IMOU A22EP-V2 A1 2MP WiFi Pan and Tilt Camera User Guide
- June 6, 2024
- imou
Table of Contents
Quick Start Guide
A1
Welcome
Thank you for choosing IMOU.
We are devoted to providing you easy smart home products. If you have problems
using the product, please contact our service team before returning your
product.
Our service mail:
service.global@imoulife.com
Detailed installation instructions & videos, frequently asked questions can be
found at: imoulife.com/support/help Or
scan this QR code to help page.
http://www.imoulife.com/web/support/help
Package content
Camera introduction
Note: Press and hold the reset button for 10 s to reset the camera.
The pattern of the LED indicator is included in the following table.
| LED Status | Device Status |
|---|---|
| Off | ♦ Powered off/LED turned off |
♦ Rebooting after reset
Red light on| ♦ Booting
♦ Device malfunction
Green light flashing| ♦ Waiting for network
Green light on| ♦ Operating properly
Red light flashing| ♦ Network connection failed
Green and red light flashing alternately| ♦ Firmware updating
Tips
To ensure the best possible wireless performance, please make sure
there are no obstacles and electromagnetic interference between the camera and
router.
Troubleshooting
Problem
|
Solution
---|---
Cannot set up camera| ♦ Ensure your mobile device and the camera are within
range of your Wi-Fi router.
♦Ensure the LED indicator on the camera isflashing green before beginning
setup.
The APP says “Failed to configure device network”| ♦Reset your Camera and
connect it again.
♦Some cameras only support 2.4GHz, while some routers have dual band, 2.4G/5G.
Make sure you are connecting 2.4GHz only.
The app says ” Failed to bind”| The camera is already connected to Wi-Fi, but
the router is:
♦ Not connected to Internet
♦ Poor network status
♦ The Wi-Fi signal is not stable due to obstacles or electronic interference
No picture / signal| ♦ Ensure the LED indicator on the camera is flashing
steady green. See ‘LED Status’ section for details if otherwise.
♦ Ensure the camera is properly connected to power using the included USB
power adapter.
♦ Try repositioning the camera, router, or both to improve signal strength.
Picture is not clear| ♦ Check the camera lens for dirt, dust, spider webs.
Clean the lens with a soft, clean cloth.
♦Remove the vinyl cover on the camera lens.
No audio| ♦ Ensure audio function on camera is turned on.
♦ Ensure audio is turned up on viewing device.
Human detection not working| ♦ Ensure you have enabled “Human Detection” in
the Device Settings screen of the lmou LifeApp.
Camera stuck downwards| ♦ Turn off Camera Shielding in Device Settings on the
lmou Life app.
Phone is not reading QR code| ♦ Clean the camera lens of your Smartphone
♦ Ensure that there is enough light on the QR code
♦ Don’t hold the QR code too close to the camera
This product complies with the applicable CE marking directives and standards:
- Low Voltage (LVD) Directive 2014/35/EU.
- Electromagnetic Compatibility (EMC) Directive 2014/30/EU.
- Restrictions of Hazardous Substances (RoHS) Directive 2011/65/EU and its amending Directive (EU) 2015/863.
A copy of the original declaration of conformity may be obtained from
Dahua Technology. The most up to date copy of the signed EU
Declaration of Conformity (DoC) can be found www.imoulife.com/declaration-of- conformity
CE-Electromagnetic Compatibility (EMC)
This digital equipment is compliant with Class B according to EN 55032.
CE-Safety
This product complies with IEC/EN/UL 60950-1 or IEC/EN/UL 62368-1, Safety of
Information Technology Equipment.
Declaration of Conformity CE (Only for the product has RF function)
Hereby, Dahua Technology declares that the radio equipment is compliant with
Radio Equipment Directive (RED) 2014/53/EU. The full text of the EU
declaration of conformity is available at www.imoulife.com/declaration-of-
conformity.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>