Poemoon P41-600G1 Modern 9 Light Pendant Light Instruction Manual
- May 15, 2024
- Poemoon
Table of Contents
Poemoon P41-600G1 Modern 9 Light Pendant Light
Product Information
Specifications:
- Product Name: Modern 9-light Pendant Light
- Manufacturer Contact: E-mail: banleris@163.com
- Parts Included: Mounting Bracket, Canopy, Wire nut, Hex Nut, Mounting Screws, Decorative Fastener, Pendant Chain, Lamp Body, Tube, Iron Frame, Large Patch, Small Glass, Large Glass, Crystal Prisms, Hollow Rods, Screws
Frequently Asked Questions
- Q: What should I do if I am missing any mounting accessories?
- A: If you are missing any accessories, please contact us via email at banleris@163.com for assistance.
WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR REMOVE THIS FIXTURE.
PARTS
NOTE: Please carefully check all the mounting accessories are complete before installation, if you are missing any accessories, please feel free to contact us through email.
TOOLS REQUIRED
Electrical test reminder
- Test the electricity of the light fixture first before installing, and if it can be properly functioning please follow the steps 1-6 as below to install.
- Any questions about the installation process, please contact the email address at the bottom of the first page, prompt response will be offered within 24 hours.
INSTALLATION STEPS
Step 1: ( Install the mounting bracket )
- Turn off the light power supply at the circuit breaker box and the wall switch.
- Fix the mounting bracket to the ceiling. There are two types of screws included in the accessories bag. Use them in different types of ceilings.
- For outlet box that is ACCEPTABLE FOR LIGHT SUPPORT:
- Unscrew out the hollow screw(b2) and hex nut(b3) from the pendant chain(B).
- Thread hollow screw through the hole position of mounting bracket(a1) and fix it with hex nut(b3).
- Pull out all wires from the outlet box, then match the holes on the mounting bracket with the outlet box.
- Use mounting screw(a2) to fix the mounting bracket.
- Cover the canopy(A), install the metal ring(b4) to the hollow screw(b2).
- If there is still an obvious gap between the canopy and the ceiling after the decorative fastener(b1) is installed, you can adjust the hollow screw to make sure there is no gap between the canopy and the ceiling.
Step 2: (Installation of tubes)
As the picture 2a show :
- Take out the screws(d1) and the screws(d2) on the tubes(D).
- Put the tube align the large screw holes,then drill the screws(d1) into the iron frame(E) throuht the screw holes to fixed it.
- Repeat the above action and secure the remaining three as well.
Step 3: (Installation of lamp body)
As the picture 3a show:
- Put the tubes(D) align the screw holes,then drill the screws(d2) into the lamp body(C) throuht the screw holes to fixed it.
- Repeat the above action and secure the remaining three as well.
Step 4: (Organizing the wires and adjusting the chain length )
- Before the installation, please adjust the length of the pendant chain first. Use a plier to remove pendant chain(B) to shorten the chain.
- All wires need to pass through the pendant chain(B), not all chain rings are necessary.
- Use the pendant chain to connect the lamp body(C) by rotating the O-Ring(b5) to metal ring(c1),
Step 5: (Connecting wires )
- Loosen the decorative fastener(b1) from the metal ring(b4) , remove the canopy(A) .
- All wires need to pass throuh the metal ring(b4) and canopy(A) .
- Connect the indoor live wire with the black wire(L) of the light fixture by twisting two wires together, then use the wire nut(a3) to twist them together.
- Connect the indoor netural wire with the white wire(N) of the light fixture by twisting two wires together, then use the wire nut(a3) to twist them together.
- Connect the indoor ground wire with the ground wire of the light fixture by twisting two wires together, then use the wire nut(a3) to twist them together.
- Use the wire tape to tie all the wires for a secure connection, then put all the connected wires into the outlet box.
- Put the canopy (A) onto the outlet box and let mounting bracket go through the holes on the canopy, then use metal ring and decorative fastener to tighten them up.
Step 6: (Installation of glass and crystal prisms )
- Suggested to install the glass in order bilateral symmetry, and then install it from bottom to top.
- Before installation, remove the film from the Large Patch and Small Patch.
- Install large glass(G) first.the large patch(f1) pass through the large glass(G) , small patch(f2), then pass through the reserved holes on the lamp body and tighten them with hex nut.
- Next install small glass(F).the large patch(f1) pass through the small glass(F),small patch(f2), and hollow rod(f 3), tighten them together. then pass through the reserved holes on the lamp body and tighten them with hollow rod screws(f 4).
- Connecting crystal prisms(H) and lamo body(C) with butterfly buckle(h1).
- Connecting crystal prisms(H) and iron frame(E) with butterfly buckle(h1).
- Install E12 bulb.turn on the power supply.turn on the light switch.
Troubleshooting
WARNING
Make sure the power is off at the electrical panel box before you attempt any repairs.If any problems or dissatisfaction during using, please contact us: E-mail: banleris@163.com.
| Problem | Solution |
|---|
The light does not work.
| Make sure the power supply is on.
Test or replace the switch.
Check the wiring.
Replace the light bulb.
The fuse blows or the circuit breaker trips when the light is turned on.|
Check the wire connection.
Care and Cleaning
Disconnect power to the fixture by turning off the circuit breaker or by
removing the fuse at the fuse box.
Use a dry or slightly dampened clean cloth to wipe the interior surface of the
fixture.
If you have any problems or dissatisfaction, Please feel free to contact E-mail: banleris@163.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>