SmallRig 4295 Wireless Follow Focus Kit Instruction Manual
- September 19, 2024
- SmallRig
Table of Contents
Operating instruction
Wireless Follow Focus Kit (Lite)
Thank you for purchasing Small Rig’s product.
Kits and Accessories
- Wireless Handwheel Controller
- Snap-on Follow Focus Gear Ring
- Wireless Rece ver Motor
- Rod Clamp with NATO Rail
- Allen Wrench
- <P15mm Rod
- USB-C to USB-C Cable
Instructions for Product Functions
Instructions for Product installation and Power
Supply Control
Instructions for installation of Wireless Receiver Motor
Instructions for Power Supply to Wireless Receiver Motor.
2.1 The wireless recover motor s powered by the included USB-C cable.
2.2 The wireless receiver motor s compatible with PD+ QC protocols, prov ding
high torque output; and the input voltage ranges from 5 V to 18 V.
Instructions for Wireless Handwheel Controller.
The input voltage of wireless handwheel controller ranges from 5 V to 12 V; an external power adapter supplies power to the wireless handwheel controller via the included USB-C cable.
Instructions for Product Operation Steps
Ensure that the ndicator of the wireless receiver motor s consistent with that of the wireless handwheel controller to guarantee the control; Double-click ® the button to cycle through the frequency bands, F00-01 – Fl 5-01.
[Note] The light color information corresponds to the frequency bands of
the MagicFlZ wireless receiver motor and wireless handwheel controller.
Automatic Lens Travel Calibration
Long press the CAL button for 2 seconds to start automations travel
caibration.
Manual Lens Travel Calibration
Long press the CAL button for 2 seconds to start automatic lens travel
calibration; single-click the CAL button to switch to manual travel
calibration.
Single-click the A I B mark (A-B-cancel) to mark the point.
Operation to Address Abnormality of Wireless Hand wheel Controller
The red ight fashing indicates the alarm of ow battery level or wire ess
receiver
Description of Abnormal Alarm Case for Wireless Receiver Motor.
- The lens damp ng s too high. and the motor s stuck by a fore gn object.
- The motor input voltage s too low.
Operation to Address Abnormality of Wireless Receiver Motor.
- Increase the input voltage or connect a device that supports PD+OC for power supply;
- Use the included USB-C power cable or a USB3.0 power cable;
- Single-click the CAL button on the wireless receiver motor or any button on the wireless handwheel controller to recalibrate the lens travel.
Operation to Address Abnormal Forward I Reverse Rotation of Wireless Receiver Motor.
The wireless receiver motor shows abnormal reverse rotation
- Turn to the end position as shown n the Figure.
- Long press the button@ for 5 seconds until the current status light stops flashing to complete the reset operation.
Specifications
Wireless Handwheel Controller
Battery Capacity Parameters Input
3.7V 1400mAh 5.18Wh 5V-12V
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, f
not nstalled and used n accordance with the instructions, may cause harmful
interference to radio communications. However, there s no guarantee that
interference will not occur n a particular installation. f this equipment does
cause harmful interference to radio or tele sion reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the follow ng measures
-Rear ent or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment nto an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party.
Responsible for compliance could void the user’s authority to operate this
equipment.
(Example- use only shielded interface cables when connecting to computer or
peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation s subject to
the following two conditions
(1) This dev ce may not cause harmful interference, and (2) This dev ce must
accept any interference received, including interference that may cause
undesired operation.
RF warning statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used n portable exposure condition without restriction.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s).Operation s subject to the following two conditions
- This dev ce may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
LQ-P1269-18 Manufacturer: Shenzhen Leqi Innovation Co., Ltd.
Add: Rooms 103, 501 and 601, Building 5, Fenghe Industrial Park, Nos. 1301-50
Guanguang Road, Longhua District, Shenzhen, Guangdong, China.
103, 501, 601 Consignor: Shenzhen LC Co., Ltd. Add: Rooms 602, Building 5,
Fenghe Industrial Park, No. 1301-50 Guanguang Road, Xinlan Community, Guanlan
Street, Longhua District, Shenzhen, Guangdong, China.
219-249218
219-249145
FCC ID: 2BC2U-4297
IC: 31675-4297 1171
FCC ID: 2BC2U-4295
IC: 31675-4295 4943.1-2022
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>