BAFANG DP C10 28 Inch 36V LCD User Manual
- October 30, 2023
- BAFANG
Table of Contents
7 USER MANUAL FOR
DP C10.CAN
USER MANUAL FOR DISPLAY
IMPORTANT NOTICE
- If the error information from the display cannot be corrected according to the instructions, please contact your retailer.
- The product is designed to be waterproof. It is highly recommended to avoid submerging the display under water.
- Do not clean the display with a steam jet, high-pressure cleaner or water hose.
- Please use this product with care.
- Do not use thinners or other solvents to clean the display. Such substances can damage the surfaces.
- Warranty is not included due to wear and normal use and aging.
INTRODUCTION OF DISPLAY
- Model: DP C10.CAN BUS
- The housing material is PC and Acrylic, and the button material is made of silicone.
- The label marking is as follows:
Note: Please keep the QR code label attached to the display cable. The information from the Label is used for a later possible software update.
PRODUCT DESCRIPTION
7.3.1 Specifications
- Operating temperature: -20℃~45 ℃
- Storage temperature: -20℃~50 ℃
- Waterproof: IP65
- Bearing humidity: 30%-70% RH
7.3.2 Functional Overview
-
Speed display (including speed in real time (SPEED), top speed (MAXS) and average speed (AVG), switching between km and miles)
-
Switching between km and miles
-
Battery capacity indicator
-
Automatic sensors explanation of the lighting system
-
Brightness setting for backlight
-
Indication of performance support
-
Walk assistance
-
Kilometer stand (including single-trip distance, total distance)
-
Display for the remaining distance.(Depends on your riding style)
-
Motor output power indicator
-
Energy consumption indicator CALORIES
(Note: If the display has this function) -
Error messages view
-
Service
-
USB charge function
DISPLAY
- Display of battery capacity in real time.
- Menu.
- Service: please see the service section.
- Digital speed display.
- Speed mode , top speed (MAXS) – Average speed (AVG).
- Kilometer stand, Daily kilometers (TRIP) – Total kilometers (TOTAL).
- Data: Display data, which corresponds to the current mode.
- Walking assistance .
- USB charging indicator displays the icon , if an external USB device is connected to thedisplay.
- The display shows this symbol, if thelight is on.
- Error indicator .
- Error code indicator .
- Speed unit.
- Unit indicator.
- Remaining distance (RANGE).
- Support level
KEY DEFINITION
NORMAL OPERATION
7.6.1 Switching the System ON/OFF
Press and hold (>2S) on the display to turn on the system. Press and hold
(>2S) again to turn off the system.
If the “automatic shutdown time” is set to 5 minutes (it can be set with the
“Auto Off” function, See “Auto Off”), the display will automatically be turned
off within the desired time when it is not in operation.
7.6.2 Selection of Support Levels
When the display is turned on, press (<0.5S) the or button to switch to the support level, the lowest level is 1, the highest level is 5. When the system is switched on, the support level starts in level 1. There is no support at level null.
7.6.3 Selection mode
Briefly press (<0.5s) the button to see the different trip modes. Trip: daily
kilometers (TRIP) – to- tal kilometers (TOTAL) – Maximum speed (MAXS) –
Average speed (AVG) – Remaining distance (RANGE) – Output power (W) – Energy
consumption (C (only with torque sensor fitted)).
7.6.4 Headlights / backlighting
Hold (>2S) the button to activate the headlight and backlight.
Hold (>2S) the button again to turn off the headlight and backlight. The
brightness of the backlight can be set in the display settings “Brightness”.
(If the display /Pedelec is switched on in a dark environment, the display
backlight/headlight will automatically be switched on. If the display
backlight/headlight has been manually switched off, the automatic sensor
function is deactivated.
You can only turn on the light manually after switching on the system again.)
7.6.5 Walk Assistance
The Walk assistance can only be activated with a standing pedelec.
Activation: Briefly press (<0.5S) the button until to level null, and then
press (<0.5s) the button, the symbol is displayed. Now hold down the button
and the Walk assistance will activate. The symbol will flashes and the pedelec
moves approx. 6 km/h. After releasing the button, the motor stops
automatically and switches back to level null (if no any option be activated
in 5 second). If no speed signal is detected, it shows 2.5km/h.
7.6.6 Battery capacity indication
The battery capacity is showed in ten bars. Each full bar represents a
remaining capacity of the battery in a percentage, if the frame of indicator
blinks that means to charge. (as shown in the figure below):
| Bars | Charge in Percentage |
|---|---|
| 10 | ≥90% |
| 9 | 80%≤C<90% |
| 8 | 70%≤C<80% |
| 7 | 60%≤C<70% |
| 6 | 50%≤C<60% |
| 5 | 40%≤C<50% |
| 4 | 30%≤C<40% |
| 3 | 20%≤C<30% |
| 2 | 10%≤C<20% |
| 1 | 5%≤C<10% |
| Blinking | C<5% |
7.6.7 USB charge function
If an external USB device is connected to the display, the icon appears, the
device will be charged. The maximum charging voltage is 5V and the maximum
charging current is 500mA.
SETTINGS
After the display is turned on, quickly press (<0.3S) the button twice to access the “MENU” interface. pressing the or button, you can select and reset the options. Then press (<0.3S) the button twice to confirm your selected option and to return to the main screen. If no button is pressed within 10 seconds in “MENU” interface, the display will automatically return to the main screen and no data will be saved.
7.7.1 Setting
7.7.1.1 Reset mileage
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface and “tC” appears on the display (as shown below). Now using
the or button, choose between “y”(YES) or “n”(NO). If choose “y”, the Daily
kilometers (TRIP), Maximum speed (MAX) and Average speed (AVG) will be reset.
Once you have chosen your desired selection, press (<0.3S) the button twice
tosave and return to the main screen, or you can press (<0.3S) the button
once to save and enter next item “Selection of unit in km/Miles”.
NOTE: If the daily kilometers accumulate 99999km, the daily kilometers
will be reset automatically.
7.7.1.2 Selection of unit in km/Miles
When the system is on, quickly press (<0.3S) the button twice to access the “MENU” interface, repetitively press the button until the “S7” appears on the display (as shown below). Now using the or button, choose between “km/h” or “mile/h”. Once you have chosen your desired selection, press (<0.3S) the button twice to save and return to the main screen, or you can press (<0.3S) the button once to save and enter next item “Set light sensitivity”.
7.7.1.3 Set light sensitivity
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “bL0” appears on the
display (as shown below). And then press to increase or to reduce (light
sensitivity for 0-5). Chose 0 means turn off the light sensitivity. Once you
have chosen your desired selection, press (<0.3S) the button twice to save and
return to the main screen, or you can press (<0.3S) the button once to save
and enter next item “Set display brightness”.
7.7.1.4 Set display brightness
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “bL1” appears on the
display (as shown below). And then press to increase or to reduce (brightness
for 1-5). Once you have chosen your desired selection, press (<0.3S) the
button twice to save and return to the main screen, or you can press (<0.3S)
the button once to save and enter next item “Set Auto Off”.
7.7.1.5 Set Auto Off
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “OFF” appears on the
display (as shown below). And then press to increase or to reduce (brightness
for 1-9minute). Once you have chosen your desired selection, press (<0.3S) the
button twice to save and return to the main screen, or you can press (<0.3S)
the button once to save and enter next item “Service Tip”.
7.7.1.6 Service Tip
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “nnA” appears on the
display (as shown below). And then press or to choose between “0” or “1”.
Chose 0 means turn off the notification. Once you have chosen your desired
selection, press (<0.3S) the button twice to save and return to the main
screen.
NOTE: If the “Service” function switch on, every 5000 km (the mileage of more than 5000 km) the indicator is dis- played every time at switch on.
7.7.2 View Information
All data in this item cannot be changed, only to be viewed.
7.7.2.1 Wheel Size
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “LUd” appears on the
display (as shown below).
Once you have viewed your desired information, press (<0.3S) the button twice
to save and return to the main screen, or you can press (<0.3S) the button
once to enter next item “Speed Limit”.
7.7.2.2 Speed Limit
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “SPL” appears on the
display (as shown below).
Once you have viewed your desired information, press (<0.3S) the button twice
to save and return to the main screen, or you can press (<0.3S) the button
once to enter next item “Controller hardware info”.
7.7.2.3 Controller hardware info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “CHc (Controller
Hardware check)” appears on the display (as shown below).
Once you have viewed your desired information, press (<0.3S) the button twice
to save and return to the main screen, or you can press (<0.3S) the button
once to enter next item “Controller software info”.
7.7.2.4 Controller software info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “CSc (Controller
Software check)” appears on the display (as shown below).
Once you have viewed your desired information, press (<0.3S) the button twice
to save and return to the main screen, or you can press (<0.3S) the button
once to enter next item “Display hardware info”.
7.7.2.5 Display hardware info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “dHc (Display
Hardware check)” appears on the display (as shown below).
Once you have viewed your desired informa- tion, press (<0.3S) the button
twice to save and return to the main screen, or you can press (<0.3S) the
button once to enter next item “Display software info”.
7.7.2.6 Display software info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “dSc (Display
Software check)” appears on the display (as shown below). Once you have viewed
your desired information, press (<0.3S) the button twice to save and return
to the main screen, or you can press (<0.3S) the button once to enter next
item “BMS hardware info”.
7.7.2.7 BMS hardware info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “bHc (BMS Hardware
check)” appears on the display (as shown below).
Once you have viewed your desired information, press (<0.3S) the button twice
to save and return to the main screen, or you can press (<0.3S) the button
once to enter next item “BMS software info”.
7.7.2.8 BMS software info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “dSc (Display
Software check)” appears on the display (as shown below).
Once you have viewed your desired information, press (<0.3S) the button twice
to save and return to the main screen, or you can press (<0.3S) the button
once to enter next item “Sensor hardware info”.
7.7.2.9 Sensor hardware info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “SHc (Sensor
Hardware check)” appears on the display (as shown below).
Once you have viewed your desired information, press (<0.3S) the button twice
to save and return to the main screen, or you can press (<0.3S) the button
once to enter next item “Sensor software info”.
NOTE: This information is not displayed, if there are no torque sensor in
the drive system.
7.7.2.10 Sensor software info
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “SSc (Sensor
Software check)” appears on the display (as shown below).
Once you have viewed your desired informa-tion, press (<0.3S) the button twice
to save and return to the main screen, or you can press (<0.3S) the button
once to enter next item “Battery info”.
NOTE: This information is not displayed, if there are no torque sensor in the drive system.
7.7.2.11 Battery Information
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “b01” appears on the
display (as shown below). You can briefly press (0.3s) to view all information
of the battery.
Once you have viewed your desired information, press (<0.3S) the button twice
to save and return to the main screen, or you can press (<0.3S) the button
once to enter next item “Message of Error Code”.
| Content | Explanation |
|---|---|
| b01 | Current temperature (°C) |
| b04 | Voltage (V) |
| b06 | Discharge (A) |
| b07 | Remaining Capacity (A/h) |
| b08 | Total Capacity (A/h) |
| b09 | Relative SOC (%) |
| b10 | Absolute SOC (%) |
| b11 | Charging cycles (number) |
| b12 | Maximum not charging time (Hr) |
| b13 | Recently not charging time (Hr) |
| d00 | Number of battery cell |
| d01 | Voltage of cell 1 (m/V) |
| d02 | Voltage of cell 2 (m/V) |
| dn | Voltage of cell n (m/V) |
NOTE: If no data is detected, “–” is displayed.
7.7.2.12 Message of Error Code
When the system is on, quickly press (<0.3S) the button twice to access the
“MENU” interface, repetitively press the button until the “E00” appears on the
display (as shown below). You can briefly press (0.3s) to view last ten Error
Code “EO0” to “EO9”. Error code “00” means that there is no error.
Once you have viewed your desired information, press (<0.3S) the button twice
to save and return to the main screen.
ERROR CODE DEFINITION
The display can show the errors of a pedelec. If an error is detected, the
wrench icon appears on the display and one of the following error codes will
be displayed.
Note: Please read the description of the error code carefully. If you see
the error code, restart the system first. If the problem is not resolved,
please contact your dealer.
| Error | Declaration | Troubleshooting |
|---|---|---|
| 4 | The throttle has fault. | 1. Check the connector of throttle whether they |
are correctly connected.
2. Disconnect the throttle, If the problem still occurs, please contact your
retailer. (only with this function)
5| The throttle is not back in its correct position.| Check the throttle can
adjust back into its correct position, if the situation does not improve,
please change to a new throttle.(only with this function)
7| Overvoltage protection| 1. Remove the battery.
2. Re-Insert the battery.
3. If the problem persists, please contact your retailer.
8| Error with the hall sensor signal inside the motor| Please contact your
retailer.
9| Error with the Engine phase’s| Please contact your retailer.
10| The temperature inside the engine has reached its maximum protection
value| 1. Turn off the system and allow the Pedelec to cool down.
2. If the problem persists, please contact your retailer.
11| The temperature sensor inside the motor has an error| Please contact your
retailer.
12| Error with the current sensor in the controller| Please contact your
retailer.
13| Error with the temperature sensor inside of the battery| Please contact
your retailer.
14| The protection temperature inside the controller has reached its maximum
protection value| 1. Turn off the system and let the pedelec cool down.
2. If the problem persists, please contact your retailer.
15| Error with the temperature sensor inside the controller| Please contact
your retailer.
21| Speed sensor Error| 1. Restart the system
2. Check that the magnet attached to the spoke is aligned with the speed
sensor and
that the distance is between 10 mm and 20 mm.
3. Check that the speed sensor connector is connected correctly.
4. If the error persists, please contact your retailer.
25| Torque signal Error| 1. Check that all connections are connected
correctly.
2. If the error persists, please contact your retailer.
26| Speed signal of the torque sensor has an error| 1.Check the connector from
the speed sensor to make sure it is connected correctly.
2.Check the speed sensor for signs of damage.
3.If the problem persists, please contact your retailer.
27| Overcurrent from controller| Please contact your retailer.
30| Communication problem| 1. Check all connections are correctly connected.
2. If the error persists, please contact your retailer.
33| Brake signal has an error (If brake sensors are fitted)| 1. Check all
connectors.
2. If the error continues to occur, please contact your retailer.
35| Detection circuit for 15V has an error| Please contact your retailer.
36| Detection circuit on the keypad has an error| Please contact your
retailer.
37| WDT circuit is faulty| Please contact your retailer.
41| Total voltage from the battery is too high| Please contact your retailer.
42| Total voltage from the battery is too low| Please contact your retailer.
43| Total power from the battery cells is too high| Please contact your
retailer.
44| Voltage of the single cell is too high| Please contact your retailer.
45| Temperature from the battery is too high| Please contact your retailer.
46| The temperature of the battery is too low| Please contact your retailer.
47| SOC of the battery is too high| Please contact your retailer.
48| SOC of the battery is too low| Please contact your retailer.
61| Switching detection defect| Please contact your retailer. (only with this
function)
62| Electronic derailleur cannot release.| Please contact your retailer. (only
with this function)
71| Electronic lock is jammed| Please contact your retailer. (only with this
function)
81| Bluetooth module has an error| Please contact your retailer. (only with
this function)
BF-UM-C-DP C10-EN November 2019
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>