PowerA PCGPSTWL Battle Dragon Wireless Controller User Manual

: September 29, 2024
: PowerA

Table of Contents

References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PowerA PCGPSTWL Battle Dragon Wireless Controller User Manual

http://www.powera.com/support

TWO-YEAR LIMITED WARRANTY
For warranty details or support with your authentic PowerA accessories, please visit www.powera.com/support.

USER MANUAL

CONTENTS

Controller
USB adaptor
5 ft. / 1.5 m USB-C® to USB-A Cable
Two analog caps
User Manual

CHARGING CONTROLLER
For best results, fully charge controller prior to first use.

Using a USB-C Cable connect to the USB-C port at the top of the controller, and connect the other end to any powered USB source.
When charging, the battery indicator LED will flash AMBER.
When fully charged the battery indicator LED will be solid GREEN.
Battery Indicator will flash RED when battery is low.

WIRELESS MODE: 2.4G

Insert wireless USB dongle into open PC USB port.
Select “RF” on the mode switch on back of controller.
If controller is off, press the Home button (icon) to turn on (LED will illuminate WHITE).
Press and hold the SYNC button (icon) on top of the controller for 3 seconds to enter pairing mode (LED will flash WHITE rapidly).
Enter the Settings menu on your device and choose the PC Wireless controller. The LED will turn solid WHITE when connected.

WIRELESS MODE: BLUETOOTH

1. Select “BT” on the mode switch on back of controller.
If controller is off, press the Home button (icon) to turn on (LED will illuminate BLUE)
Press and hold the SYNC button (icon) on top of the controller for 3 seconds to enter pairing mode (LED will flash BLUE rapidly).
Enter the Bluetooth settings on your device.
Select the PC Wireless Controller.

WIRED MODE USB

Select “USB” on the mode switch on back of controller.
Using the included USB-C Cable, connect to the USB-C port at the top of the controller, and connect the other end to an available USB port on the PC.
If controller is off, press the Home button (icon) to turn on (LED will illuminate GREEN).

NOTE : A previously paired device will automatically pair to the controller when powered on.

MODE XINPUT TO DIRECT INPUT (2.4 RF / USB WIRED MODE ONLY)

Press and hold the SELECT and START buttons simultaneously for 3 seconds
LED indicator will flash 3 times to indicate MODE has been changed.
To change modes again, press and hold SELECT and START buttons again for 3 seconds until LED flashes 3 times.

TRIGGER LOCK ADJUSTMENT

ANALOG CAPS (OPTIONAL ACCESSORY)
Enhance the controller’s grip and comfort by attaching the analog caps to the analog sticks for improved gameplay.

POWERING OFF
Hold the Home button (icon) for 5 seconds to turn controller off and save battery capacity.

BATTERY STATUS INDICATION
LOW BATTERY = RED LED
BATTERY CHARGING = AMBER LED
BATTERY CHARGED = GREEN LED

ASSIGNING THE ADVANCED GAMING BUTTONS

NOTE: Advanced Gaming Button assignments will remain in memory even after disconnected.

RESETTING THE ADVANCED GAMING BUTTONS

Hold the Program Button down for 2 seconds.
The LED Connection Indicator will slowly flash, signaling the controller is in assign mode.
Press the previously assigned button for 5 seconds, and the function will be cleared.

TURBO SETTING

TROUBLESHOOTING

PROBLEM : My controller will not power on.

SOLUTION : Confirm the controller is fully charged. Plug in to recharge as needed.

PROBLEM : I don’t see my PC controller listed in my device’s settings.

SOLUTION : Press and hold the Bluetooth sync button on top of controller for 3 seconds to enter pairing mode (LED will flash rapidly).

PROBLEM : My wireless controller is not pairing.

SOLUTION : Confirm the battery is charged by plugging in USB-C cable.

SOLUTION : Confirm you are following the Wireless pairing process.

SOLUTION : Insert paper clip into Factory Reset Hole as marked above to reset controller to factory settings.
For latest FAQs, visit www.powera.com/support

TWO-YEAR LIMITED WARRANTY
For warranty details or support with your authentic PowerA accessories, please visit www.powera.com/support.

MOTION WARNING
Playing video games may cause muscle, joint, skin, or eye discomfort. Follow these instructions to avoid problems such as tendinitis, carpal tunnel syndrome, skin irritation or eyestrain:

Avoid excessive play. Take a 10- to 15-minute break every hour, even if you don’t think you need it. Parents should monitor their children for appropriate play.
If your hands, wrists, arms, or eyes become tired or sore while playing, or if you feel symptoms such as tingling, numbness, burning, or stiffness, stop and rest for several hours before playing again.
If you continue to have any of the above symptoms or other discomfort during or after play, stop playing and see a doctor.

MANUFACTURED FOR
ACCO Brands USA LLC
4 Corporate Drive, Lake Zurich, IL 60047
ACCOBRANDS.COM | POWERA.COM | MADE IN CHINA

ADDITIONAL LEGAL
© 2024 ACCO Brands. All Rights Reserved. PowerA and PowerA Logo are trademarks of ACCO Brands.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by ACCO Brands is under license.
Other trademarks and trade names are those of their respective owners.

USB-C® is a registered trademark of USB Implementers Forum.