Lanzar HTGX6BTH 3 Way Active Crossover with Wireless BT Audio Connectivity User Guide
- June 6, 2024
- Lanzar
Table of Contents
Lanzar HTGX6BTH 3 Way Active Crossover with Wireless BT Audio
Connectivity
Specifications
Features:
- Exclusive Infinite 3 Way Crossover Design
- 2- & 3-Way Asymmetrical Crossover
- Adjustable Bass Shaper
- Wireless BT Audio Connectivity
- 18dB/Octave Low Pass Filter
- 12dB/Octave High Pass Filter
- X1 – X20 Frequency Multiplier
- RCA Mono/Stereo Subwoofer Audio Output
- Adjustable Audio Output Level
- Subwoofer Phase switch 0-180 degree
- Front/Rear RCA Pre-Amp Inputs
- Parallel Audio Input Switch
- Gold Plated RCA Connections
- DC 12 Volt with Remote Trigger
Wireless BT Streaming:
- Built-in BT for Wireless Music Streaming
- Simple & Hassle-Free Pairing
- Works with All of Today’s Latest Devices Smartphones, Tablets, Laptops, Computers, etc.
- Wireless BT Version: 4.0
- Wireless BT Network Name: ‘LANZAR HERITAGE’
- Wireless Range: Up to 32’ ft.
What’s in the Box:
- 3 Way Active Crossover
Technical Specs:
- Construction Material: Iron
- Power Output: DC 12V
- Pre-Amp Output: 9V RMS
- Power Dimensions (L x W x H): 6.9” x 5.3”x 1.7′ -inches
FUNCTIONS
-
Power LED: Red light indicates power ON.
-
Front Channel Highpass Frequency Control : This detented knob controls the frequency of the front Highpass output from 32-400Hz
-
Multiplier : This switch multiplies the Front Channel Highpass Frequency Control from either 32-400Hz (x1) to 600-8kHz (x20).
Switch to the left to multiply (x1) and to the right to multiply (x20). -
Parallel Input: This switch combines the Front and Rear inputs if only one RCA pair is available for signal input. Switch to the left to PARALLEL INPUT inputs and to the right to use separate inputs.
-
Rear Channel Highpass Frequency Control: This detented knob controls the frequency of the Rear Highpass output from 32-400Hz.
-
Phase: This switch allows you to invert the subwoofer phase from 0 to 180′.
-
Sub Frequency Control: This detented knob controls the frequency of the Subwoofer output from 32-400Hz.
-
Bass Boost: This knob allows for a boost at 40Hz up to 12dB.
-
Level: Allows you to control levels up to 18dB.
-
Mode: Change the subwoofer output from stereo to mono thus facilitating single Subwoofer installations.
- Front Input: Gold-plated RCA inputs. Plugin the RCA cables from the Front channel of your radio here.
- Rear Input: Gold-plated RCA inputs. Plugin the RCA cables from the Rear channel of your radio here.
- Mixed Output: Gold-plated RCA inputs. Full range output.
- Sub LowPass: Gold plated RCA outputs. Run the RCA cable to the Subwoofer amplifier RCA input.
- Remote Sub Level: Plug the remote sub-level control into this jack. Run the remote sub-level control to a position in the passenger area to allow control of the sub-level.
- Rear HighPass: Gold plated RCA outputs. Run the RCA cable to the Rear Speaker or midrange speaker amplifier RCA input.
- Front HighPass: Gold plated RCA outputs. Run the RCA cable to the Front speaker or tweeter amplifier RCA input.
- Power: After connecting the Power, Ground, and Remote wires to the Power lock connector, plug the connector in here.
- Wireless BT: BT wireless receiver. Set up Wireless BT Streaming
Make the device you are connecting to visible.
Open Settings.
Select BT to ON.
Toggle the button and tap Scan to turn on Wireless BT and scan for devices.
Select the device you want to connect to from the list “LANZAR HERITAGE”.
Mounting
To prevent damage to the crossover while driving, mount it in a secure place.
Choosing the appropriate location will depend upon your vehicle and the
complexity of your system design. Typical mounting locations for your new
crossover include the trunk or passenger compartment (floor or under seat).
Never mount the component in a location that would subject it to immersion or
exposure to water.
Once a location has been chosen, securely mount the crossover with four
mounting screws. Be Careful! Inspect the area underneath to be sure you are
not drilling into wires, etc. that could be damaged by the drill bit or
screws.
Locations for mounting screws
System Diagram
Troubleshooting
Low Output From One Brand:
Check crossover frequencies for low pass points set higher than high pass
points and check gain control on the affected amplifier(s). If low output is
still a problem contact your local authorized dealer.
Callfomla Prop 65 Warning
WARNING:
This product can: ins Nickel carbonate which Is known to 1he stole of to
cause concern birth defects and Oihe< reproductive harm. Do not Ingest Formcn
lnt’o go to: www.P~gs.cca.gov