VE017 Keyless Entry Door Lock

Product Information

Specifications

• Door Hole Size: 1-1/2″ or 2-1/8″ (38mm or 54mm)
• Door Edge Hole Size: 1″ (25mm)
• Backset: 2-3/8″ or 2-3/4″ (60mm or 70mm)
• Door Thickness: 1-3/8″ to 2″ (35mm to 50mm)

Product Usage Instructions

Step 1: Prepare the Door & Check Dimensions

Ensure the door dimensions match the specified sizes. Check for
obstructions in the door frame.

Step 2: Install the Latch & Strike

Extend the latch hole if needed. Test and adjust the latch bolt
to ensure proper function.

Step 3: Install Exterior Assembly

Measure the diameter of the door hole. Remove the spacer on the
exterior assembly and route the cable below the latch.

Step 4: Install Interior Assembly

Ensure the latch bolt is retracted before installation. Install
the mounting plate with screws.

FAQ

Q: How do I know if I need to extend the latch hole?

A: Temporarily install the latch bolt. If it is stuck, extend
the latch hole using a 1″ drill bit.

Q: What should I do if the latch bolt is not functioning

properly?

A: Remove the latch bolt and chisel out a small channel at the
top of the hole to allow proper rotation.

Q: How deep should the hole in the door frame be for the

strike?

A: The hole should be drilled a minimum of 1″ deep in the door
frame for proper installation of the strike.

Veise

Installation Manual

·wr:m~N

VE017)

Tutorial Video
Scan the QR code and search VE017 to get the video.

– +1 (855)400-3853 ……………~
Ill support@iveise.com S iveise.com

Content

· Parts List

01

· Installation Guide

02

Step 1: Prepare the Door & Check Dimensions

02

Step 2: Install the Latch & Strike

05

Step 3: Install Exterior Assembly

08

Step 4: Install Interior Assembly

10

· How to Reset

12

· Troubleshooting

13

Installation Overview

Parts List
0 Mechanical Key x2

(9 Latchx1

e Sb1kex1 ~

G Mounting Plate x1
~
G Mounting Plate
Screwsx2
,’·’*· +i

0 Exterior Assembly
Screw (Optional)
8 Interior Assembly
Screwsx3
a- a- a-
· Reset Tool x1
u

(9 Interior Assembly x1

~ Reinforcement ~O Plate x1

(Optional)

6f’

0 Strike Screws x2

(]0 ~ ~ f ) Latch Screws x2

Battery Cover x1

~ ~

4D Drive-In Collar
(Optional)

G) User Card x2

&Missing any parts? Call us at +1 (855)400-3853. iili support@iveise.com 01

~ Installation Guide

· Step 1: Prepare the Door & Check Dimensions

0
The hole in the door is 1-1/2″ or 2-1/8″ (38mm or 54mm).
The hole in the door edge is 1″ (25mm).

f)
The backset is either 2-3/8″ or 2-3/4″ (60mm or 70mm).

2-3/8″ or 2-3/4″ (60mm or 70mm) ‘

– —

The door thickness is 1-3/8″ to 2″ (35mm to 50mm).
‘
02

– -1-3/8″to2″
(35mmto
~ 50mm)

f ~91

J

Make sure the door frame

is aligned with the door.

There are no obstructions stuck in the door frame.

– ——-“1

~ Installation Guide
· Step 1: Prepare the Door & Check Dimensions

Optional: Instructions for doors with 1-1/2″ (38mm) holes

1. Test whether you need to extend the Latch hole.

Temporarily install the Latch bolt.

If the Latch bolt is stuck, you need to extend the Latch hole.

Fit properly Fit improperly

Extend the Latch hole at least 13/64″ (5mm) deep by using a 1″ (25.4mm) Drill Bit.
03

~ Installation Guide
· Step 1: Prepare the Door & Check Dimensions

2. Test the extended Latch hole. Temporarily install the Latch bolt, rotate it with a screwdriver to test if it extends and retracts properly.

If the Latch bolt is stuck, remove the Latch bolt and chisel out a small channel at the top of the hole to give the Cam room to rotate. (Refer to the following image)

04

~ Installation Guide
· Step 2: Install the Latch & Strike
0 Confirm the backset and adjust the Latch.
Hold the Latch in front of the door hole, flush the Latch against the door edge. Is the slot hole centred in the door hole?

YES
No need to adjust.

– – – EI –
Slot hole is NOT centred.

~ rnj
2~ .
(60mm)

Rotate and pull the Latch as shown to extend the

Latch.

05

~ Installation Guide
· Step 2: Install the Latch & Strike
f ) Install the Latch.

‘

– – – – -1–J_)

06

~ Installation Guide

· Step 2: Install the Latch & Strike

B Test if the Latch bolt extends and retracts properly by using a screwdriver.

,-

~

-,

I mlmportant:

I

I

I

I Before installation, the Latch bolt should be retracted !

! completely (in the unlocked position).

I

~ –

Lockel;~- X _’,-·/,)~

…..__…..

D Install Strike on the door frame.

& ‘ —————————————–‘

! Important:

!

i i I

l

Make sure the hole in door frame is

: drilled a minimum of 1″ (25mm) deep. :

‘~-1

~ Installation Guide
· Step 3: Install Exterior Assembly
0 Measure the diameter of the hole in the door.

…. .. 1-1/2″ or 2-1/8″
(38mm or 54mm)

2-1/8″ {54mm)
Go to next step directly.
1-1/2” (38mm)
Remove the spacer on the exterior assembly.

08

~ Installation Guide
· Step 3: Install Exterior Assembly

f ) Route the cable below the Latch and
insert the Torque Blade through the slot in the Latch.
Do not put the Mechanical Key in the cylinder during the installation.

Install the Mounting Plate with the Mounting Plate Screws.
Do not overtighten screws.

~-ET

m

~ –

Mounting Plate Screws(K)
09

~ Installation Guide

· Step 4: Instal/Interior Assembly

0 Disassemble the Battery Cover.

fJ Insert the cable connector to the socket. Push the connector in firmly until it is completely attached.

–&—

—— —— —–Important:

——

——-

‘ l

! I
Do not load batteries until the lock

is completely installed.

J

10

~ Installation Guide

· Step 4: Instal/Interior Assembly

B Attach Interior Assembly to Mounting

Plate and tighten 3 screws.

l ~Jft

l

Be sure not to use the wrong screws, or it

may lead to short-circuit and other problems.

D Insert 4 M Alkaline batteries and put on the Battery Cover.

11

e How to Reset

,~ . ·————————————————————————————-…

0 Keep the door open and unlocked.
f ) Remove one battery, press and hold the

Scan the QR code
—-.:: Search VE017

Reset Button for 5 seconds by using the

Call us at +1 (855)400-3853,

Reset Tool.

if you have any questions.

S i\1 support@iveise.com iveise.com

Keep holding the Reset Button and put the ·-~/

battery back, until you hear a long sound of

beep and the Latch bolt extends out auto-

matically.

Settings Master Code
Auto Lock Silent Mode Wrong Entry Limit Shutdown Time Vacation Mode 12

Factory Default 12345678 Disabled Disabled 10 times 3 mins Disabled

CD Troubleshooting
…, The Latch bolt keeps going in and out.
Disassemble and reinstall the lock by following the installation tips. 1. Please don’t insert the Mechanical Key in lock cylinder before or during installation. 2. Keep the Latch fully retracted and the Torque Blade horizontal. 3. Please make sure to route the cable below the Latch. 4. The Exterior and Interior Assembly should be installed parallel to the door edge.
… I cannot remove my key unless it is in the locked position.
Uninstall the Interior and Exterior Assemblies. Before re-installation, please follow these guidelines: 1. Make sure the Latch bolt is in the retracted position. 2. Do not insert the Mechanical Key in lock cylinder before or during installation. 3. Make sure the Torque Blade is inserted horizontally.
… Fail to reset.
1. The battery is low if the battery indicator light keeps flashing. Please replace it with 4 new batteries. (Alkaline batteries only) 2. Please refer to “How to Reset” section and perform a resetting again.
13

CD Troubleshooting
…, How to lock manually on the Keypad from outside?
0 1. Touch once.
2. Press and hold any button for 2 seconds. 3. Use your Fingerprint.
…, The Latch bolt won’t be extended out completely after installation.
Please review if the Exterior Assembly is aligned with the door parallelly. The Exterior Assembly should not be at a crooked angle.
If you have any questions, please contact us at +1 (855)400-3853.
ill support@iveise.com
14

FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radiofTV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
15

IC Warning
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet appareil est conforme aux CNR exemptes de licence d’lndustrie Canada . Son fonctionnement est soumis aux deux conditions suivantes : ( 1 ) Ce dispositif ne peut causer d’interferences ; et ( 2 ) Ce dispositif doit accepter toute interference , y compris les interferences qui peuvent causer un mauvais fonctionnement de l’appareil. Ce materiel est complete par une exposition de rayonnements IC pour un environnement naturel. Ce materiel doit etre installe et se faire avec une distance minimale de 20cm entre les radiateurs et les autresYour body shop.
16

Information & Safety Warnings
· Protect your User Codes and Master Code. · Restrict access to your lock’s Interior Assembly and routinely check your settings to ensure they have not been altered without your knowledge. · Do not use an electric screwdriver during installation. · This manufacturer advises that no lock can provide complete security by itself. · This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. · No lock can substitute for caution, awareness of your environment, and common sense. · Take care to ensure a long-lasting finish. Please use soft and damp cloth to clean the lockset if you need. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing. · The lock is water-resistant. It can withstand water splashes; however, do not let water and liquids get into the lock. · Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.
17

Need Help? Contact Us!
If you have any questions, please contact us at
() +1 (855)400-3853
(Monday-Friday 9:00am-5:00pm PST)
llsupport@iveise.com Siveise.com

References

• VEISE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>