SEALEY 9009 Filter Housing Instruction Manual
- September 27, 2024
- SEALEY
Table of Contents
**SEALEY 9009 Filter Housing Instruction Manual
**
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
REFER TO INSTRUCTIONS
IMPORTANT : PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
INTRODUCTION
Used to retain Sealey 9006 P2 R D particulate prefilter. Used in conjunction with Sealey 9001 and 9002 filter cartridges. Used in conjunction with filter cartridges gives greater adaptability. Supplied as a pair in a resealable storage bag.
Type Examination Ref.: 0082/1694/079/03/22/0186
Notified Body: Apave Sudeurope sas (notified body number 0082)
SAFETY
IMPORTANT: The use limitations of these respirators depend on the type of
filter they are used with as well as the conditions of the environment user
work in, contaminant concentration, type of work, etc. For an effective and
proper use of the filters, read carefully the following instructions and keep
this document for further consultation.
These filters DO NOT supply oxygen (O2).
Use in adequately ventilated areas. DO NOT use in case of oxygen deficiency.
DO NOT use in explosive atmospheres.
Filters should NOT be used in fire-fighting or too work with open flames or
molten metal since the combustion of the activated carbon
contained in the filters can generate high levels of toxic substances.
The right filter must be chosen according to concentration and type of
contaminant in each case.
DO NOT use as protection against carbon monoxide under any circumstances.
DO NOT modify or repair the filter or cover. In case of damage or loss of
seal, replace the product with a new one.
Filters, combined filters and absorbers require no maintenance or repair.
Leave work if respiratory protection is damaged, if you have difficulty
breathing and / or if you start to feel nauseous or dizzy.
DO NOT use respirators with filters or combined filters or absorbers in
closed silos, wells, canals or other closed places without ventilation.
DO NOT use in an oxygen enriched atmosphere.
DO NOT use in an atmosphere with unknown air quality.
Use cleansers also as indicated in the respirator manual
DO NOT use if the storage took place under conditions other than those
specified by the manufacturer. This may affect the shelf life.
DO NOT remove the adapter once installed during use.
Ensure the type of filter is the correct one for intended use, and that you
have installed both filters of the same type.
Inspect the filters and respirator for any signs of damage before each use. If
damaged or the item has expired it must be replaced.
Only use filters that have been stored correctly in their original packaging
as per these instructions.
The use of filters must comply with current legislation, regulations about
respiratory protection and regulations from various official bodies.
ASSEMBLY
BEFORE EACH USE
- Read instruction for use carefully.
- Make sure the type of filter is the correct one for intended use.
- Make sure that you installed both filters of the same type.
- Make sure that the filter as well as the respirator do not present any signs of tearing, distortions, dents, nor dirt Should this be the case, it must be disposed of.
- Make sure filter is in its original packaging.
- Filter must be inspected before its use. In case of contamination, distortion and/or expiration it must be replaced.
FITTING THE FILTERS
Match the plastic filter connection with the filter holder on the mask. Press
and turn the filter all the way clockwise. Repeat with second filter.
PRE-FILTER
An additional pre-filter can be fitted if required. (Not supplied)
Assembly of 9006 (pre-filter) and 9009 (cover). Place the 9006 pre-filter onto
the 9001 filter with the printed side facing in. Place the 9009 cover on the
filter and press together. Verify that the pre-filter covers the 9001 filter.
Reverse the procedure to disassemble the product.
OBSOLESCENCE
Filters, combined filters, absorbers and cover have the production date on the packaging and on the product. The use-by date is 5 years from the production date, which is valid when stored in the original packaging in accordance with the manufacturer’s recommendations.
FILTER DISPOSAL
Once filters have been used, they must be disposed of according to the current national legislation.
This document has been drawn up according to Regulation (EU) 2016/425 as amended to apply to GB for Personal Protective Equipment. The declaration of conformity can be accessed at www.sealey.co.uk.
|
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
|
---|---|---
Note : It is our policy to continually improve products and as such we
reserve the right to alter data,specifications and component parts without
prior notice.
Important : No Liability is accepted for incorrect use of this product.
Warranty : Guarantee is 12 months from purchase date, proof of which is
required for any claim.
EU | Sealey EU Ltd, Farney Street, Carrickmacross, Co. Monaghan, A81 PK68
Ireland
UK | Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds,
Suffolk. IP32 7AR
01284 757500 sales@sealey.co.ukwww.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>