baolifeng 2AXK8-V8 Bluetooth Headphone User Manual
- September 28, 2024
- BAOLIFENG
Table of Contents
2AXK8-V8 Bluetooth Headphone
Product Information
Specifications
FCC WARNING: This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may
cause undesired operation.
Note: The Grantee is not responsible for any changes or
modifications not expressly approved by the party responsible for
compliance. Such modifications could void the user’s authority to
operate the equipment.
The device has been evaluated to meet general RF exposure
requirement.
This equipment complies with FCC’s RF radiation exposure limits
set forth for an uncontrolled environment. This device and its
antenna(s) must not be co-located or conjunction with any other
antenna or transmitter.
Product Usage Instructions
1. Installation
Take the headphone from the package and adjust the angle to meet
ear comfort.
2. Using the Headphone
(a) Pairing
-
Power on the headphone, the LED indicator will flash between
red and blue alternately, and the headphone will report “Power
on”. -
Activate your mobile phone’s Bluetooth function and search for
available Bluetooth devices. -
Select V8 from the list, once connected, it will show in your
phone. The headphone will report connected.
(b) Connected the Second Phone
-
After the first cellphone pairing successfully, please turn off
the headphone then turn it on, also disconnect the first
phone. -
Pair for the second cellphone as per the above steps. After
successful pairing, with voice report “Phone connected”, please
connect the first phone. Now, the two phones are connected at the
same time.
(c) Answer/End the Call
-
When a call comes in, short press the TALKING button to receive
the call. -
Voice answer/end the call: Say YES to answer the call, say NO
to reject it.
3. Charging
The product has a built-in rechargeable battery that can be
charged using a micro USB cable. For the first use, charge the
headphone fully.
-
While charging, the Red LED Indicator will light up. After
charging is finished, the Red LED Indicator will turn off. -
If the headphone is low on power, it will sound an alarm every
5 minutes until it powers off. Please charge it promptly.
4. Care and Maintenance
-
Do not expose the headphone to liquid, moisture, or
humidity. -
Avoid using abrasive cleaning solvents to clean the
headphone. -
Avoid placing the headphone in high temperatures to prevent
explosion risks. -
Avoid contact with sharp objects to prevent scratching and
damage. -
Do not attempt to disassemble the headphone as it does not
contain serviceable components. -
If not in use for a long time, store the headphone in a dry
place away from extreme temperatures, humidity, and dust.
FAQ
Q: How do I reset my Bluetooth headphone?
A: To reset your Bluetooth headphone, turn it off and back on
again. Then follow the pairing instructions as mentioned in the
user manual.
User Manual 1.About Bluetooth headphone.
Thank you for purchasing the Bluetooth headphone,for the sake of making full
of the functions of the products, please read the user manual carefully in
advance.
2.Appearance and function.
3.Installation.
Take the headphone from the package and adjust the angle to meet ear comfort.
4.Using the headphone.
(1).Pairing.
For the first time to use the headphone,it need pair manually as the follow
steps.
a.Power on the headphone,the LED indicator will flash between red and blue
alternately,the headphone will report”Power on”
b.Activate your mobile phone’s Bluetooth function and search for available
Bluetooth
devices.
c.Select “V8” from the list,once it connected will show in your phone.The
headphone will
report “connected” (2).Connected the second phone. a.After the first cellphone
pairing successfully, please turn off the headphone then turn on it,also
disconnect the first phone. b.Please pairing for the second cellphone as the
above steps, after the second cellphone pairing successfully and with voice
report “Phone connected”,please connected the first phone,now the two phone
connected at the same time. (3)Answer/End the Call.
a.Once the call coming, the headphone will ring when the call is coming, short
press the
“TALKING” button to receive call.
b.Voice answer/end the call.
This headphone had integrated the newest smart technology to allow the voice
answer
the call,once the call coming,just say “YES” will answer the call,say “NO”
will reject the
call.
c.Recall the last number. Short press “TALKING” button twice for the last
number redialing. d.Voice dialing. Ensure your mobile phone can support the
voice dialing function and you had set it before you use this function. In
standby mode, short press the “TALKING” button to activate. At this time, the
voice dialing function in mobile phone will be automatically activated, please
speak out the name of your expected toward the microphone. (Please refer to
mobile phone’s user manual). Caution: only apply to the mobile phone with
function configuration of voice dialing. (4).Play/Pause. In the normal
state,press the “PLAY” button to play the music,press again stop the music.
Press the volume button for long time to adjust the volume,press the volume
button for the last/next song.
5.Charging.
The product with built-in rechargeable battery can be charged random by the
micro USB. To use your Bluetooth headphone for the first time, please charge
the headphone fully. (1)While charging, the Red LED Indicator will light up,
after charging finished, the Red LED Indicator will be off. (2)While lower
power,the headphone will be report “didi” for alarm every 5 minutes until
power off,please charge the headphone intime.
6.Care and maintenance.
(1)Do not expose the speakerphone to liquid, moisture or humidity. (2)Do not
use abrasive cleaning solvents to clean the speakerphone. (3)Do not place the
speakerphone in high temperature, as it may result in an explosion (4)Do not
expose the speakerphone to contract with sharp objects as this will cause
scratching and damage.
(5)Do not attempt to disassemble the speakerphone, as it does not contain
serviceable components. (6)If you do not use the speakerphone for the long
time, be sure to store it in a dry place, free extreme temperature, humidity
and dust.
7.Specification.
Bluetooth Specifications………….. Version4.0, 10meters Operating Frequency
Band………. 2.4GHz to 2.48GHz unlicensed ISM band Rechargeable Battery…3.7VDC,
90mAH, (Li-ion battery) AD/DC Charger………DC5 to 6V, 400mA Normal Charge
Time………………up to 1hrs. (approx) Talking time……………………… up to 6hrs. Standby
Time………………………up to 300hrs. Weight…………………………… 18g (without package) Note: The
above configuration may change or upgrade according to the product development
plan without any prior notice.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: –Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver. –Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. –Consult the dealer or an experienced radio/TV
technician for help.
Note: The Grantee is not responsible for any changes or modifications not
expressly approved by the party responsible for compliance. such modifications
could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement.
This equipment complies with FCC’s RF radiation exposure limits set forth for
an uncontrolled environment. This device and its antenna(s) must not be co-
located or conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>