HOLMAN CD1120C Retractable Hose Reel User Guide
- June 3, 2024
- Holman
Table of Contents
HOLMAN CD1120C Retractable Hose Reel
Introduction
Your HOLMAN Retractable Hose Reel uses a 12mm reinforced hose for added
strength and durability, rated to 1000kPa, and includes a MULTI-FUNCTION SPRAY
GUN.
For your information, please read these installation instructions before using
your Retractable Hose Reel. Please keep all instructions and refer to them
when necessary. Do not leave the tap on–turn the tap off after use and release
excess pressure before retracting back into the housing
Overview
- Mounting Tube
- Hexagonal Coach Bolts
- Wall Plugs
- 180° Wall Bracket
- Garden Hose
- Tap-to-Reel Hose
- Multi-Function Spray Gun
- Housing
- Hose Connectors
- Universal Tap Adaptor
- Stopper
- Inspection opening
Installation
Your Retractable Hose Reel should be installed nearest to your chosen water source for convenience of use.
- Check the TAP-TO-REEL HOSE can reach your tap prior to installing the WALL BRACKET
- Take the WALL BRACKET and place it against either a wall or a wooden post
- Mark inside the center of each of the bracket holes to prepare for drilling If you are attaching your Hose Reel to a wooden post, you will not require the WALL PLUGS as the COACH BOLTS can screw directly into wood.
- Use the table below to select the correct drill bit for your Hose Reel If using plugs that were not included with your Hose Reel, drill slightly undersize as masonry materials all have different properties which will ensure the wall plugs have a secure fit. It is very important to use the correct size drill bit, so a very secure fit of the wall bracket is made before installing the Retractable Hose Reel.
- When ready, drill all four holes, then hammer the WALL PLUGS gently into your wall (if attaching to a wall)
- hammer the WALL PLUGS gently into your wall (if attaching to a wall)
- Screw in each HEXAGONAL COACH BOLT until all four have a secure hold on the bracket against the surface
- Insert the MOUNTING TUBE back into the holes on the WALL BRACKET and HOUSING. Then replace the securing pin in the base of the MOUNTING TUBE
- Hose Reel and slot it over the WALL BRACKET. Align the holes in the HOUSING with the holes in the WALL BRACKET
- Connect your TAP-TO-REEL HOSE to your garden tap
- Take your Retractable Hose Reel, and remove the securing pin at the base of the MOUNTING TUB
Care and Troubleshooting
You will find an indication sticker meter before the maximum length.
Do not pull the hose past this point. When walking the GARDEN HOSE back to the
HOUSING, turn off the tap, and press the lever on the watering gun to release
the water pressure in the hose. This makes the retraction of the GARDEN HOSE a
lot easier and prolongs the life of your Hose Reel.If the GARDEN HOSE
retraction wheel is stuck and the GARDEN HOSE is fully extended, the wheel
still has moved past this point. Grip the GARDEN HOSE close to the guide hole
and gently pull.
The retraction wheel will give you enough movement to unlock itself before you
slowly allow the auto retraction wheel to wind the GARDEN HOSE back into the
unit.
WARNINGS
- Do not leave the water turned on with the hose under pressure when not in use.
- Always turn the water off and draw the water from the hose after use.
- Do not attempt to pull the hose reel apart.
- Do not pull the GARDEN HOSE to start retraction and let go of the hose. Always guide the GARDEN HOSE back to the housing.
Spare Parts
Plastic 180º Wall Bracket
-
Includes 4 x Wall Plugs and 4 x Hexagonal Coach Bolts.
-
Mounting Tube
Includes securing pin. -
Tap to Reel Hose
(1110TTR, 11120TTR, 1130TTR)
-
Retractable Hose Reel Lid
-
Ball Stopper
(1110BS, 1120BS, 1130BS)
All spare parts are available for 10m, 20m and 30m Retractable Hose Reels.
Do not dismantle the Hose Reel for additional spare parts. Other internal
metal parts can cause injury if tampered with. These parts are not available
for replacement.
To order spare parts please call our customer service team on
1300 716 188, or order online:
www.holmanindustries.com.au
Warranty
2-Year Replacement Guarantee – Housing Holman offers a 2-year replacement
guarantee with this product.HOUSING In Australia our goods come with
guarantees
that cannot be excluded under the Australian Consumer Law. You are entitled to
a replacement or refund for a major failure and compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. As well as your statutory rights
referred to above and any other rights and remedies you have under any other
laws relating to your Holman product, we also provide you with a Holman
guarantee.
Holman guarantees this product against defects caused by faulty workmanship
and materials for 2 years of domestic use from the date of purchase. During
this guarantee period
Holman will replace any defective product. Packaging and instructions may not
be replaced unless faulty. In the event of a product being replaced during the
guarantee period, the guarantee on the replacement product will expire 2 years
from the purchase date of the original product, not 2 years from the date of
replacement. To the extent permitted by law, this Holman Replacement Guarantee
excludes liability for consequential loss or any other loss or damage caused
to the property of persons arising from any cause whatsoever. It also excludes
defects caused by the product not being used in accordance with instructions,
accidental damage, misuse, or being tampered with by unauthorized persons,
excludes normal wear and tear, and does not cover the cost of claiming under
the warranty or transporting the goods to and from the place of purchase.
Should you suspect your product may be defective and need some clarification
or advice please contact us directly: 1300 716 188
support@holmanindustries.com.au 11 Walters
Drive, Osborne Park 6017 WAIf you are certain your product is defective and is
covered by the terms of this warranty, you will need to present your defective
product and your purchase receipt as proof of purchase to the place you
purchased it from, where the retailer will replace the product for you on our
behalf.
We really appreciate having you as a customer and would like to say thank you for choosing us. We recommend registering your new product on our website. This will ensure we have a copy of your purchase and activate an extended warranty. Keep up to date to with relevant product information and special offers available through our newsletter.ww.holmanindustries.com.au/product- registration/ Thanks again for choosing Holman
References
- Holman Industries - Irrigation, Garden Lights, Plumbing
- Product Registration and Extended Warranty - Holman Industries