strands SIBERIA XP SR LED Bar Owner’s Manual

September 24, 2024
Strands

SIBERIA XP SR LED Bar

“`html

Product Information

Specifications

  • Model: SIBERA XP SR/SRC LED BAR

  • Length: 304.7mm-1273.7mm

  • Part Numbers: 809412, 809413, 809414, 809415, 809416, 809417,
    809418, 809419

  • Fuse: 25A

  • Cable Length: 2.5m

  • Operating Voltage: 12-24V

Product Usage Instructions

Hello Function:

This function is activated by flashing the high beams twice
within 2 seconds. Ensure a position light wire is connected to use
this mode.

Switching Modes:

  • To switch to E-mode: Turn off the high beam for 5 seconds, let
    the high beam run for 2 seconds, then flash the high beam 3 times
    within 5 seconds.

  • To switch to Xperience mode: Turn on the high beam for 2
    seconds, then flash the high beam 3 times within 5 seconds.

Signal Connection:

It can be connected with an AUX switch, CANBUS solution with
signal wire, by connecting the signal wire with the original cable
with the car’s main high beam, or using a wireless controller with
a 12-24V system.

Installation:

Ensure not to cut any connectors on the product. Secure loose
cables properly. Do not cut cables shorter than 50 cm to maintain
warranty validity. Tighten screws and bolts securely without
damaging the product.

Maintenance:

Keep the product clean to prolong its lifetime. Use water and
cloth for cleaning. Do not use sharp materials. Follow degreasing
instructions carefully.

FAQ

Q: How can I activate the Hello Function?

A: Flash the high beams twice within 2 seconds with a connected
position light wire.

Q: Can I connect the LED bar with an AUX switch?

A: Yes, it can be connected with an AUX switch, CANBUS solution,
or a wireless controller with a 12-24V system.

Q: What should I do if the cable is shorter than 50 cm?

A: Do not cut the cable shorter than 50 cm to maintain warranty
validity.

“`

MANUAL SIBERA XP SR/SRC LED BAR
RED: + High beam BLACK: (-) Negative GREY: Signal wire connect to +(VDC) WHITE: +White position light YELLOW: +Yellow position light
Hello Function:This function is activated by flashing the high beams twice within 2 seconds. To use this mode, ensure a position light wire is connected.
When you start the LED bar for the first time, it is set to Xperience mode. -To switch back to E-mode, turn off the high beam for 5 seconds, let the high beam run for 2 seconds, then flash the high beam 3times within 5 seconds. -To switch to Xperience mode, turn on the high beam for 2 seconds, then flash the high beam 3 times within 5 seconds.

(Can be connect with aux switch, canbus solution or wirelss controller)
Alternative for signal connection : It can be connected with an AUX switch, CANBUS solution with signal wire, By connecting signal wire with original cable with car main high beam, or a wireless controller with 12-24v system.

(Length for SR/SRC version 304.7mm-1273.7mm)12″-50″

(Part No.809412,809413,809414,809415,809416,809417,809418,809419) *25A fuse for above articles , 2.5m cable, Hello function
Contact us if you need support: support@strands.se or +46(0)320-450450
www.strands.se www.strandseurope.com

1 of 2

(PIN1)RED: + High beam (PIN2)BLACK: (-) Negative (PIN3)WHITE: +White position light (PIN4)YELLOW: +Yellow position light

(It can be connected with an AUX switch, CANBUS solution with signal wire, By connecting signal wire with original cable with car main high beam by using strands cable kit like 270477 or a similar type. a wireless controller with 12-24v system)

(Part no.809411) *No fuse, 15cm cable with DT4 and pig tail, No hello function

Note: The connection diagrams shown are examples only. This guide focuses on connecting an external switch for a single light bar fixture. *Side brackets are not included in the package. If needed, you can get them separately using our part number 270361.
READ THIS BEFORE INSTALLATION READ ALL INSTRUCTIONS AND STUDY DIAGRAMS BEFORE INSTALLING YOUR NEW LIGHTS!
LEGAL MOUNTING
Check with state or local authorities for laws governing usage and proper mounting of your new lights.
TAKE CARE OF YOUR PRODUCT
Keep the product clean. Dirt on the lens and heat-sink may shorten the products lifetime. Top cover of the roof bar can clean with normal water and cloth, Do not use any sharp material to rub on it. Follow the degreasing instructions carefully and rinse off gently with cold or lukewarm water on low pressure.
WARNING! Strong chemicals should not be used on the product. If you accidently get strong chemicals on the product, rinse off immediately, use plenty of water so that no chemicals remain in any joint. Some chemicals have a small amount of solvent in them, this can dissolve sealing adhesives and compromise the product’s waterproofness. Some chemicals pull out liquid from plastic and rubber-based components, which makes the plastic or rubber brittle and bursts more easily. Be careful not to use high water pressure close up on the product. If you use high water pressure at short distances, most products find it difficult to close out the water.
INSTALLATION If there is a contact/connector on the product, it should not be cutted. If the connector is cut, the warranty is not valid.
If the product has loose cable and no connector. If the cable is shorter than 50 cm, the cable must not be cutted. If the cable is cut, the warranty is not valid. If the cable is longer than 50 cm, it is ok to shorten the cable, but not shorter than 50 cm. If the cable is cut shorter than 50 cm, the warranty is not valid.
Tighten screws and bolts so that they do not loosen or chafe. Do not tighten screws so hard that the protective bearings on the product breaks.
WARNING!
Do not use higher voltage than the product description states. This light becomes hot under continuous use. Don´t remove or touch the casing for at least 30 minutes after turning the lamp off.

2 of 2

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals