Veise KS02D Keypad Digital Deadbolt User Manual

June 11, 2024
Veise

KS02D Keypad Digital Deadbolt
User ManualVeise KS02D Keypad Digital Deadbolt

KS02D Keypad Digital Deadbolt

** Before Installing the Lock, Please Check Door Jamb and Door Preparation.Veise KS02D Keypad Digital Deadbolt - Door
Jamb Installation Instructions of Keypad Digital Deadbolt TOOL REQUIRED : Do not use an electric screwdriver during installation.
IMPORTANT:** Do not load batteries until lock is completely installed.
Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade. Veise KS02D
Keypad Digital Deadbolt - fig

Parts List

Veise KS02D Keypad Digital Deadbolt - Parts List Prepare the door and check dimensions
A. Measure to confirm that the hole in the door is 2-1/8″ (54mm). Measure to confirm that the hole in the door edge is 1″ (25mm). B. Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70mm) C. Measure to confirm that the door is 1-3/8″ to 2″ (35 mm or 50mm) thick. D. Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep.

Install the latch and strike

A. Determine backset and adjust the latch Hold the latch in front of the door hole, with the latch face flush against the door edge. Is the slotted hole centered in the door hole? YES No adjustment is required. Proceed to next step. NO
Slotted hole is NOT centered.
Rotate and pull the latch as shown to extend latch.Veise KS02D Keypad
Digital Deadbolt - extend latchB. Install the latchVeise KS02D Keypad Digital Deadbolt - Install
the latchC. Use a screwdriver to test if deadbolt works smoothly.Veise KS02D Keypad Digital Deadbolt - Install the
latchD Install strike on the door frame.
IMPORTANT:
Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep.
Veise KS02D Keypad Digital Deadbolt - Install the
latch

Install exterior assembly

IMPORTANT:
Before installation, make sure the latch is fully retracted (in the unlocked position) Veise KS02D Keypad Digital Deadbolt - Install the
latchVeise KS02D Keypad Digital Deadbolt -
TorqueA. With the latch fully retracted (in the unlocked position), route the cable below the latch, and insert the torque blade through the slot in the latch.Veise KS02D Keypad Digital Deadbolt -Keep
parallelB. Secure the mounting plate with the supplied screws. Do not overtighten screws.
Install interior assembly
A. Push the battery cover out in the direction as illustrated.
IMPORTANT:
Do not load batteries until lock is completely installed. B. Insert the cable connector to the socket. Push the connector in firmly until it is completely attached. C. Keep the thumb turn in vertical position and install the interior assembly. Veise KS02D Keypad Digital Deadbolt-
UnlockedD. Attach Interior Assembly to Mounting Plate and tighten 3 Screws.Veise KS02D Keypad Digital Deadbolt - Attach
Interior

Detect left/right hand door installation

Reset the lock to teach the lock the orientation of the door.
IMPORTANT: This step is required and crucial for the lock to operate properly.
A. While the door is OPEN and UNLOCKED, load 3 AA batteries into the battery compartment.
Note: For long last, please use all new, non-rechargeable Alkaline batteries only. B. Press and hold the Reset button on the interior assembly by using the reset tool. C. Load the 4th battery and keep holding the reset button for 3 seconds, until you hear the sound of “beep”. The latch bolt will extend to learn the orientation of the door automatically.Veise KS02D Keypad
Digital Deadbolt- door automaticallyInstallation Instructions of Handle set

TOOL REQUIRED:
Do not use an electric screwdriver during installation. Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.Veise KS02D Keypad Digital
Deadbolt - partsA. Handle set x1
B. Latch x1
C. Strike x1
D. Dust Cover x1 (optional)
E. Handle Lever x1
F. Handle Lever & Handle set screws x3
G. Latch Strike screws x4
H. SpacerVeise KS02D Keypad Digital Deadbolt - Prepare the
door Prepare the door and check dimensions
If your door already has the holes shown in the picture below, proceed to the next step, if your door does not have holes, use the mounting template to drill a new hole.
Latch backset adjustment
Backset is the distance from the door edge to the center of the hole in the door.
The latch is provided with adjustable design which can fit either 2-3/8’’(60mm) or 2-3/4’’(70mm) backset.
A. If the backset of your door is 2-3/8″(60mm), no need to adjust the latch. B. If the backset of your door is 2-3/4″(70mm), please adjust the latch.Veise KS02D Keypad Digital Deadbolt - Latch backset
adjustment

Install latch and strike

Veise KS02D Keypad Digital Deadbolt - latch and strike IMPORTANT:
The latch should be aligned with the chiseled properly.
IMPORTANT:
Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep.

Install Handleset

Veise KS02D Keypad Digital Deadbolt - Install
Handleset Install Handle LeverVeise KS02D
Keypad Digital Deadbolt - Handle Lever Test the Handleset after installation.
Keep the door open, retract the latch by pressing knob from outside and pushing the lever from inside of the door to test if the Handle set works smoothly.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals