TEKVOX 78042-7A Touchscreen Controller with Wall Mounting Bracket Installation Guide

: September 27, 2024
: TEKVOX

Table of Contents

78042-7A Touchscreen Controller with Wall Mounting Bracket
Product Information
Specifications:
Product Usage Instructions:

78042-7A Touchscreen Controller with Wall Mounting Bracket

Product Information

Specifications:

Product Name: TCX7 – Podium
Model Number: 78042-7A
Components included in the Product Package:
- 6 Wood Screws (4)
- TCX7 Touchscreen Controller
- Mounting Wedge
- Device Plate
- Security Bracket
- 6-32 Machine Screws (4)

Product Usage Instructions:

Step 1: Select Location for TCX7

Choose a location that is easily accessible and not obstructed
by other equipment. Ensure there is at least 3 inches of space on
either side of the mounting wedge. Do not mount directly over
structural furniture members.

Step 2: Drill Hole for Cable Pass-Through

If drilling is permitted, drill a hole for cable pass-through.
If not, proceed with over-table cable routing.

Step 3: Attach Mounting Wedge to Surface

Route the cable through the mounting wedge. Attach the mounting
wedge using the provided wood screws. Do not overtighten the
screws.

Step 4: Attach the Device Plate to the Mounting Wedge

Secure the device plate to the front of the mounting wedge using
the provided screws. Ensure it is level and centered before
tightening.

Step 5: Route Cable up Through Mounting Wedge

If using a cable pass-through hole, route the cable through and
out of the mounting wedge.

Step 6: Connect & Mount TCX7

Connect the Category cable to the TCX7 port labeled POE. Ensure
the other end is connected to a PoE-capable network. Mount TCX7 by
aligning slots with tabs on the device plate and pushing it into
place.

Step 7: Attach Security Bracket

Attach the security bracket on top of the mounting wedge using
the provided screws. Ensure it fits snugly without obstructing the
screen.

FAQ

Q: How do I remove the TCX7 Touchscreen Controller?

A: To remove the controller, simply reverse steps 5-7 of the
installation guide.

TCX7 – Podium
78042-7A Installation Guide
Included in this Product Package:

6 Wood Screws (4)

TCX7 Touchscreen Controller

Mounting Wedge

Device Plate

Security Bracket

6-32 Machine Screws (4)

Step 1: Select Location for TCX7
TCX7 mounting location should be conveniently & easily accessible. TCX7 should not be directly in front of or behind any other equipment.
Allow at least 3″ on either side of mounting wedge. Do not mount TCX7 directly over any structural members of the furniture.

Step 2: Drill Hole for Cable Pass-Through
If drilling additional holes in furniture is prohibited: Skip this step and proceed with installation, following directions for over-table cable routing.
In desired TCX7 location, lightly sketch a 3 ¾” square for locating the mounting wedge. In the center of this square, drill a ¾” dia. cable passthrough hole.
Step 3: Attach Mounting Wedge to Surface
If using over-table cable routing: Route cable through cutout on back of mounting wedge. Run cable out through rectangular opening in mounting wedge, with at least 6″ of slack.

DO NOT OVERTIGHTEN SCREWS

Using the four (4) included #6 wood screws, attach the mounting wedge to the table in its intended location. Ensure that screws are snug, but do not overtighten, as this can cause the threads to tear through the surface and lose holding power.

www.tekvox.com

TCX7 – Podium
78042-7A Installation Guide
Step 4: Attach the Device Plate to the Mounting Wedge
Using two (2) of the provided black 6-32 screws, attach the TCX7 device plate to the front of the mounting wedge. Use the lower set of holes on the front face of the mounting wedge. Tighten screws until snug, but do not overtighten, as this can cause warping of the device plate. Ensure that device plate is level and centered before tightening screws fully.
Step 5: Route Cable up Through Mounting Wedge
6″ If using cable passthrough hole (Step 2): Route cable from underneath table surface through hole drilled in Step 2. Run cable out through rectangular opening in mounting wedge, with at least 6″ of slack.
Step 6: Connect & Mount TCX7
Connect provided Category cable to the TCX7 port labelled “POE.” If cable is connected to second port, device will not power on. Before mounting, ensure that other end of the cable is connected to a PoE-capable network. Wait for the TCX7 to power on, and confirm that it has a network connection.
Gently push TCX7 towards mounting wedge, ensuring that the cable does not get pinched, kinked, or bent too sharply. Align four (4) slots on back of TCX7 with the mounting tabs on the device plate. Once, aligned, push TCX7 towards mounting plate to seat tabs, then press down to lock into place. Check that all tabs are properly seated into their mounting slots.
Step 7: Attach Security Bracket
Using two (2) remaining black 6-32 screws, attach the TCX7 security bracket to the top of the mounting wedge. Security bracket should fit snugly over the top of the TCX7, but should not obscure any portion of the screen. Tighten screws fully.
The TCX7 Touchscreen Controller is now fully installed. To remove for any reason, simply reverse steps 5-7.
www.tekvox.com