nordlux 2218126047 Outdoor Ceiling Luminaire Installation Guide
- September 23, 2024
- nordlux
Table of Contents
nordlux 2218126047 Outdoor Ceiling Luminaire
Product Information
Specifications:
- Model: VMCTOPUJODMVEFE
- Product Code: 2218126047
- Power Output: 2X15W
Product Usage Instructions
Installation:
Follow these steps to install the product correctly:
- Place the product in the desired location.
- Connect the power cable to a suitable power source.
- Ensure proper ventilation around the product for optimal performance.
Power On/Off:
To power on the product, locate the power button and press it. To power
off, press and hold the power button until the device shuts down.
Volume Control:
Adjust the volume using the dedicated volume control buttons on the
product. Increase or decrease the volume as needed.
Troubleshooting:
If you encounter any issues with the product, refer to the troubleshooting
section of the user manual for solutions. Contact customer support if problems
persist.
Frequently Asked Questions (FAQ)
-
Q: How do I reset the product to factory settings?
A: To reset the product to factory settings, locate the reset button on the device and press it for 10 seconds. -
Q: Can I use this product with external speakers?
A: Yes, you can connect external speakers to this product for an enhanced audio experience. Ensure compatibility before connecting.
Installation Instruction
GRIFFIN CEIL
Mounting instruction
IP4X: Protected against solid objects with a diameter of 1.0 mm or more.
Hazardous parts are shielded from contact being made using wires, etc.
IPX4: Raindrops falling from any angle will not affect the
function/safety of the lamp.
MAX 2X15W
Class 11: The lamp is double-insulated and does not need to be connected
to the yellow/green earth wire.
Do not exceed the maximum wattage.
The lamp is only suitable for connecting directly to the mains.
The mounting instruction must not be discarded.
IMPORTANT! Always shut off power to the circuit before starting installation work. In some countries, electrical installation work may only be carried out by a authorized electrical contractor. Contact your local electricity authority for advice.
Disposal of waste equipment by users in private households in the European Union. This symbol indicates that this product mus not be disposed of with your other household waste. Electrical and electronic equipment contain substances which may cause damage to human health and environment if not recycled correctly. It is your responsibility to hand over to a designated collection point for recycling of waste electrical and electronic equipment. When handing over for correct recycling you help to prevent these products straining nature and environment unnecessarily and to protect human health. For more information regarding correct disposal, please contact your local city office, your household waste disposal service or the store where you purchased this product.
In the Nordic Countries, outdoor lights must be mounted by an authorised electrician.
www.norux.com
Nordlux A/S • Østre Havnegade 34 • DK- 9000 Aalborg
Mounting instruction
We congratulate you on your new outdoor lamp!
Stainless steel
- Remember to take care of your lamp. Just follow the guidelines below.
- The shiny, uniform and decorative surface of stainless steel makes it very suitable for outdoor use.
- It is an alloy consisting of iron, chrome and nickel. During bath pickling, a thin, rustproof oxide layer forms on the surface.
- The surface is continually vulnerable to atmospheric conditions and from other effects of the close environment. This means that the lamp must be regularly maintained if its surface is to remain shiny and untarnished by rust.
- Before setting it up, treat your lamp with acid-free oil, and dry it off with a soft cloth. Repeat this three or four times a year.
Stainless steel lamps are not recommended for use in aggressive
environments such as coastal, agricultural or industrial areas.
Copper, Brass and Tombac fixtures
Our copper, brass and tombac fixtures are made from respectively solid copper,
brass, and tombac. The mechanical machining will leave small scratches in the
surface, as well as residues of rinse aid. This rapidly disappears in the
patina process. After the first rain showers, the copper/brass / tombak
surface WII appear stained, but the aerated air and moisture will soon the
lamp appear with dark brownish color. Over the years, the material copper will
get a beautiful patina-green color, and brass/tombac will get a darker and
more uniform color. The uniformity of the patina surface, as well as the rate
at which the process occurs, is dependent on the environment that affect the
fixture.
Hot-galvanized lamps
The zinc treatment of the steel lamps is executed manually in plants. The
temperature of the melted zinc is about 460 degrees. When the lamps are dipped
in melted zinc a reaction between the metalls occurs, which develops alloys in
the surface.
The lamp and the components of the lamp are manually dipped in the hot zinc. This treatment leaves variations in the coating in the form of partly an uneven surface and partly minor formations of drops.
Thin »zinc curtains« might also occur on the surface and they show as a thin film which hangs down from the edge of the lamp. This film can easily be removed or brushed off with a soft brush.
Condensation
Condensation is a natural phenomenon arising under specific atmos-pheric
conditions. Damp heat and cold air meet, which causes condensation of water on
the surface.
When water heats up it leads to rising water vapour, which will be able to affect electric components.
Condensation is not included by Nordlux warranty unless it is possible to prove that a technical /production error in the lighting causes entry of water.
In case of condensation please check:
- If the lighting is mounted according to instructions. Washers should seal tightly. Make sure to tension screws and lenses.
- In garden lighting rising damp from the ground may cause condensation in the metal post. This problem can be defeated by filling sealing material into the metal post.
Aluminum fixtures
Our aluminum light fixtures are made from die-cast and/or extruded aluminum, where the light fixture’s design determines whether both types Of materials or just one Of them, are used for different parts Of the same light fixture. Aluminum light fixtures in raw aluminum are subsequently coated with a special clear coat, which seals the surface to safeguard against corrosion. Painted aluminum light fixtures are powder-coated and have a uniform and smooth surface.
To avoid the light fixture tarnishing, it is recommended to clean and wipe the light fixture after mounting and repeat this process 3-4 times each year. This is done with a regular cleaning agent. Black light fixtures which are bleached by strong sunlight can also benefit from treatment with silicone spray as needed, to maintain the black color. Mounting light fixtures in coastal, agricultural, or industrial areas is not recommended, as these aggressive surroundings may cause the light fixture to corrode, which may entail spalling, bubbles in the surface, and a whitish incrustation on the light fixture’s surface.
- It is highly important that drainage holes are kept free of impurities ifany.
BEFORE ASSEMBLING THE BOLLARD AGAIN DO REMEMBER TO WIPE OFF ALL PARTS!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>