CYP PUV-1830-AVLC-KIT HDBaseT1 Full 4K Transmitter Instruction Manual

CYP PUV-1830-AVLC-KIT HDBaseT1 Full 4K Transmitter

Specifications

• Model: PUV-1830-AVLC-KIT
• Technology: HDBaseT1 Full 4K AVLC Series
• Features: OAR, LAN & PoH

Product Usage Instructions

Introduction
The PUV-1830-AVLC-KIT is a high-quality transmitter and receiver kit designed for various audiovisual applications.

Applications

The kit is ideal for

• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control

Package Contents
The package includes the transmitter, receiver, power adapter, IR extender, and necessary cables for setup.

System Requirements
To use the kit, you will need

• HDMI source equipment (media player, video game console, set-top box)

• Industry standard Cat.6, Cat.6a, or Cat.7 cable

• Premium High Speed HDMI cable.

Frequently Asked Questions (FAQ)
Q: Can I use Cat.5e cable instead of Cat.6 or higher?
A: While Cat.6 or higher is recommended for optimal performance, Cat.5e may work depending on the distance and resolution requirements.

DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. CYP (UK) Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be contained in this document. CYP (UK) Ltd also makes no commitment to update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document and/or product at any time and without notice.

COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means—electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from CYP (UK) Ltd.
© Copyright 2024 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1

TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:

• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.

REVISION HISTORY

INTRODUCTION

This HDMI over single Cat.5e/6/7 Transmitter and Receiver Kit is a great solution for extending HD audio and video as well as Ethernet and control via a single run of Cat.5e/6/7 cable over distances of up to 100 metres. Multiple data and control interfaces are provided, including IR, RS-232 and LAN connections. This kit complies with the advanced HDCP 2.2 and HDMI 2.0 standards, as well as supporting the legacy HDCP 1.x and HDMI 1.x standards. Despite HDBaseT’s  10.Gbps bandwidth limitation, 4K UHD HDMI video sources, up to and including 4K@60Hz (4:4:4, 8-bit) as well as 10/12-bit sources with HDR, are able to be processed and extended by the use of AVLC (Adaptive Visually Lossless Compression) when connected to the AVLC Receiver.
Beyond video, data, and control this unit also contains useful audio features. The Optical Audio Return (OAR) feature supports transmitting optical audio back from a compatible Receiver for local playback. Round-ing out the feature set is robust EDID management as well as automatic HDBaseT clock stretching and TMDS re-clocking support. The Transmitter (PSE) can provide 48V PoH (Power over HDBaseT) to the Receiver (PD), al-lowing for greater flexibility within different installation scenarios.

APPLICATIONS

• 48V PoH from Transmitter (PSE) to Receiver (PD)
• Household entertainment sharing and control
• Lecture room display and control
•  Showroom display and control
• Meeting room presentation and control
• Classroom display and control

PACKAGE CONTENTS

•  1×HDMI over HDBaseT Transmitter with HDR & OAR  1×48V/0.83A DC Power Adapter

•  1×Power Cord

• 1×3.5mm to IR Blaster Cable

•  1×3-pin Terminal Block to 9-pin D-sub Adapter Cable

• 1×Rackmount Ears (Set of 2)

• 1×HDMI over HDBaseT Receiver with HDR & OAR

• 1×3.5mm to IR Extender Cable

• 1×Rackmount Ears (Set of 2)

• 1×Operation Manual

SYSTEM REQUIREMENTS

HDMI source equipment such as a media player, video game console or set-top box.
The use of industry standard Cat.6, Cat.6a or Cat.7 cable is highly recommended.
The use of “Premium High Speed HDMI” cables is highly recommended.

FEATURES

• HDMI with HDR, 3D & 4K@60Hz support, DVI 1.0 compatible
• HDCP 2.2 and HDCP 1.x compliant
• Supports up to 4K UHD (18Gbps, 4K@50/60Hz 4:4:4, 8-bit) video input and output
• Supports 10-bit and 12-bit HDR (High Dynamic Range) input/output and Deep Colour input and output up to 12-bit Supports CEC bypass
• Simultaneous transmission of uncompressed video, audio and data over a single Cat.5e/6/7 cable up to 100m/328ft at 1080p60 and 70m/230ft at 4K
• HDBaseT feature support: HD Video and Audio, 100BaseT Ethernet, 48V PoH, and Control (bidirectional IR/RS-232 pass-through)
• Integrated AVLC (Adaptive Visually Lossless Compression) activates when the bandwidth requirements of the source are beyond 10.2Gbps (340MHz) allowing for sources up to 18Gbps (600MHz) to be sent to a compatible Receiver with
• no loss of visual quality
• The AVLC feature allows manual selection between High Quality Mode (Full bandwidth) and Standard Mode (Lower bandwidth, useful for longer cable runs with 4K sources)
• Supports the Optical Audio Return (OAR) function to transmit optical audio from a compatible Receiver to the Transmitter
• Comprehensive EDID management support including 6 pre-defined EDIDs, 9 user EDIDs and an EDID bypass mode
• PC-based EDID management software allows for the uploading of customised user EDIDs via USB
• Supports HDMI DDC bus clock stretching for improved compatibility with certain Blu-ray players
• Performs TMDS re-clocking and signal re-generation for improved signal integrity
• Ultra-thin design (16mm thickness) for convenient installation
• Supports standard 48V PoH from Transmitter (PSE) to Receiver (PD) (compatible Receivers only)

OPERATION CONTROLS AND FUNCTIONS

Front Panel

1. DC 48V: Plug the 48V DC power adapter into this port and connect it to an AC wall outlet for power. Note: Please be sure to follow the polarity labels on the unit and the adapter’s wires.
2. POWER LED: This LED will illuminate to indicate the unit is on and receiving power. LINK LED: This LED will illuminate solidly when a live connection with a compatible Receiver is active.
3. OPT. OUT: Connect to powered speakers or an amplifier for digital audio output using an appropriate optical cable. Audio is sourced from the Optical Audio Return input on a connected compatible Receiver.
4. IR EXTENDER 1: Connect to an IR Extender to extend the IR control range of devices connected to the other end of the HDBaseT connection. Ensure that the remote being used is within direct line-of- sight of the IR Extender.
5. IR BLASTER 2: Connect to the provided IR Blaster to transmit IR signals from the other end of the HDBaseT connection to devices within direct line-of-sight of the IR Blaster.
6. SERVICE: This USB port is reserved for firmware update and user EDID upload use.
7. RS-232: Connect to a PC, laptop or other serial control device with a 3-pin adapter cable for the extension of RS-232 signals to the Receiver in “Bypass” mode, or for control this unit when in “Console” mode. Note: Depending on the controlled device connected to the Receiver side, the Tx and Rx pins might need to be reversed.
8. CONSOLE/BYPASS: This switch controls the operational mode of the RS-232 port. When set to “Bypass”, RS-232 signals will be passed to the connected Receiver. When set to “Console” the RS-232 port may be used to send commands directly to the Transmitter.

Note: RS-232 bypass requires both the Transmitter and Receiver to be set to “Bypass” mode.

Rear Panel

1. U LAN: Connect to an Ethernet supporting device or to your local network, as appropriate, to extend the network to both ends of the HDBaseT connection.
2. HDMI IN: Connect to HDMI source equipment such as a media player, game console or set-top box.
3. HQ & STD LED: These LEDs illuminate to indicate which AVLC mode will be used when AVLC is required. The lower green LED indicates that AVLC will use HQ (High Quality) mode. The upper yellow LED indicates that AVLC will use STD (Standard) mode.
4. HQ/STD SWITCH: This switch allows the user to select which compression mode to use when AVLC is active, High Quality or Standard. Note: HQ (High Quality) mode uses the least amount of compression and provides the highest possible visual quality (perceptually identical to the original). STD (Standard Quality) mode applies additional signal reduction methods to lower the bandwidth requirements of 4K sources further, improving transmission reliability over longer cable runs at the cost of some visual fidelity.
5. CAT5/6/7 OUT: Connect to a compatible HDBaseT Receiver with a single Cat.5e/6/7 cable for transmission of all data signals. 48V PoH will also be supplied when connected to a compatible PD Receiver. Note: The 48V PoH function is designed for powering compatible Receiver units only. Non-PoH Receivers will need their own power supply. Receivers from other brands may not be compatible.

Right Panel

1. EDID: The EDID dipswitch block provides a way to select the EDID to use with the connected source. By using a combination of on and off settings for the dipswitches, there are a total of 16 possible EDID selections across 3 different operation modes.
   The three modes are “Internal EDID”, “User EDID” and “External EDID”. There are a total of 6 built-in internal EDIDs and 9 User EDIDs (which can be modified via USB upload). The “External EDID” setting will copy the EDID from the sink that is connected to the Receiver. (See “EDID Management” for more details.)

Front Panel

1. POWER LED: This LED will illuminate to indicate the unit is on and receiving power. LINK LED: This LED will illuminate solidly when a live connection with a compatible Transmitter is active.
2. OPT. IN: Connect to the optical audio output of a device such as a media player or game console using an appropriate optical cable. Audio is sent to the Optical Audio Return output on a connected compatible Transmitter.
3. IR EXTENDER 2: Connect to an IR Extender to extend the IR control range of devices connected to the other end of the HDBaseT connection. Ensure that the remote being used is within direct line-of- sight of the IR Extender.
4. IR BLASTER 1: Connect to the provided IR Blaster to transmit IR signals from the other end of the HDBaseT connection to devices within direct line-of-sight of the IR Blaster.
5. SERVICE: This USB port is reserved for firmware update.
6. RS-232: Connect to a PC, laptop or other serial control device with a 3-pin adapter cable for the extension of RS-232 signals to the Transmitter in “Bypass” mode, or for control this unit when in “Console” mode. Note: Depending on the controlled device connected to the Transmitter side, the Tx and Rx pins might need to be reversed.
7. CONSOLE/BYPASS: This switch controls the operational mode of the RS-232 port. When set to “Bypass”, RS-232 signals will be passed to the connected Transmitter. When set to “Console” the RS-232 port may be used to send commands directly to the Receiver. Note: RS-232 bypass requires both the Transmitter and Receiver to be set to “Bypass” mode.

Rear Panel

1. LAN: Connect to an Ethernet supporting device or to your local network, as appropriate, to extend the network to both ends of the HDBaseT connection.

2. HQ & STD LEDs: These LEDs illuminate to indicate which AVLC mode will be used when AVLC is required. The lower green LED indicates that
   AVLC will use HQ (High Quality) mode. The upper yellow LED indicates that AVLC will use STD (Standard) mode.

3. HDMI OUT: Connect to an HDMI TV, monitor or amplifier for digital video and audio output.

4. CAT5e/6/7 IN: Connect to a compatible, 48V PoH supplying, HDBaseT Transmitter with a single Cat.5e/6/7 cable for transmission of all data signals as well as to power the unit.

IR Cable Pinouts

RS-232 Control

Terminal Block

**Pin| Defini- tion
1| GND
2| Rx
3| Tx
Controlling PC**

**Pin| Defini- tion
1|
2| Rx
3| Tx
4|
5| GND
6|
7|
8|
9|
Serial Port Settings**

Baud Rate| ** 19200
Data Bits| 8
Parity Bit| None
Stop Bits| 1
Flow Control**| None

RS-232 Commands

RX COMMANDS

Description and Parameters

GET TRANSCEIVER COMPRESS RATE 8
Show the current AVLC compression mode.

Note: Commands will not be executed unless followed by a carriage return. Commands are not case-sensitive.

EDID Management

EDID Dipswitch Settings
The EDID dipswitch block provides a way to select the EDID to use with the connected source. By using a combination of on and off settings for the dipswitches, there are a total of 16 possible EDID selections across 3 different operation modes.

1 = Dipswitch in “on” (down) position
0 = Dipswitch in “off” (up) position

**EDID Mode Number| EDID**

Number

| Dipswitch Position
---|---|---
Internal EDID| 1| 1| 1111
2| 2| 1110
3| 3| 1101
4| 4| 1100
5| 5| 1011
6| 6| 1010
User EDID| 1| 7| 1001
2| 8| 1000
3| 9| 0111
4| 10| 0110
5| 11| 0101
6| 12| 0100
7| 13| 0011
8| 14| 0010
9| 15| 0001
Native EDID| | 16| 0000

Detailed EDID information:

Internal EDID (1–6)
There are a total of 6 built-in internal EDID slots covering many standard display configurations. These EDIDs can’t be modified. They are defined as follows:

8-bit

| LPCM 2.0 (297MHz)
UHD/Multi- channel| 3840×2160p@30Hz,

8-bit

| LPCM 7.1 + Bitstream (297MHz)
UHD+/2 channel| 3840×2160p@60Hz,

up to 12-bit

| LPCM 2.0 (594MHz)
UHD+/Multi- channel| 3840×2160p@60Hz,

up to 12-bit

| LPCM 7.1 + Bitstream (594MHz)

User EDID (1–9)
There are a total of 9 User EDID slots which can be modified via USB upload. By default, these slots all contain the same standard EDID:

Native (External) EDID
The Native EDID setting will copy the EDID from the sink that is connected to the Receiver.

EDID Management Tool
This unit uses an EDID Management application which allows the user to copy the EDID from an attached display, edit an existing EDID file stored on the PC or create a basic EDID from scratch. The EDID can then be uploaded to the unit for use.
Please obtain the EDID Management software from your authorised dealer and save it in a directory where you can easily find it.
Before connecting the unit to your PC, please install the appropriate Virtual COM Port Driver depending on your Windows version. Next, install the EDID Management software.
After the installation has successfully completed an icon for it will appear on the windows desktop. Launch the software by double-clicking on the icon and the EDID Management device detection window will open up on your screen.

After launching the software, power the unit on and then connect it to the PC/laptop using a Mini-USB to USB cable. Click on the “Search” button and any detected units will be displayed in the list. Clicking on a detected unit will open the EDID Commander window.

EDID Controller Tab
Mode Select: Under the EDID Controller tab you will see the currently selected EDID slot (based on dipswitch position). The software can’t change this selection, only monitor it.

Save/Upload/Analysis: EDIDs may be saved, uploaded or analysed:

• Save: Any EDID from the unit or a connected HDMI display can be saved to your PC as a *.bin file by selecting the EDID source from the drop down menu and then clicking the “Save ” icon.
• Upload: Previously saved EDID files (*.bin format) can be re-uploaded into any of the “User” EDID slots by selecting the User EDID to replace from the dropdown and then clicking the “Upload” icon. Before accepting the upload, the software will check and verify that the EDID’s header and checksum values are acceptable.
• Analysis: To analyse any EDID stored within the unit, select the EDID to view from the dropdown and click on the “Analysis” icon. From the Analyser window it is possible to open the currently analysed EDID in the EDID Creator by clicking the “Edit” button.

EDID Creator Tab
Select: Click on the EDID Creator tab to begin designing a new EDID from scratch (select the “New” icon), to modify an existing EDID stored on the PC as a *.bin file (select the Load” icon) or to edit an EDID copied from the unit via the EDID Analyser’s edit option.

• Selecting “New” will automatically populate the various EDID fields with basic information that can be easily edited to match the user’s preferences.
• Clicking on the “Load” icon will open a file load window and after the *.bin file has been selected and loaded the EDID fields will be populated with the information from that file. The same will happen when the EDID is copied from the EDID Analyser window.
• Edit: The following tabs provide access to a wide range of EDID information which can be edited:
• Descriptor: This tab allows for the editing of various description and information fields within the EDID file such as Manufacturer Name, Monitor Name, etc.
• PC Timing & SD/HD/UHD: These tabs allow for the selection of the resolutions and refresh rates that the EDID will report as supported.
• Audio1 & Audio2: These tabs allow for the selection of which audio formats, audio frequencies, channels and speaker locations are supported.
• Colour Space: This tab allows for the selection of which colour formats and bit depths are supported, including BT.2020 and HDR support options.
• Others: This tab contains options for supporting 3D and defining the CEC Address.
• Once the user is finished editing or creating an EDID it can be saved to a *.bin file locally or uploaded directly to the unit using the “Save” and “Upload” icons respectively.

System Tab
Configuration & Firmware: Select the System tab to edit the unit’s description (select the “Rename” icon), to reset the unit to factory defaults (select the “Reset ” icon) and to view the unit’s current hardware and firmware version information.

CONNECTION DIAGRAM

SPECIFICATIONS

Technical Specifications

• HDMI Bandwidth 600MHz/18Gbps
• HDBaseT Bandwidth 340MHz/10.2Gbps
• Transmitter
• Input Port 1×HDMI
• Output Ports 1×HDBaseT (RJ45) 1×S/PDIF (TOSLINK)
• Pass-through Ports 1×IR Extender (3.5mm) 1×IR Blaster (3.5mm) 1×LAN (RJ45)
• Control Port 1×USB (Mini-B)
• Receiver Input Ports 1×HDBaseT (RJ45) 1×S/PDIF (TOSLINK)
• Output Port 1×HDMI
• Pass-through Ports 1×IR Extender (3.5mm) 1×IR Blaster (3.5mm) 1×LAN (RJ45)
• Pass-through/Control Port 1×RS-232 (3-pin Terminal Block)
• Pass-through/Control Port 1×RS-232 (3-pin Terminal Block)
• IR Frequency 30–50kHz (30–60kHz under ideal conditions)
• Baud Rate Up to 115200bps
• Power Supply 48V/0.83A DC (US/EU standards, CE/FCC/UL certified)
• ESD Protection Human Body Model: ±8kV (Air Discharge) ±4kV (Contact Discharge)
• Dimensions (Each) 163mm×16mm×78mm (W×H×D) [Case Only] 183mm×16mm×81mm (W×H×D) [All Inclusive]
• Weight 200g
• Chassis Material Aluminum
• Silkscreen Colour Black
• Operating Temperature 0 ˚C–40 ˚C/32 ˚F–104 ˚F
• Storage Temperature -20 ˚C–60 ˚C/-4 ˚F–140 ˚F
• Relative Humidity 20–90% RH (Non-condensing)
• Power Consumption 7W/14W (PoH)

Video Specifications

Supported PC Resolutions (Hz)

| HDMI

Input

| HDBaseT Output
---|---|---
640×480| 60, 72, 75, 85| P| P
720×400| 70, 85| P| P
800×600| 56, 60, 72, 75, 85| P| P
1024×768| 60, 70, 75, 85| P| P
1152×864| 75| P| P
1280×720| 50, 60| P| P
1280×768| 60, 75, 85| P| P
1280×800| 60, 60 (RB)| P| P
1280×960| 60| P| P
1280×1024| 60| P| P
1360×768| 60| P| P
1366×768| 60| P| P
1400×1050| 60, 60 (RB)| P| P
1440×900| 60, 60 (RB)| P| P
1600×900| 60| P| P
1600×1200| 60| P| P
1680×1050| 60, 60 (RB)| P| P
1920×1080| 60| P| P
1920×1200| 60, 60 (RB)| P| P

Supported TV Resolutions (Hz)

| HDMI

Input

| HDBaseT Output
---|---|---
720×480i| 59.94, 60| P| P
720×576i| 50| P| P
720×480p| 59.94, 60| P| P
720×576p| 50| P| P
1280×720p| 50, 59.94, 60| P| P
1920×1080i| 50, 59.94, 60| P| P
1920×1080p| 50, 59.94, 60| P| P
1920×1080p| 23.97, 24, 25, 29.97, 30| P| P
3840×2160p| 24, 25, 30| P| P
4096×2160p| 24, 25, 30| P| P
3840×2160p (YUV 4:2:0)| 50, 60| P| P
3840×2160p| 24, 25, 30 (10, 12-bit HDR)| P| P

(AVLC)

3840×2160p (YUV 4:2:0)| 50, 60 (10, 12-bit HDR)| P| P

(AVLC)

3840×2160p| 50, 60| P| P

(AVLC)

Audio Specifications

Digital (S/PDIF) Output

Sampling Rate (kHz)| 32, 44.1, 48, 88.2, 96, 176.4, 192

Cable Specifications

HDMI Cable             1080p Length                8-bit     12-bit| 4K
---|---
8- bit
Input| 10m| 10m| 5m
Cat. Cable Length| ****

1080p

| ****

4K

---|---|---
Cat.5e| 100m| 70m
Cat.6| 100m| 70m
Cat.7| 100m| 100m

Full HD Video (1080p)

• Up to 1080p@60Hz, 12-bit colour
• Data rates lower than 5.3Gbps or below 225MHz TMDS clock

Ultra HD Video (4K)

• 4K@24/25/30Hz & 4K@50/60Hz (YUV 4:2:0), 8-bit colour
• 4K@50/60Hz (4:4:4, 8-bit) with AVLC active
• Data rates higher than 5.3Gbps or above 225MHz TMDS clock

HDBaseT Features

ACRONYMS

CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue,
Shepperton, Middlesex, TW17 8BA
Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279
Email: sales@cypeurope.com
www.cypeurope.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>