C01 Baby Monitoring Camera

“`html

Product Information

Specifications

• Model: Harbor C01

• FCC ID: 2BFBC-C01

• IC: 32246-C01

• Compliance: Part 15 of FCC rules and Industry Canada
  license-exempt RSS standards

• Manufacturer: Project Monitor, Inc. dba Harbor

• Address: 4516 Lovers Lane 392, Dallas, TX 75225

• Phone Number: 214-919-3432

Product Usage Instructions

Installation

1. Ensure the antenna supplied by Harbor is used with the
   device.

2. Keep a minimum distance of 20 cm between the device and your
   body during operation.

3. Install the antennas to provide a separation distance of at
   least 20 cm from all persons.

Operation

Follow these steps to operate the Harbor Camera:

1. Power on the device by pressing the power button.
2. Adjust settings using the control panel or app as needed.
3. To capture images or videos, press the capture button.
4. Review and transfer your media to a computer or storage
   device.

FAQ

Q: What should I do if I encounter interference during camera

operation?

A: If interference occurs, ensure that the antenna is properly
connected and positioned according to the guidelines provided in
the manual. You may also try changing the location of the device to
reduce interference.

Q: How do I update the firmware of the Harbor Camera?

A: To update the firmware, visit our website at harbor.co/start
and follow the instructions provided in the support section for
firmware updates.

“`

Harbor Camera User Manual
For more information and support, please visit our website:
harbor.co/start
HPN-300-0009

FCC and IC Notices
FCC and IC Notices
This equipment complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standards. This equipment should only be used with the antenna supplied by Harbor. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Harbor C01 is contains the following IDs: FCC ID: 2BFBC-C01 IC: 32246-C01
The device complies with Part 15 of the FCC rules and Industry Canada license- exempt RSS standards subject to the following two conditions:
1. The device may not cause harmful interference. 2. The device must accept all interference received, including interference that may cause undesired operation.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Avertissements de la FCC et IC
Cet appareil est conforme à la Partie 15 des règlements de la FCC et Industrie Canada exempts de licence standard RSS. Cet appareil doit être utilisé uniquement avec l’antenne fournie par Harbor Inc. Tout changement ou modification non expressément approuvée par le fabricant pourrait annuler l’autorité de l’utilisateur de faire fonctionner l’appareil
Harbor C01 se contient les identifiants suivants: FCC ID: 2BFBC-C01 IC: 32246-C01
Cet appareil est conforme à la Partie 15 des règlements de la FCC et Industrie Canada exempts de licence standard RSS soumis aux deux conditions suivantes:
1. Cet appareil ne peut causer des interférences nuisibles. 2. Cet appareil doit accepter toutes les interférences reçues, y compris les interférences qui peuvent perturber le
fonctionnement.
Conformément à la réglementation d’Industrie Canada, cet émetteur radio ne peut fonctionner à l’aide d’une antenne d’un type et maximum (ou moins) Gain approuvé pour l’émetteur par Industrie Canada. Pour réduire le risque d’interférence avec d’autres utilisateurs, le type d’antenne et son gain doivent être choisis afin que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.
HPN-300-0009

Supplier’s Declaration of Conformity
Per FCC CRF 47 Part 2 Section 2.1077(a) Name: Project Monitor, Inc. dba Harbor Address: 4516 Lovers Lane 392, Dallas, TX 75225 Phone Number: 214-919-3432 Hereby declares that the products M01 and C01 conform to the following regulations: FCC Part 15, Subpart B, section 15.107(a), 15.107(d), and section 15.09(a)
HPN-300-0009

Revision History

Revision REV-01
–

Comment Initial release –

Date 2024-04-13
–

Author S.G. McBeath
–

HPN-300-0009

References

• Start | Harbor

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>