STELPRO UTB Series Electric Baseboard Owner’s Manual

STELPRO UTB Series Electric Baseboard

Product Specifications:

• Models: UTB0502W, UTB1002W, UTB1502W, UTB2002W Manufacturer: STELPRO
• Website: www.uniwatt.ca
• MATERIAL REQUIRED: Phillips screwdrivers, screws, twist-on wire connectors, wire strippers

Product Usage Instructions

1. Installation:

CAUTION:

1. Do not install the heater in any position other than as shown in the manual.
2. Wiring procedures should comply with the National Electrical Code (NEC) and local codes.
3. Avoid storing flammable items near the heater.
4. Avoid installing the heater against combustible surfaces.
5. Keep a safe distance from curtains and other furnishings.
6. Avoid contact with combustible materials.
7. Do not bypass the thermal protection [G].

CLEARANCE REQUIRED:

• Top: 6 inches (15 cm)
• Sides: 3 inches (7.5 cm)
• Bottom: 1 inch (2.5 cm)

2. Preparing the Baseboard:

WARNING: Turn off the power supply before proceeding.

1. Place the baseboard face down to protect the flooring.
2. Unscrew the junction box cover and remove it.
3. Pull out the wires connected by a twist-on wire connector.

3. Connecting the Wiring:

1. Connect the grounding wire to the green screw provided.
2. Connect the baseboard and power supply wires according to the diagram provided.
3. Tighten wires into the twist-on connectors to ensure secure connections.

4. Attaching the Baseboard to the Wall:

1. Mount the baseboard on the wall using at least four mounting holes.
2. If no studs are available, anchors may be required. Do not over-tighten.

5. Operation and Maintenance:

WARNING: Ensure proper installation before use. Fins are sharp, avoid direct contact.

• Clean annually or as needed using a damp cloth and non-abrasive dish soap to remove dust build-up.
• All other servicing should be performed by qualified service personnel.

Frequently Asked Questions

Q: Can I install the baseboard heater against a combustible surface?
A: No, do not install heaters against combustible low-density cellulose fiberboard surfaces.

Q: How often should I clean the baseboard heater?
A: Clean the baseboard heater once a year or as required using a damp cloth and non-abrasive dish soap to remove dust build-up.

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1.  Read all instructions before using this heater.
2.  A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
3.  This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains away from the heater.
4. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
5. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
6. This product must be installed by a qualified person and connected by a certified electrician, according to the electrical and building codes effective in your region and NEC.

The following instructions must be adhered to avoid personal injuries or property damages, serious injuries, and potentially fatal electric shocks.

1. Protect the heating unit with the appropriate circuit breaker or fuse, by the nameplate.
2. Make sure the line voltage (volt) is consistent with that indicated on the unit’s nameplate.
3. This unit must be grounded.
4. Switch off the power at the circuit breaker/fuse before installing, repairing, and cleaning the unit.
5. Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
6. Do not install the unit where objects or furniture could be damaged by the heat.
7. Respect distances and positions indicated in the installation section.
8. If the installer or user modifies the unit, they will be held responsible for any damage resulting from this modification, and the CSA/ UL certification could be void.
9. When starting up the unit for the first time or after a long period, it is normal that it produces some temporary odors and whitish smoke.
10. Do not install it on a wall behind a door.
11. Make sure the electrical connections are sturdy and have been executed correctly. Failure to comply with this directive could result in a fire.

INSTALLATION

CAUTION

1. Do not install a heater in any position other than as shown in this manual.
2. Wiring procedures and connections should be by the National Electrical Code (NEC) and local codes.
3. To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater.
4. Do not install heaters against combustible low-density cellulose fiberboard surfaces.
5. Do not install heaters below an electrical convenience receptacle.
6. Use only copper branch circuit conductors.
7. CAUTION High temperature, keep electrical cords, drapes, and other furnishings away from the heater.
8. Keep drapes at a distance of at least 6 in. (15 cm) from the unit.
9. Do not install the unit in contact with combustible materials
10. Do not remove or bypass the thermal protection [G].

To ensure the safe operation of the heating unit, the clearance specifications shown in the drawing below must be met.

PREPARING THE BASEBOARD

WARNING : Turn off the power supply

• Place the baseboard face down as shown, taking care to protect the flooring beforehand.
• Unscrew the junction box cover [A] and remove it. Use the one on the left or right, according to your needs.
• Gently pull the two (2) wires connected by a twist-on wire connector [B] until they come out of the junction box.

CONNECTING THE WIRING

• Connect the grounding wire firmly with the green screw [E] provided.
• Connect the baseboard and power supply wires [C] according to the connection diagram. Tighten wires into the twist-on connectors [D] to make sure the connections are secure before pushing them back into the junction box.
• Screw the junction box cover [A] back on, making sure to place the cable in the clearance provided in the cover [I].

Note: If the installation is done in a knockout [J], use a wire clamp to secure the cable.

NET VOLUME (cm 3 )

 | RIGHT JB| LEFT JB
WITHOUT OPTION| 506.00| 535.49
SIBT1W| 479.91| 509.41

ATTACHING THE BASEBOARD TO THE WALL

• Attach the baseboard to the wall using at least four (4) mounting holes [F]. If no studs are available, anchors may be required. Do not over-tighten.

OPERATION AND MAINTENANCE

WARNING: The baseboard must be properly installed before it is used. Fins are sharp and may cause cuts, do not touch.

1. Once a year, or as required, use a damp cloth and non-abrasive dish soap to remove any dust build-up. All other servicing is to be done by qualified service personnel.
2. Before cleaning, make sure the power has been turned off at the circuit breaker panel, and wait until the elements have cooled before cleaning the unit or removing the front cover.
3. If the unit is installed in a dusty area, use a vacuum cleaner to remove the dust.
4. Replace the front cover [H] if it was removed.
5. Restore the power at the circuit breaker.

STELPRO LIMITED WARRANTY

This limited warranty is offered by Stelpro Design Inc. (“Stelpro”) and applies to the following product made by Stelpro: model UTB. Please read this limited warranty carefully. Subject to the terms of this warranty, Stelpro warrants its products and their components against defects in workmanship and/or materials for the following periods from the date of purchase: 2 years and 10 years warranty on the heating element (for the first end-user. This warranty applies only to the original purchaser; it is non-transferable and cannot be extended.
CLAIM PROCEDURE
If at any time during the warranty period, the unit becomes defective, you must cut off
the power supply at the main electrical panel and contact

1. your installer or distributor,
2. your service center or
3. Stelpro’s customer service department.

In all cases, you must have a copy of the invoice and provide the information written on the product nameplate. Stelpro reserves the right to examine or to ask one of its representatives
to examine the product itself or any part of it before honoring the warranty. Stelpro reserves the right to replace the entire unit, refund its purchase price, or repair a defective part. Please note that repairs made within the warranty period must be authorized in advance in writing by Stelpro and carried out by persons authorized by Stelpro. Before returning a product to Stelpro, you must have a Stelpro authorization number (RMA). To obtain it, call the customer service department at 1-844-STELPRO. The authorization number must be written on the parcel or it will be refused.

CONDITIONS, EXCLUSIONS AND DISCLAIMER OF LIABILITY
This warranty is exclusive and instead of all other representations and warranties (except title), expressed or implied, and Stelpro expressly disclaims and excludes any implied warranty of merchantability or implied warranty of fitness for a particular purpose. Stelpro’s liability concerning products is limited as provided above. Stelpro shall not be subject to any other obligations or liabilities whatsoever, whether based on contract, tort, or other theories of law, concerning goods or services furnished by it, or any undertakings, acts, or omissions relating thereto. Without limiting the generality of the foregoing, Stelpro expressly disclaims any liability for property or personal injury damages, penalties, special or punitive damages, damages for lost profits, loss of use of equipment, cost of capital, cost of substitute products, facilities, or services, shutdowns, slowdowns, or for other types of economic loss or for claims of a dealer’s customers or any third party for such damages. Stelpro specifically disclaims all consequential,  incidental, and contingent damages whatsoever. This warranty does not cover any damages or failures resulting from:

•  faulty installation or improper storage;
• an abusive or abnormal use, lack of maintenance, improper maintenance (other than that prescribed by Stelpro), or a use other than that for which the unit was designed;
• a natural disaster or an event out of Stelpro’s control, including, but not limited to, hurricanes, tornadoes, earthquakes, terrorist attacks, wars, overvoltage, flooding, water damage, etc.

This warranty does not cover any accidental or intentional losses or damages, nor does it cover damages caused by negligence of the user or owner of the product. Moreover, it does not cover the cost of disconnection, transport, and installation. The warranty is limited to the repair or the replacement of the unit or the refund of its purchase price, at the discretion of Stelpro. Any parts replaced or repaired within the warranty period with the written authorization of Stelpro will be warranted for the remainder of the original warranty period. This warranty will be considered null and void and Stelpro will have the right to refuse any claims if products have been altered without the written authorization of Stelpro and if the nameplate numbers have been removed or modified. This warranty does not cover scratches, dents, corrosion, or discoloration caused by excessive heat, chemical cleaning products, and abrasive agents. It does not cover any damage that occurred during the shipping. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some of them do not allow limitations on how long an implied warranty lasts, so these exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may have other rights that vary from state to state or from province to province.

STELPRO DESIGN INC. Saint-Bruno-de-Montarville, Quebec, Canada, J3V 6L7

1-844-STELPRO WWW.UNIWATT.CA

References

• Uniwatt | Stelpro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>