Scantronic 9449 Hardwired Control Panel User Guide
- June 6, 2024
- Scantronic
Table of Contents
Scantronic 9449 Hardwired Control Panel
TO FULL SET
Key-in your four digit user code (shown as ???? at left). The exit tone
starts. Leave premises via the designated exit door. Exit tone stops after
preset time (or within seven seconds of pressing the exit terminate button).
Your alarm system is SET.
TO PART SET
Your alarm system may have been installed to allow you to have part of the
premises set while other area(s) are off. To part set the system key in 2 then
ENTER, followed by your user code. Note that the part set exit tone is usually
a buzzer sound, but your system may be programmed to silent set.
Note: If you enter your user code incorrectly four times in a row then
the system will raise a tamper alarm. See opposite.
IF A ZONE LIGHT GLOWS WHILE SETTING
If, during setting, the sounder gives an interrupted tone and a zone light
glows, then a detector is being triggered (maybe a door or window is open).
Key in your user code to stop the tone.
Check the indicated zone(s) and if possible correct the cause of the alarm.
Try setting the system again. If the fault persists, call your alarm
installer. Note that it may be normal for certain zone lights to glow as you
walk past detectors on the way out of your premises.
If the Entry/Exit light glows, the exit door may be open. Leave the premises
and close the door. The interrupted tone should change to a steady tone when
the door is closed and the system then sets as normal.
TO UNSET
Full Set: Enter by the designated entry door. Entry tone starts. Go to control
panel. Key-in your user code. System is OFF.
Part Set: Entry tone starts. Go to control panel. Key-in your user code.
System is OFF.
Note : The system has a preset entry time to allow you to get to the
panel. If you find that you do not have enough time to reach the control
panel, ask your Installer to increase the entry time.
AFTER AN ALARM
Fire Alarm: The system gives a fire alarm by sounding a warbling tone from the
internal sounder.
- Evacuate the premises and call the Fire Brigade. Do not attempt to unset the alarm.
- When the premises are safe, follow the instructions below.
To switch the bells off:
Key-in your user code. The sounders will stop and the zone light(s) for the
detectors that triggered the alarm will glow.
Tamper or Panic Alarm:
If you hear the internal sounder when the system is off then look at the
control panel:
If the Tamper light glows then key-in your user code to stop the sounder. Call
your alarm installer for service.
If the tamper light is off see if a PA zone light is glowing. Deal with the
cause of the alarm first. Next, reset the panic button, then switch the alarm
system bells off and reset the system (see below).
Reset system: You must reset the system before it can be used again. If the
Service LED is OFF then you can reset the system yourself. Key-in your access
code again. All the zone lights should go off. The system is now ready for
use.
If the Service LED is ON, you must call for an engineer to reset the system.
Remote Reset:
If your alarm is connected to a central station then the system may use remote reset (ask your Installer). With this method the keypad displays a special four digit code. Report this code to the central station, who then give you another code to let you to reset the system. Have a pencil and paper ready to note down the code.
-
Key in your user code to silence the bells.
The display shows the zone and Service LEDs ON. -
Key in your user code again.
The display shows a four digit code by lighting the zone lamps one at a time. The small numbers to the right of the lamps give the digits. The keypad sounder gives a short tone each time the digit changes. (If there is no light glowing then the digit is “zero”.) -
Note down the code. If necessary, press Enter to make the keypad repeat the code.
-
Report the code to the central station. The central station will give you a new four digit code, the “anti-code”, note it down.
-
Enter the code given by the central station. The Service light goes out.
-
Key in your user code. The system is now ready for use.
TO CHANGE YOUR USER CODE
Your system provides two separate four digit user codes. When the system is
new, the user codes are “1234” and “0000”. Change the “1234” user code
immediately to a number that only you know. The new code can be ANY four digit
code you choose. The “0000” user code is inactive and will not operate the
system. To activate the second user code change the “0000” to another four
digit number. Do not use the same number for both user codes. To inactivate
the second user code again, change it back to “0000”.
Duress Code: Your system provides a Duress Code. When the system is new the
code is inactive, and set to “✽✽✽✽”. To activate the code change it to a
number you can remember, using the same method as changing the access codes.
Do not use “9999” or the same number as your other access codes. To inactivate
the duress code change it back to “✽✽✽✽”. If your system is connected to a
central station, then it will send a silent signal when you unset your system
using the duress code.
TO TEST BELLS
Make sure system is unset before starting the test. Key in 4 then ENTER
followed by your user code. The internal sounders will operate for three
seconds and then the external sounder and strobe will operate for 10 seconds.
TO WALK TEST
Key in 5 then ENTER, followed by your user code. The internal sounder gives a
steady tone.
Open and close the Exit/Entry zone and Zones 1 to 7. Each time you open a
zone, the zone light flashes and the internal sounder gives a pulsing tone.
You cannot test the ‘Tamper Circuits’, fire alarms, 24 Hour zones or panic
buttons without causing an alarm.
To stop a walk test, key-in your access code.
TO OMIT A DETECTOR
You may need to temporarily set the system with one or more detectors omitted.
Key in the zone number followed by OMIT for all the zones you want to omit and
then key in your user code. The system flashes the light(s) of the omitted
zone(s) during the exit time and then sets. Note that you cannot omit a panic
button, nor can you omit a 24 hour zone while the system is unset.
The system will not raise an alarm if any omitted detector is triggered during
this setting cycle. The system will reinstate the detector(s) and set nor-
mally the next time you set the system.
TO SWITCH CHIME ON OR OFF
Key in 7 then ENTER, followed by your user code to switch Chime on or off.
When Chime is on, the internal sounder chimes when the chime zones operate.
Note that the Installer must program your chime zones.
TELEPHONE LINE FAILURE
If you see the Fault and Service LEDs flashing, and a short tone every few
seconds then the system has detected a fault on the telephone line connecting
the system to the central station. Key in your user code to stop the tone. The
Fault and Service LEDs will continue to flash until the telephone line fault
is corrected.
DISPLAYING THE LAST 10 EVENTS
You can display the ten most recent alarms and tampers stored in the system’s
log.
Key in 8 plus ENTER followed by your user code. The display shows the most
recent zone to cause an alarm, or lights the Tamper LED.
Key in 1 to show earlier events or 3 to see more recent events. The display
shows earlier and later alarms/tampers. The keypads give a short tone when you
reach the end of the log.
Press OMIT or ENTER to leave the log.
KEYPAD PA
You can start a Panic Alarm by pressing keys 1 and 3 together on the keypad.
SETTING THE INTERNAL CLOCK
The system has an internal clock. If you have a log printer, the log shows
events occurring at the correct time. (The Installer may have already set the
clock for you.) If you need to change the time and date:
Make sure the system is unset.
Key in 9 plus ENTER followed by your user code. The keypad displays the digits of the date and time one by one on the zone and tamper LEDs. The keypad sounder beeps each time the system shows a new digit. The EE zone LED represents “1” and the Tamper LED represents “9”. If all LEDs are off when the keypad beeps then the digit “0” (zero). When the keypad has completed showing the date and time, the zone and tamper LEDs go out, and the system waits for you to enter the new date and time.
EITHER press ENTER to leave the time as it is OR: Key in the day,
month, hours and minutes in numerical format, and then press ENTER.
For example, to change the date and time to 8 August, 1:30 pm, key in “08 08
13 30 ENTER”. The keypad gives a double beep to show it has accepted the new
date and time.
FAULT FINDING
The diagrams below and on the opposite page shows the meaning of some of the
displays you may see on your keypad.
© Scan tronic Ltd. 1997
Every effort has been made to ensure that the contents of this book are
correct, errors and omissions excepted. However, neither the authors nor
Scantronic accept any liability for loss or damage caused or alleged to be
caused directly or indirectly by this book. The contents of this book are
subject to change without notice. Printed and published in the U.K.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>