CYP PUV-2606RX HDMI Receiver with USB Connectivity Instruction Manual

CYP PUV-2606RX HDMI Receiver with USB Connectivity

INSTRUCTION MANUAL

Model: PUV-2606RX

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment:

• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.
• Please completely disconnect the power when the unit is not in use to avoid wasting electricity.

VERSION HISTORY

1. INTRODUCTION

This HDBaseT 2.0 Receiver is a great solution for receiving uncompressed HD audio and video as well as Ethernet and control via a single run of Cat.5e/6/7 cable over distances of up to 100 meters. Multiple data and control signal types are supported, including USB 2.0, IR, RS-232 and LAN connections. An independent balanced analogue stereo audio output is also provided to support easy audio signal extension from compatible Transmitters. The HDBaseT input supports receiving resolutions up to a maximum of 4K@30Hz (4:4:4, 8-bit) or 4K@60Hz (4:2:0, 8-bit) from a compatible HDBaseT Transmitter.
When paired with this unit’s standard Transmitter, 2 switchable USB 2.0 host (Type B) connections are available (1 on the Transmitter, 1 on the Receiver) which can connect to devices on up to 6 USB 2.0 (Type A) ports (3 on the

Transmitter, 3 on the Receiver) forming a highly flexible KVM extension configuration (Note: Only 1 USB host may be active at a time).

This Receiver (PSE) can provide PoH (Power over HDBaseT) power to the connected HDBaseT Transmitter (PD) (compatible Transmitters only), allowing for greater flexibility within different installation scenarios. This unit is controllable via a front panel button.

2. APPLICATIONS

• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control

3. PACKAGE CONTENTS

• 1× HDBaseT to HDMI/USB Receiver
• 1× 24V/2.7A DC Power Adapter
• 1× 3.5mm to IR Blaster Cable
• 1× 3.5mm to IR Extender cable
• 1× Shockproof Feet (Set of 4)
• 1× Operation Manual

4. SYSTEM REQUIREMENTS

• HDMI receiving equipment such as an HDTV, monitor or audio amplifier.
• A compatible HDBaseT 2.0 Transmitter with PoH (PD) support is recommended.
• The use of Premium High Speed HDMI cables, and industry standard Cat.6, Cat.6a or Cat.7, is highly recommended.

5. FEATURES

• HDMI 2.0 and DVI 1.0 compatible
• HDCP 2.2 and HDCP 1.x compliant
• HDBaseT 2.0 compatible
• 1 HDBaseT input and 1 HDMI output
• 3 USB 2.0 Type A ports and 1 USB 2.0 Type B port
• Supports HDBaseT input resolutions up to 4K@60Hz (4:2:0, 8-bit)
• HDMI output supports resolutions up to 4K@60Hz (4:2:0, 8-bit)
• HDBaseT input receives video, audio, and data over a single Cat.5e/6/7
• cable and can reach distances up to 100m/230ft at 4K when using Cat.6a/7
• HDBaseT feature support: HD Video and Audio, 100BaseT Ethernet, PoH (PSE), and control (bi-directional IR/RS-232/USB 2.0)
• Supports CEC bypass
• Supports pass-through of audio formats including LPCM (up to 8 channels), Bitstream and HD Bitstream from HDMI sources
• Reception of independent analogue stereo audio extension
• Flexible USB host selection using the front panel button
• Note: Multiple USB hosts may be connected at once (up to 2 total, between the Tx and a compatible Rx unit) with a single selected host active at a time
• Supports local power, or power via PoH from Receiver (PSE) to
• Transmitter (PD) (compatible Receivers only)
• Controllable via a front panel button

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

1. POWER LED: This LED will illuminate to indicate the unit is on and receiving power.
2. LINK LED: This LED will illuminate solidly when a live connection with a compatible Transmitter is active.
3. USB 2.0 (Type A) Ports: Connect directly to standard USB 2.0 peripherals such as a mouse, keyboard or flash drive to extend their USB functionality to the designated Host Port.
4. USB SELECT Button & LED: Press this button to toggle between the USB Host Ports on the Receiver or compatible Transmitter. The LED will illuminate to indicate which USB Host Port is currently active. If the LED is off, the USB Host Port on the connected Transmitter is active.

Note: Changing the USB host will force the HDBaseT connection to briefly disconnect while it reconfigures. The connected host (PC, laptop, etc.) may also take a moment to detect all available devices.

USB 2.0 (Type B) Port: Connect directly to a standard USB host such as a PC or laptop to extend its USB functionality to all currently connected USB devices.

Note: Multiple USB hosts may be connected at once (up to 2 total, between the Tx and a compatible Rx unit) with a single selected host active at a time

6.2 Rear Panel

1. DC 24V Port: Plug the 24V DC power adapter into this port and connect it to an AC wall outlet for power.
2. SERVICE Switch: This switch is reserved for factory use only. The default setting is “OFF”.
3. BYPASS RS-232 Terminal Block: Connect to a PC, laptop, or serial controllable device with a 3-pin adapter cable for the extension of RS-232 signals between both ends of the HDBaseT connection.
4. IR OUT Port: Connect to the provided IR Blaster to transmit IR signals from the other end of the HDBaseT connection to devices within direct line-of-sight of the IR Blaster.

IR IN Port: Connect to the provided IR Extender to receive IR control signals and extend them to devices connected to the other end of the HDBaseT connection. Ensure that the remote being used is within direct line-of-sight of the IR Extender.

5. CAT 5e/6/7 IN Port: Connect to a compatible HDBaseT Transmitter with a single Cat.5e/6/7 cable for reception of all data signals. PoH will also be supplied to a connected compatible PD Transmitter.
6. HDMI OUT: Connect to HDMI TVs, monitors or amplifiers for digital video and audio output.
7. Analogue OUT Terminal Block: Connect to powered speakers or an amplifier for balanced analogue stereo audio output. This will output the independent audio channel sent by compatible HDBaseT Transmitters.
8. LAN Port: Connect to an Ethernet supporting device or to your local network, as appropriate, to extend the network to both ends of the HDBaseT connection.

6.3 IR Cable Pinouts

6.4 RS-232 Pinout and Defaults

7. CONNECTION DIAGRAM

8. SPECIFICATIONS

8.1 Technical Specifications

1×Stereo Audio (5-pin Terminal Block)
Pass-through Ports| 1×IR Extender (3.5mm)
1×IR Blaster (3.5mm)
3×USB 2.0 (Type A)
1×USB 2.0 (Type B)
1×RS-232 (3-pin Terminal Block)
1×LAN (RJ-45)
IR Frequency| 30 – 50kHz
(30 – 60kHz under ideal conditions)
Baud Rate| Up to 115200
Power Supply| 24V/2.7A DC
(US/EU standards, CE/FCC/UL certified)
ESD Protection (HBM)| ±8kV (Air Discharge)
±4kV (Contact Discharge)
Dimensions (W×H×D)| 231.5mm×25mm×108mm [Case Only] 231.5mm×25mm×110mm [All Inclusive]
Weight| 647g
Chassis Material| Metal (Steel)
Chassis Colour| Black
Operating Temperature| 0˚C – 40˚C/32˚F – 104˚F
Storage Temperature|  -20˚C – 60˚C/-4˚F – 140˚F
Relative Humidity| 20 – 90% RH (Non-condensing)
Power Consumption| 40.44W

8.2 Video Specifications

8.3 Audio Specifications

8.3.1 Digital Audio

HDMI Input/Output

LPCM
Max Channels| 8 Channels
Sampling Rate (kHz)| 32, 44.1, 48, 88.2, 96, 176.4, 192
Bitstream
Supported Formats| Standard & High-Definition

8.3.2 Analogue Audio

Analogue Output

Max Audio Level| 1Vrms
THD+N| < −80dB@0dBFS 1kHz (A-wt)
SNR| > 80dB@0dBFS
Frequency Response| < ±1dB@20Hz~20kHz
Crosstalk| < −80dB@10kHz
Impedance| 470Ω
Type| Balanced

8.4 Cable Specifications

8-bit
High Speed HDMI Cable
HDMI Output| 15m| 10m| 5m| O
Ethernet Cable
Cat.5e/6| 100m| 90m| O
Cat.6a/7| 100m| 100m| O

Bandwidth Category Examples:

• 1080p (FHD Video)
  – Up to 1080p@60Hz, 12-bit colour
  – Data rates lower than 5.3Gbps or below 225MHz TMDS clock

• 4K30 (UHD Video)
  – 4K@24/25/30Hz & 4K@50/60Hz (4:2:0), 8-bit colour
  – Data rates higher than 5.3Gbps or above 225MHz TMDS clock but below 10.2Gbps

• 4K60 (UHD+ Video)
  – 4K@50/60Hz (4:4:4, 8-bit)
  – 4K@50/60Hz (4:2:0, 10-bit HDR)
  – Data rates higher than 10.2Gbps

8.5 HDBaseT Features

9. ACRONYMS

Specifications

• Model: PUV-2606RX
• Type: HDBaseTTM to HDMI Receiver with USB Connectivity
• Version: 1.1

CYP (UK) Ltd.,

Unit 7, Shepperton Business Park, Govett Avenue,
Shepperton, Middlesex, TW17 8BA
Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279
Email: sales@cypeurope.com
www.cypeurope.com
RDV1

Frequently Asked Questions (FAQ)

Q: Can I connect multiple USB devices simultaneously?

A: Only one USB host can be active at a time, allowing connection to devices on up to 6 USB 2.0 ports.

Q: How do I control the unit?

A: The unit is controllable via a front panel button.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>