VIBE442N Vibe Amplifier

“`html

Specifications

• Model: VIBE1100N, VIBE1400N, VIBE2102N,
  VIBE442N, VIBE452N, VIBE452N.6

• Channels: Mono Channel, 2 Channel, 4
  Channel

• RMS at 4 Ohms: Varies by model

• MAX at 4 Ohms: Varies by model

• RMS at 2 Ohms: Varies by model

• Min. Speaker Impedance: 2 Ohm

• T.H.D.: 0.05%

• Frequency Response: Varies by model

• Input Sensitivity: Varies by model

• Input Impedance: 20 k Ohm

• S/N Ratio: >95dB

• Channel Separation: >60dB

• Crossover Filters: Low Pass, High Pass, Band
  Pass

• Bass Boost: +10dB to +18dB

• Dimensions (In.): Varies by model

• Fuse(s): Varies by model

Product Usage Instructions

Precautions

1. Before drilling or cutting any holes, carefully investigate
   your car’s layout to avoid damaging fuel lines, gas tanks,
   hydraulic lines, and electrical wiring.

2. Do not operate the amplifier when it is unmounted. Securely
   attach all audio components.

Installation

1. Find a suitable location in the vehicle to mount the
   amplifier.

2. Ensure sufficient airflow around the intended mounting
   location.

3. Bolt the amplifier to the mounting surface.

4. Connect the power ground terminal to the nearest chassis point.
   Keep this ground wire less than 39 inches in length and use 8 gauge
   wire.

5. Connect the remote terminal to the remote output of the head
   unit using 14 gauge wire.

6. Install an empty fuse holder within 12 inches of the battery
   and run 8 gauge or larger high-quality cable from this fuse to the
   amplifier location.

7. Connect this cable to the BATT connection on the amplifier. If
   using multiple amplifiers, ensure proper power distribution.

Frequently Asked Questions (FAQ)

Q: Is it safe to use the amplifier with an impedance lower than

2 Ohms?

A: It is not recommended to use speaker impedance lower than 2
Ohms as it may lead to overheating or damage to the amplifier.

Q: What is the recommended fuse rating for the amplifier?

A: The recommended fuse rating varies by model. Refer to the
user manual or specifications for the correct fuse rating for your
specific amplifier model.

“`

Visit Our Website
SCAN ME
PyleUSA.com
Amplifiers
USER GUIDE

You’ve made a great choice with the Lanzar Vibe amplifier–a quality product designed and engineered to provide many years of uncompromised musical service. Vibe amplifiers feature the latest technology, including a DC to DC Switching Power Supply, offering the headroom needed for the most demanding peaks and dynamic ranges in modern CDs and recordings.

TABLE OF CONTENTS

FEATURES

3

TECHNICAL SPECS

3

PRECAUTIONS

4

INSTALLATION

4

CONTROLS

5

SYSTEM WIRING

8

TROUBLESHOOTING

11

CLEANING AND STORAGE

12

REGISTER PRODUCT

13

PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

California Prop 65 Warning
WARNING:
This product may expose you to chemicals, which is known to the state of California to cause cancer, birth defects and other reproductive harm. Do not ingest.
For more info go to: www.P65warnings.ca.gov

2 www.PyleUSA.com

FEATURES: · MOSFET Switches: Maintain rated power over a wide range of battery voltages. · Regulated PWM Power Supplies: Stiffly regulated for consistent performance. · 2-Ohm Stable Stereo Operation · Variable Input Level Controls: For each pair of channels. · High and Low Pass Crossover Controls · Thermal and Speaker Short Protection Circuits · Power and Protection LED Indicators · Bass Boost Circuitry · Compatibility: Stereo, Bridge Mode, and Tri-Mode System applications. · Silver-Plated Power, RCA, and Speaker Connectors · High- Efficiency Heavy Aluminum Heatsink · Bass Boost Remote Control

TECHNICAL SPECS

MODEL

VIBE1100N VIBE1400N VIBE2102N

Mono Channel Mono Channel

2 Channel

Amplifier

Amplifier

Amplifier

VIBE442N
4 Channel Amplifier

VIBE452N VIBE452N.6

4 Channel

4 Channel

Amplifier

Amplifier

RMS at 4 Ohms 1x800W 1x1000W 2x1500W 4x625W 4x1250W 4x1250W

MAX at 4 Ohms N/A

N/A

2x3000W 4x1250W 4x1500W 4x1500W

at 4 Ohms Bridged N/A

N/A

1x6000W 2x2500W 2x3000W 2x3000W

RMS at 2 Ohms 1x1600W 1x2000W 2x2400W 4x1000W 4x2000W 4x2000W

Min. Speaker Impedance

2 Ohm

2 Ohm

2 Ohm

2 Ohm

2 Ohm

2 Ohm

T.H.D.

0.05%

0.05%

0.05%

0.05%

0.05%

0.05%

Frequency Response 15Hz-150Hz,-1dB 15Hz-150Hz,-1dB 10Hz-40kHz,-1dB 10Hz- 40kHz,-1dB 10Hz-40kHz,-1dB 10Hz-40kHz,-1dB

Input Sensitivity 200mV-9000mV 200mV-9000mV 200mV-6000mV 200mV-6000mV 200mV- 6000mV 200mV-6000mV

Input Impedance 20 k Ohm 20 k Ohm 20 k Ohm 20 k Ohm 20 k Ohm 20 k Ohm

S/N Ratio

95dB

95dB

95dB

95dB

95dB

95dB

Channel Separation

N/A

N/A

60dB

60dB

60dB

60dB

Crossover Filters
Low Pass High Pass Band Pass

35Hz-250Hz N/A N/A

35Hz-250Hz N/A N/A

40Hz-350Hz 40Hz-3kHz
N/A

40Hz-350Hz 40Hz-3kHz
N/A

40Hz-350Hz 40Hz-3kHz
N/A

40Hz-350Hz 40Hz-3kHz
N/A

Bass Boost

+10dB

+10dB

+18dB

+18dB

+18dB

+18dB

Dimensions (In.) 10.25×2.36×7.87 10.25×2.36×9.45 10.25×2.36×24.41 10.25×2.36×18.90 10.25×2.36×20.47 10.25×2.36×20.47

Fuse(s)

10Ax2

15Ax2

30Ax4

40Ax2

35Ax3

35Ax3

www.PyleUSA.com 3

PRECAUTIONS 1. Before drilling or cutting any holes, carefully investigate your car’s layout to
avoid damaging fuel lines, gas tanks, hydraulic lines, and electrical wiring. 2. Do not operate the amplifier when it is unmounted. Securely attach all audio
system components within the vehicle to prevent damage, especially in the event of an accident. 3. Do not mount the amplifier in a manner that leaves wire connections unprotected or in a pinched condition. Ensure adequate ventilation for the amplifier. 4. Before making or breaking power connections, disconnect the vehicle battery. Ensure the head unit or other equipment is turned off while connecting the input jacks and speaker terminals. 5. If replacing the power fuse, only use a fuse identical to that supplied with the system. Using a fuse of a different type or rating may result in system damage not covered by the manufacturer’s warranty.
INSTALLATION 1. Find a suitable location in the vehicle to mount the amplifier. 2. Ensure sufficient airflow around the intended mounting location. 3. Bolt the amplifier to the mounting surface. 4. Connect the power ground terminal to the nearest chassis point.
Keep this ground wire less than 39 inches in length and use 8 gauge wire. 5. Connect the remote terminal to the remote output of the head unit using 14
gauge wire. 6. Install an empty fuse holder within 12 inches of the battery and run 8 gauge
or larger high-quality cable from this fuse to the amplifier location. 7. Connect this cable to the “BATT” connection on the amplifier. If using multiple
amplifiers, use separate cables with their own fuse at the battery or a #0 or

2 cable from the fuse holder at the battery to a distribution block near the

amplifier’s location. 8. Connect all line inputs and outputs using high- quality RCA cables. 9. Insert fuse(s) at the battery fuse holder(s). 10. Recheck all connections before powering up. 11. Set all level controls to their least sensitive positions and adjust all crossover controls, switches, etc., to the desired frequency or position. 12. Power up the system and set the head unit volume to about the 2 o’clock position, then adjust the amplifier’s level controls for maximum output. 13. Further fine-tuning of the various controls may be necessary to achieve the desired sound quality.
4 www.PyleUSA.com

CONTROLS VIBE1100N – VIBE1400N

Input Level Controls Enables matching of input levels to the output levels from the head
unit (or other signal source).
Phase Shift Allows you to change the phase of your subwoofer from 0 to 180 degrees to help compensate for timing differences between drivers.
Remote Control
Bass EQ Control Increases sound level in lower
frequencies by up to 10 dB.

Power & Protection Indicators Provides instant information on the status of the amplifier, including short-circuit and thermal overload alerts.
Low Pass Filter This control limits the frequencies that will be distributed to the speakers to those below the value set within the range of 35-250 Hz.
Subsonic Filter Adjustable between 15 Hz and 35 Hz.
www.PyleUSA.com 5

CONTROLS VIBE2102N

Input Level Controls Enables matching of input levels to the output levels from the head
unit (or other signal source).
Bass EQ Control Increases sound level in lower
frequencies by up to 18 dB.
Low Pass Filter This control limits the frequencies that will be distributed to the speakers to those below the value set within the range of 40-350 Hz.
Crossover Mode Selector Determines the mode of the built-in crossover: Low Pass (permits only low-frequency signals to
pass to speakers), High Pass (permits only highfrequency signals to pass to speakers), or Full.
6 www.PyleUSA.com

Power & Protection Indicators Provides instant information on the status of the amplifier, including short-circuit and thermal overload alerts.
Remote Control
High Pass Filter When the Crossover Mode Selector is set to High Pass Mode, this control limits the frequencies that will be distributed to the speakers to those above the value set within the range of 40 Hz to 3 kHz.

CONTROLS VIBE442N – VIBE452N – VIBE452N.6

Input Level Controls Enables matching of input levels to the output levels
from the head unit (or other signal source).
Bass EQ Control Increases sound level in lower
frequencies by up to 18 dB.
Crossover Mode Selector Determines the mode of the
built-in crossover: Low Pass (permits only low-frequency
signals to pass to speakers), High Pass (permits only high- frequency
signals to pass to speakers), or Full.

Power & Protection Indicators Provides instant information on the status of the amplifier, including short-circuit and thermal overload alerts.
Remote Control
High Pass Filter When the Crossover Mode Selector is set to High Pass Mode, this control limits the frequencies that will be distributed to the speakers to those above the value set within the range of 40 Hz to 3 kHz.
Low Pass Filter This control limits the frequencies that will be distributed to the speakers to those below the value set within the range of 40-350 Hz.
www.PyleUSA.com 7

SYSTEM WIRING Mono Block Configuration VIBE1100N – VIBE1400N
2 Channel Stereo Configuration VIBE2102N
8 www.PyleUSA.com

SYSTEM WIRING 2 Channel Bridged Mode Configuration VIBE2102N
2 Channel Tri-Mode Configuration VIBE2102N
www.PyleUSA.com 9

SYSTEM WIRING 4 Channel Stereo Configuration VIBE442N – VIBE452N – VIBE452N.6
4 Channel Bridged Mode Configuration VIBE442N – VIBE452N – VIBE452N.6
10 www.PyleUSA.com

SYSTEM WIRING 4 Channel Tri-Mode Configuration VIBE442N – VIBE452N – VIBE452N.6
TROUBLESHOOTING AMPLIFIER WILL NOT POWER UP · Check for a good ground connection. · Ensure that the remote DC terminal has at least 3V DC. · Verify battery power on the + terminal. · Inspect all fuses. · Check that the Protection LED is not lit. If it is, shut off the amplifier briefly and
then repower it. HIGH HISS OR ENGINE NOISE (ALTERNATOR WHINE) IN SPEAKERS
· Disconnect all RCA inputs to the amplifier(s). If hiss/noise disappears, then
plug in the component driving the amplifier and unplug its inputs. Continue until the faulty/noisy component is identified.
· Set the amplifier’s input level as low as possible. The best subjective S/N ratio
is obtainable this way. Try to drive the signal level from the head unit as high as possible.
www.PyleUSA.com 11

PROTECTION LED COMES ON WHEN THE AMPLIFIER IS POWERED UP
· Check for shorts on speaker leads. · Ensure the volume control on the head unit is turned down low. · Remove speaker leads and reset the amplifier.
If the Protection LED still comes on, the amplifier may be faulty.
AMPLIFIER(S) GETS VERY HOT
· Verify that the minimum speaker impedance for the model is correct. · Check for speaker shorts. · Ensure good airflow around the amplifier. In some applications, an external
cooling fan may be required.
DISTORTED SOUND
· Verify that the Level control(s) is set to match the signal level of the head unit. · Ensure all crossover frequencies are properly set. · Check for shorts on the speaker leads.
HIGH SQUEAL NOISE FROM SPEAKERS Ensure all connections are secure and no components are loose.
CLEANING AND STORAGE CLEANING Exterior Surface: To clean the exterior surface of your amplifier, use a soft, dry cloth. If necessary, slightly dampen the cloth with water or a mild detergent. Avoid using any harsh chemicals, solvents, or abrasive materials, as these can damage the surface finish.
Vents and Openings: Ensure that the ventilation openings are free from dust and debris. Use a can of compressed air to gently blow out any accumulated dust, taking care not to force debris deeper into the unit.
12 www.PyleUSA.com

STORAGE Disconnect All Cables: Before storing the amplifier, disconnect all power, input, and output cables. Store these cables separately to avoid tangling and potential damage.
Cool, Dry Environment: Store the amplifier in a cool, dry place, away from direct sunlight, heat sources, and moisture. Extreme temperatures and humidity can affect the performance and longevity of the unit.
Protect from Dust: If possible, store the amplifier in its original packaging or a dust cover to protect it from dust accumulation. Alternatively, place it in a padded storage case.
Avoid Stacking: Do not stack heavy objects on top of the amplifier during storage, as this can cause physical damage to the unit.

Register Product

Thank you for choosing PyleUSA. By registering your product,

you ensure that you receive the full benefits of our exclusive

warranty and personalized customer support.

Complete the form to access expert support and to keep your

PyleUSA purchase in perfect condition.

PyleUSA.com/register

www.PyleUSA.com 13

Questions or Comments? We are here to help! Phone: 1.718.535.1800
PyleUSA.com/ContactUs

References

• P65warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>