IR Frequency 30 – 50kHz (30 – 60kHz under ideal conditions)
Baud Rate Up to 115200bps
Power Supply PoH
ESD Protection Human Body Model: ±8kV (Air Discharge) ±4kV (Contact Discharge)
Dimensions 128mm×25mm×108mm (W×H×D) [Case Only] 128mm×25mm×117mm (W×H×D) [All Inclusive]
Weight 386g
Chassis Material Metal
Silkscreen Colour Black
Operating Temperature 0˚C – 40˚C/32˚F – 104˚F
Storage Temperature −20˚C – 60˚C/−4˚F – 140˚F
Relative Humidity 20 – 90% RH (Non-condensing)
Power Consumption 9.8W

Video Specifications

HDMI HDMI

Supported PC Resolutions (Hz) Input Output

640×480| 60, 72, 75, 85| P| P
720×400| 70, 85| P| P
800×600| 56, 60, 72, 75, 85| P| P
1024×768| 60, 70, 75, 85| P| P
1152×864| 75| P| P
1280×720| 50, 60| P| P
1280×768| 60, 75, 85| P| P
1280×800| 60, 60 (RB)| P| P
1280×960| 60| P| P
1280×1024| 60| P| P
1360×768| 60| P| P
1366×768| 60| P| P
1400×1050| 60, 60 (RB)| P| P
1440×900| 60, 60 (RB)| P| P
1600×900| 60| P| P
1600×1200| 60| P| P
1680×1050| 60, 60 (RB)| P| P
1920×1080| 60| P| P
1920×1200| 60| P| P
HDMI HDMI

Supported TV Resolutions (Hz) Input Output

720×480i| 59.94, 60| P| P
720×576i| 50| P| P
720×480p| 59.94, 60| P| P
720×576p| 50| P| P
1280×720p| 50, 59.94, 60| P| P
1920×1080i| 50, 59.94, 60| P| P
1920×1080p| 50, 59.94, 60| P| P
1920×1080p| 23.97, 24, 25, 29.97, 30| P| P
3840×2160p| 24, 25, 30| P| P
4096×2160p| 24, 25, 30| P| P
3840×2160p (YUV 4:2:0)| 50, 60| P| P
3840×2160p| 50, 60| P| P