Veise VE06-H Smart Lock User Guide
- June 7, 2024
- Veise
Table of Contents
- Veise VE06-H Smart Lock
- Installation Instruction
- Exterior Assembly
- Interior Assembly
- How to Lock/ Unlock
- Definitions
- INSTALLATION INSTRUCTION
- Parts List
- Factory Default Settings
- Programming Guide
- Troubleshooting
- FCC Statement
- Information & Safety Warnings
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Veise VE06-H Smart Lock
Installation Instruction
Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.
IMPORTANT:
The DDLock App is required to operate the lock. After the lock is properly
installed, the first one who register and pair the lock will be the
administrator.
USER GUIDE
At a Glance
Exterior Assembly
Interior Assembly
How to Lock/ Unlock
UNLOCK the door from outside
LOCK the door from outside
UNLOCK the door from inside
Rotate the thumb turn to Unlock position.
LOCK the door from inside
Auto Lock Mode
In Auto Lock mode, the device will be locked automatically.
Manual Mode
Rotate the thumb turn to Lock Position.
Definitions
-
Master Code
The default master code is 123456.
Before pairing your lock in DDLock App, please do not change the default master code.
After pairing successfully, the master code will be changed to a random 7 digit number, and you can change it to your own master code in the App(Settings>Basics>Admin password). -
Auto Lock & One-touch Lock
Automatically locks the deadbolt after the door closed in 5 seconds. Auto Lock is disabled by default. The Auto Lock time can be customized between 1 and 900 seconds.
One-touch Lock is pressing and holding “#” on the touch keypad for 2 seconds to lock from outside. -
Private Mode
Press and hold “Privacy button” on the inside panel for more than 2 seconds to enable Private Mode.
Press “Privacy button” once to disable Private Mode.
In Private Mode, it’s unable to unlock by Password and IC cards. Bluetooth, Physical Key and Admin password unlocking are available. -
Wrong Entry Limit
After 5 times unsuccessful attempts at entering an invalid password, the device will shut down for 2 minutes. -
Passage Mode
Enable Passage Mode, the lock will stay Unlocked until it’s locked manually.
In Passage Mode, Auto-lock will be disabled. -
Anti-peeping password
Entering random numbers before or after correct password will also unlock the door, which can prevent the password being exposed.The length of anti-peeping password should be within 16 digits.
INSTALLATION INSTRUCTION
Parts List
If any parts are lost or damaged, please contact Customer Support.
-
Prepare the door and check dimensions
-
install the latch and strike
-
Use a screwdriver to test if deadbolt works smoothly.
-
Install strike on the door frame.
-
-
Install exterior assembly
-
Install interior assembly
Factory Default Settings
How to Reset?
Press and hold the Reset button on the interior assembly for 5 seconds by
using the Reset tool, until you hear a short beep and Green light flashes
once.
IMPORTANT: If the lock is paired successfully, please locate the lock, go to setting in DDLock App, turn on the Reset Button before resetting.
Programming Guide
IMPORTANT:
The default master code is 123456. Before programming in the lock, it’s
required that you change the default master code to a new master code of your
own. If you have changed the default master code by following the Programming
Guide, you must reset the lock before pairing this lock to DDlock App.
Troubleshooting
-
Why the tock won’t accept any inputs after I entered a code incorrectly for so many times?
The lock will shut down for 2 minutes after 5 unsuccessful attempts at entering an invalid code.
You can unlock the lock once in the App or wait 2 minutes to continue.
How do I lock manually from outside?
Press and hold # to lock the lock from outside.
The batteries are completely dead before I replace new batteries.
When the batteries are completely dead, the physical keys are available to unlock. -
Why the thumb turn won’t turn to lock/unlock?
The door direction might be set wrong during the installation, please follow the Installation guide or video to re-install the lock. -
Why does the latch won’t turn out completely after installation?
Please review if the exterior assembly is aligned with the door parallelly. The exterior assembly should not be at a crooked angle.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against hanmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES – 3 (B)/NMB – 3(B).
- This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
- This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
- This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Information & Safety Warnings
-
Protect your User Codes and Master Code.
-
Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
-
Do not use an electric screwdriver during installation.
This manufacturer advises that no lock can provide complete security by itself. -
This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.
-
No lock can substitute for caution, awareness of your environment, and common sense.
-
Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
-
The lock is water resistant. It can withstand water splashes; however, do not let water and liquids get into the lock.
-
Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.