Lemokey G2 Wireless Mouse User Manual
- September 24, 2024
- Lemokey
Table of Contents
Lemokey G2 Wireless Mouse
User manual
- Right button
- Forward button
- Receiver compartment
- DPI button
- Left button
- Mouse indicator
- Charging port
- Middle wheel button
- 2.4GHz Type – receiver
- Backward button
- Modes toggle
- Wired Mode:
Modes of connection
- When the mode switch is in “OFF” position, the mouse won’t respond if the cable is not connected.
- Connect the cable to the TYPE-C port of the mouse and the USB port on the device. The mouse is ready to use while the indicator lights up.
- When connected by cable, the mode will default to wired mode even if the toggle is in Bluetooth mode or2.4GHz mode.
4GHz Mode
- Switch to “G” mode (2.4GHz mode), and the mouse will automatically turn on 2.4GHz paring. The mouse indicator will slowly flash green.
- Find the 2.4GHz receiver and connect it to the device’s USB. Once successfully connected, the mouse indicator will turn green and stay on for3 seconds before dimming off. The mouse is now ready for use.
- In 2.4GHz paring mode, the mouse indicator will slowly blinkgreen for3 minutes. If the mouse is not connected within 3 minutes, the indicator will turn off. If you need to reconnect, hold both the “Left button+ Middle Wheel+ Right button” for4seconds to re-enter pairing mode.
- If you need to repair the connection in 2.4GHz mode, please unplug the2.4GHz receiver first. Then, hold both the “Left button Middle Wheel+ Right button” for4 seconds, wait for the green light indicator to start flashing, and plug the 2.4GHz receiver back in to complete the pairing process.
- Note: It is recommended that when pairing the G2 in 2.4GHz mode, the mouse should be within 20cm of the receiver.
Bluetooth mode
- Switch to “B” Mode (Bluetooth), and the mouse will automatically turn on Bluetooth pairing mode. The mouse indicator will slowly flash blue.
- Open the Bluetooth settings, search for a device named “Lemokey G2”, then click “connect” to complete paring.
- When in Bluetooth pairing mode, the mouse indicator will slowly blink in blue for 3 minutes. If it’s not connected within 3 minutes, the mouse indicator will turn off. If you need to reconnect, you need to hold the “Left button+MiddleWheel+Rightbutton” for4 seconds to re-enter pairing mode. The indicator will slowly blink blue.
- If the G2 is in Bluetooth mode and needs to pair with a new device, hold both the “Left button+Middle Wheel+Right button” for4 seconds and wait for the blue light to flash on. At this point, Bluetooth has re-entered pairing mode, and you can connect the new device to the G2.
Status indicator
DPI indicator
Report Rate
*Please adjust the report rate in the driver software.
Driver Software
The Lemokey G2 mouse driver can be selected on launcher.lemokey.com. If the driver software can’t connect to the mouse, please contact us for technical support.
Auto-Sleep mode
Auto-Sleep mode will not be activated when in wired mode. When in Bluetooth mode or 2.4GHz mode, the mouse will go to Auto-Sleep mode after 10 minutes of sitting idle to save the battery. Move or click the mouse to wake it up.
How to factory reset
Hold down both the “DPI” button and “Middle Wheel” button for 4 seconds, and
all the LED lights on the mouse will blink. It will blink three times to
indicate that the factory reset is successful.
simultaneously hold for 4 seconds (starts factory reset)
Charging indicator explanation
- The mouse is compatible with all USB ports. For the best signal and charging speed, connecting to the USB3.0 port is recommended when charging or in use.
- If the mouse is connected by the USB Type – C cable when charging but not paired with any devices:
- The mouse indicator will stay RED when charging.
- The mouse indicator will stay GREEN when fully charged.
Note: The product supports up to 5V charging voltage and 150 mA charging current. We are not responsible for any problems caused by improper recharging.
What’s in the box
- Mouse x 1
- Type -C cable x 1
- Extension adapter x 1
- Type -A receiver x 1
- User manual x 1
- Type-A to Type -C adapter x 1
Mouse specification
- Size: 11862.638.2mm
- Weight: 52 ± 3g
- Report Rate(polling rate): 125(White) 500(Green) lO00(Blue) -2000(Yellow) -4000(Red) -B000(Purple)
- Sensor: PixArt 3950
- Resolution: 100-30000DPI
- Battery capacity: 300mAh
- Usage duration: 60 Hours (Under lO00Hz) 35 Hours (1000-4000Hz) 20 Hours (4000-B000Hz)
- Recharge time: 2.5 Hours
- Charging port: Type -C
- Mouse micro switches: Huano Micro Switch (80 million clicks life time) 2.4GHz/ Bluetooth connection range: Approx 10m of open space
- Connection mode: 2.4GHz -Bluetooth -Wired
- Device name: Lemokey G2
Find us at: https://www.lemokey.com
Support@lemokey.com If @lemokey
© @emokey.keyboard X
@ lmokey_com Designed by Lemokey Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>