Dongguan Baolifeng Electronic Technology Co Ltd 2AXK8-SP16 SP16 Bluetooth Headset User Manual
- June 1, 2024
- Dongguan Baolifeng Electronic Technology Co Ltd
Table of Contents
Dongguan Baolifeng Electronic Technology Co Ltd 2AXK8-SP16 SP16 Bluetooth Headset
Read the manual before use
If you have any questions, please contact the customer service to deal with them immediately Please do not make negative comments at will. Our service is up to your satisfaction
Important: Plug in the charging wire for charging at the first time after receiving the goods, and use it after fully charging, which can make the Bluetooth headset last longer
Important: Do not use super fast charging with current above 2A to avoid damaging the circuit chip due to excessive current
Important: Plug in the charging wire for charging at the first time after receiving the goods, and use it after fully charging, which can make the Bluetooth headset last longer
Important: Do not use super fast charging with current above 2A to avoid damaging the circuit chip due to excessive current
-
the first step , to make sure that the Bluetooth of the phone is off, take out two earphones, wait 10 seconds, earphones light changes from fast flashing to synchronous slow flashing, which means that the earphone has been paired. (taws mode)
-
Turn on Bluetooth on your mobile phone, search for SP16 devices and click on the connection.
-
Successfully connected to mobile phone, two lights turned into blue light and slowly flashed
the earphone touch control Is marked In red circle
If there is a delay in the game, you can quickly touch you right ear and switch to game mode to reduce the delay
If only one side has sound, please first delete the SP16 that has been connected, turn off the Bluetooth of your phone, the earphones need to be paired once, enter the taws mode, and return to the first step
Important: Plug in the charging wire tor charging at the l1rst time after
receiving the goods, and use it after fully charging. which can make the
Bluetooth headset last longer
Important: Do not use super fast charging with current above 2A to avoid
damaging the circuit chip due to excessive current
The connection steps are as follows
Open the cover, the first step to make sure that the Bluetooth of the phone is off, take out two earphones from charge box, wait 10 seconds, the earphone light changes from fast flashing to synchronous slow flashing, which means that the earphone has been paired. (tows mode) earphones makes a sound “pairing” Turn on the Bluetooth of your phone, search for “SP16”, click Connect
Touch Function
- Click on the earphone touch area: play/pause
- Double- click the earphone touch area: pull-back
- Triple- tap headphone touch area: volume down/ volume up
- Quadruple tap left earphone touch area: summon Siri function
- Four click right earphone touch area Game/ music mode switching
- Long press 2 seconds earphone touch area: previous/next song
the earphone touch control is marked in red circle
Charging Method
Plug in the cable we sent, and be careful to plug it in to the end. The number of the display flashes to recharge the earphone charging compartment. When you charge the display “100”, it is full. (with power display)
If you find that you do not like or will not use the goods. remember to contact the store customer service to teach you how to use them. If you do not like to return the goods and remember to choose another reason for returning, this is very important to us. Thank you very much !
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause armful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party re-Possible for compliance. such modifications could void the users authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement.
This 1equipment complies with FCC’s RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co- located or conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>