HUAWEI 21501718 Smart Module Sliding Door User Guide

HUAWEI 21501718 Smart Module Sliding Door User Guide

Installations Instructions

Installing Bottom Sealing Plates and the Inner Door Frame

NOTE
Before installation, ensure that the left and right end cabinets are on the same horizontal line.

Step 1: Assemble front and rear sealing plates that are as wide as the cabinet.
NOTE
Take the side sealing plate for the 1100 mm or 1200 mm deep cabinet out of the door box materials, and splice the bottom sealing plate for the 600 mm or 800 mm wide cabinet based on the site requirements.
Step 2: Secure the front and rear sealing plates to the cabinet.
Step 3: Place the side with dents upwards, and snap the side sealing plate into the front and rear sealing plates.

1. Securing holes for cabinets with castors
2. Securing holes for cabinets without castors

NOTE
Before installation, remove the rear cover of the door head and reinstall it after all components are installed.
Step 1: Secure the internal posts to the internal door head.

NOTE
After removing the maintenance panels from both sides of the posts, put the posts and door head horizontally on the floor and assemble them. After the assembly is complete, verify that the posts are flush with the door head.

Step 2: Secure the posts to the skylight connective plate.
Step 3: Remove the front wheel of the damper.
Step 4: Secure the bottom of the posts to the cabinets.

Installing a Guide Rail

Step 1: Secure the guide rail to the door frame.

NOTE
Before installation, remove the protective rubber strips from the glass door.

Installing Rubber Strips

Step 1: Install the door rubber strips.

NOTE

• Ensure that the door is in close contact with the rubber strips without gaps.
• Ensure that the inner and outer rubber strips are flush with the door and the rubber strip at the bottom is as wide as the door.

Installing a Glass Door and Damper

Step 1: Push the door onto the guide rail.
Step 2: Set the spring of the middle buffer to the compressed state.
Step 3: Push an end buffer into each end of the guide rail according to the direction of the arrow on the label.
Step 4: Secure the screws at both ends of the guide rail.
Step 5: Push the buffers to the ends of the guide rail until they are in close contact with the guide rail screws.
Step 6: Secure the buffers when the springs of the buffers are in the compressed state.

NOTE

• Ensure that there is no gap between the glass doors and they are flush.
• Ensure that there is no friction between the glass doors and posts.
• Ensure that the buffers are installed properly.

Step 1: Reinstall the front wheel of the damper.

(Optional) Installing a Magnetic Lock

Step 1: Secure the magnet fastener and washer to the door panel.
Step 2: Secure the magnets on the left and right sides to the fasteners respectively.
Step 3: Remove the magnetic lock accessory and save the two removed screws for later use.
Step 4: Secure the two magnetic locks to the magnetic lock fasteners using screws.
Step 5: Secure the assembled magnetic locks to the guide rail.

Adjusting the Magnetic Lock Gap

If the magnetic lock fails to attract the magnet after being installed on a sliding door, you can adjust the magnetic lock by either of the following methods:

Method 1:
Loosen the two M6 screws on the fixing corner pieces of the magnet. Then move the fixing corner piece assembly horizontally until the magnet closely attaches to the magnetic lock.

Method 2:
Loosen the two screws that secure the magnetic lock. Then insert a washer between the magnetic lock and the sheet metal fastener until the magnet closely attaches to the magnetic lock.

Installing Door Box Hanging Kits

NOTE
In case of 1100 mm cabinet scenario, the 1100 mm door box separately delivered is used, the 1200 mm door box packaged in the door materials is abandoned.

Step 1: Facing the aisle, secure the door box hanging kits labeled L and R to the top of the cabinet.
Step 2: Pull out the cables that are preinstalled in the post.
Step 3: Secure the door box hanging kits to the post.

Installing an External Door Frame

Step 1: Secure the external posts to the external door head.

Put the posts and door head horizontally on the floor and assemble them.
After the assembly is complete, verify that the posts are flush with the door head.

Installing an External Door Frame and Door Boxes

NOTE
Before installing the door boxes, check whether the eLight needs to be installed. If the eLight needs to be installed, you are advised to install the eLight first and then perform this step.

Step 1: Stand up the door frame, and secure it to the top of the internal door frame of the cabinet.
Step 2: Tighten the screws at the bottom of the posts.
Step 3: Install door boxes.

Installing Side Covers for the Posts

Step 1: Install side covers for the posts.

(Optional) Installing a PAD Mounting Kit and Access Control Device

Step 1: Install the bottom plate of the PAD mounting kit.
Step 2: Pre-route the cables for the PAD and access control device.
Step 3: Remove the baffle plate from the installation position and secure the baffle plate with the cable hole in the lower part.

Step 4: (Optional) If the feet in the lower part of the PAD mounting bracket are not as wide as the PAD, adjust the feet.

Step 6: Install the PAD cover and pull the pre-routed cables out of the cable hole.

Step 7: Adjust the feet on the PAD mounting support and clamp the PAD into the PAD mounting support.

Step 8: Install the access control device.
a: Remove the screws (set aside) from the access control device and take off the baseplate.
b: Secure the baseplate to the baffle plate.
c: Route the cable of the access control device through the cable hole in the baffle plate.
d: Secure the access control device to the baseplate.

Copyright © Huawei Digital Power Technologies Co., Ltd. 2022. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>