Veise ZS01 Keyboard Digital Deadbolt Installation Guide

June 11, 2024
Veise

Veise ZS01 Keyboard Digital Deadbolt Installation Guide
Veise ZS01 Keyboard Digital Deadbolt

Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.

Installation Overview

Read this manual carefully before installing and operating!

STEP 1: Prepare the door and check dimensions
STEP 2: Install the latch and strike
STEP 3: Install exterior assembly
STEP 4: Install interior assembly
STEP 5: Detect left/right hand door installation

Programming Instructions

P9: At a Glance
P10: How to Use
P 1 1: Definitions
P12: Code Format
P13: Quick Set Up
P 15: Factory Default Settings
P16 : Troubleshooting

TOOL REQUIRED
Do not use an electric screwdriver during installation

IMPORTANT
Do not load batteries until lock is completely installed

Instructions Overawe

Instructions Overawe

Parts List

  • Backup Key x2

  • Exterior Assembly x1

  • Latch x1

  • Strike x1

  • Reinforcement ” Plate x1 (optional)

  • Mounting Plate x1

  • Interior Assembly x1

  • Battery Cover x1

  • Strike Screws x2

  • Latch Screws x2

  • Mounting plate Screws x2

  • Interior Assembly Screws x3

  • Reset Tool x1

  • Drive-in Collar (Optional)

Prepare the door and check dimensions

Measure to confirm that the hole in the door is 2-1/8″ (54mm).

Measure to confirm that the hole in the door edge is 1″ (25mm).
Check Dimensions

Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70mm)
Check Dimensions

Measure to confirm that the door is 1-3/8″ to 2″ (35 mm or 50mm) thick.
Check Dimensions

Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep.

Check Dimensions

Install the latch and strike

Determine backset and adjust the latch

Hold the latch in front of the door hole, with the latch face flush against the door edge. Is the slotted hole centered in the door hole?
Installations Latch

YES
No adjustment is required. Proceed to next step.

NO
Sloshed hole is NOT centered.

Rotate and pull the latch as shown to extend latch.

Product Dimensions

Installations the Latch

Installations the Latch



Use a screwdriver to test if deadbolt works smoothly.

Install strike on the door frame

IMPORTANT:
Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep.
Installations Strike

Install exterior assembly

IMPORTANT:
Before installation, make sure the latch is fully retracted (in the unlocked position)
Before Installation

With the latch fully retracted (in the unlocked position), route the cable below the latch, and insert the torque blade through the slot in the latch. latch.
Installations Exterior Assembly

Secure the mounting plate with the supplied screws. Do not overtighten screws.
Installations Exterior Assembly

Push the battery cover out in the direction as illustrated.

IMPORTANT:
Do not load batteries until lock is completely installed.
Installations Exterior Assembly

Insert the cable connector to the socket. Push the connector in firmly until it is completely attached.

Keep the thumb turn in vertical position and install the interior assembly.
Installations Exterior Assembly

Attach Interior Assembly to Mounting Plate and tighten 3 Screws.

Detect IefUright hand door installation

Reset the lock to teach the lock the orientation of the door.

IMPORTANT:
This step is required and crucial for the lock to operate properly.

While the door is OPEN and UNLOCKED, load 3 AA batteries into the battery compartment.

Note:
For long last, please use all new, non-rechargeable Alkaline batteries only.
Door Installation

Press and hold the Reset button on the interior assembly by using the reset tool.

Load the 4th battery and keep holding the reset button for 3 seconds, until you hear the sound of “beep”. The latch bolt will extend to learn the orientation of the door automatically
Door Installation

Programming Instructions

At a Glance

Exterior Assembly
Exterior Assembly

Interior Assembly
Interior Assembly

How to Use

UNLOCK the door from outside
How to Use

LOCK the door from outside

Auto Lock Mode
In Auto Lock mode, the bolt will extend out automatically in 30 seconds after unlocking.

Manual Mode
Press any key on keypad for 2 seconds.

UNLOCK the door from inside

Rotate the thumb turn to Unlock position.

LOCK the door from inside

Aufo Lock Mode
In Auto Lock mode, the device will be locked automatically.

Manuat Mode
Rotate the thumb turn to Lock Position.
Lock Position

Definitions

  • Master Code
    Required for programming and feature settings. Master code can be used to unlock the door under vacation mode. The default master code needs to be changed before programming. Property owner & manager should keep this information confidential.

  • Auto Lock
    Automatically locks the deadbolt 30 seconds after unlocking. This feature is off by default. You can customize the Auto Lock time delay between 10 and 99 seconds. • Key Unlock Key Unlock is always available when the batteries are completely dead or valid User Codes are forgotten.

  • Low Battery
    Indicator If you hear 10 beeps along with 10 red light flashing after pressing any key to lock or unlock the door, that’s an alert for replacing batteries. Please replace with 4 brand new AA alkaline batteries and do not mix used and new batteries. All settings are stored in the lock while the batteries are removed and replaced.

  • Wrong Entry Limit
    After 10 unsuccessful attempts at entering a invalid PIN code, the unit will shut down for 3 minutes.

  • Silent Mode
    The beep sounds when pressing keypad can be muted. But you will still hear low battery and system alerts.

  • Vacation Mode
    This is a security feature for you when you are leaving your home for vacation or long trip. Enabling vacation mode will restrict all user codes until master code is entered on keypad. If the lock would be unlocked by the thumb turn from the inside, the lock will sound an alarm.

  • One 7ime
    User Code This code only can be used once and will be automatically deleted after used.

  • Unlock with
    Fake code User can prevent pin code exposure from strangers by entering random digits before or after pin code.
    Definitions

Code Format

  1. Master Code(4 to 10 digits): The default Master Code is 12 45678. It is required that you change it to a code of your own before programming.
  2. User Code: 20 User Codes (4-10 digits), 1 one-time User Code can be programmed and stored in the lock.
  3. Both Master Code and User Code don’t support the following combination of numbers

A. Forward number sequence.
B. Backward number sequence .
C. Repeat number sequence.
D. Contain existing code sequence.
Code Format

Quick Set Up

IMPORTANT:
The default Master Code is 12/4567% . It is required that you change it to a code of  your own before programming
Setting Step
Setting Step
Setting Step
Setting Step
Notes:

  1. Beeps only sound when the Silent Mode is disabled.
  2. If the indicators flash red light, it means your setting failed and it will require to re-enter master mode if you would like to continue your programming

Factory Default Settings

How to Reset†

IMPORTANT:
The resetting will delete all User Codes stored in the lock.

Step 1. Keep the door open and unlocked.
Step 2. Press and hold the Reset button, at the same time take out one battery and then place it back.
Step 3. Keep holding the Reset button for 3 seconds, until you hear the sound of “beep” and the latch will extend automatically

Settings Factory Defaut
Master Code 12345678
Auto Lock Disabled
Silent Mode Disabled
Wronp Code Entry Limit 10 times
Shutdown Time 3 mins
Vacation Mode Disabled

Troubleshooting

Why does not the latch extend but the motor is rotating when resetting my lock2

Improper installation may have caused the issue. Please follow the steps to review:

  1. Please make sure the latch and strike are aligned.
  2. Please slightly loosen the mounting screws on the external assembly keypad and the latch bolt if the screws are over-tight- ened.
  3. Please open your door and reset the lock

1/1f hy’ does not the latch extend and the motor isn’t rotating when resetting my leak7
The deadbolt latch should be retracted(unlocked) through all your installation process.
The thumb turn should be vertical in your installation steps 4C and SA.

Please open your door and reset the lock.

When I attempt to lock/unlock my dead6olt, why does the latch go in and out for a few times?

It happens when the latch and strike are misaligned.

Please make sure the bolt hole on the door frame is at least 1 inch deep, so that the bolt can be fully extended.

Please check if the door can be closed properly, the deadbolt should not impact the strike or door frame on the door frame side, it should go directly into the hole properly

Why does my lock on/y work property when fhe backup Aey is in? Why am I unable to pull the key out in the unlocked position?

You may need to re-install the whole lock. Please make sure when you start to install, the lock is in unlocked status; Please make sure the thumb turn is vertical. Please do not put the backup key in the lock during the installation.

What does 5 short and fast beeps mean while program- m/ng?
It alerts you either time-out or wrong entry. Please be sure to complete each setting step within 5 seconds. Please change the default master code in the first time programming. Please be sure the user code is with correct format and with 4 to 10 digits.

What if I forget my faster Cokes
If you forget your Master code, resetting your lock, then the original master code (12345678) works, and all previous user codes were erased.

Information & Safety Warnings

  • Protect your User Codes and Master Code. • Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
  • Do not use an electric screwdriver during installation.
  • This manufacturer advises that no lock can provide complete security by itself.
  • This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.
  • No lock can substitute for caution, awareness of your environment, and common sense.
  • Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
  • The lock is water resistant. It can withstand water splashes; however, do not let water and liquids get into the lock.
  • Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals