LYNX TS-2500 Series Pro Audio Introduces User Manual

: September 17, 2024
: LYNX

Table of Contents

LYNX TS-2500 Series Pro Audio Introduces
Product Usage Instructions
FAQ
IMPORTANT SAFETY INSTRUCTIONS
INTRODUCTION
TS characteristics
TS Dimensions (in mm)
TECHNICAL SPECIFICATIONS
TROUBLESHOOTING
LYNX PRO AUDIO GUARANTEE
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LYNX TS-2500 Series Pro Audio Introduces

Product Usage Instructions

Safety Instructions

The TS amplifier is verified and tested to meet European Norms and International Norms regarding Electromagnetic Compatibility and Electrical Safety. Make sure to adhere to the following safety directives:

Radiated Emissions: EN55013-1 (1996)
RF Immunity: EN55103-2 (1996)
Electrical Safety: EN60065 (1993), IEC65 (1985) and amendments 1, 2, and 3
Low Voltage Directive: 73/23/EEC
EMC Directive: 89/336/EEC

CAUTION: RISK OF ELECTRIC SHOCK Do not open the amplifier. Avoid exposing it to humidity and dust. Only use power cords in good condition to prevent electrical shock.

Unpacking the TS Amplifier

Before unpacking the amplifier, ensure that the box is undamaged. If there is any damage, report it to your provider. After unpacking and verifying its operation, keep the original box for potential future shipping needs.

Front Panel Description

CHANNEL: LEDs for clip, fault, and signal status.
POWER SUPPLY INDICATION: LED shows power status.
POWER ON SWITCH

Back Panel Description

Include the back panel description here.

FAQ

Q: What should I do if the amplifier shows a fault indication?
A: If the amplifier displays a fault indication, immediately turn it off and disconnect from power. Refer to the user manual for troubleshooting steps or contact Lynx Pro Audio S.L. for assistance.
Q: Can I use the amplifier outdoors?
A : It is not recommended to expose the amplifier to humidity or dust, so outdoor usage is not advised.

WELCOME

Just contact the new generation of digital amplifiers, designed and manufactured by Lynx Pro Audio S.L.
Before working with the amplifier we recommend that you read this manual, in its pages, you will find instructions for use, programming examples and practical advice that will be of great help.
For the maximum optimization of any sound system, a first-class digital processor with different processing options is required. This TS amplifier become a working tool of great value, providing the user with the best solutions in the market with the highest level of accuracy and a host of features for the professional.
We hope that as a user you will be completely satisfied. We are sure that the TS amplifier will meet your expectations and make it easier for you to get the most out of your system.

IMPORTANT SAFETY INSTRUCTIONS

The CE mark of the TS amplifier shows that it is verified and tested to accomplish the European Norms and International Norms about Electromagnetic Compatibility and Electrical Safety.

Radiated Emissions: EN55013-1 (1996)
RF Immunity: EN55103-2 (1996)
Electrical Safety: EN60065 (1993) IEC65 (1985) and emendation 1, 2 and 3

This product also meets the specifications of the following safety directives:

Low Voltage Directive 73/23/EEC
EMC Directive 89/336/EEC

Product Developed and Manufactured in the European Union

CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN

Warning :

Do not expose the processor to humidity and dust.
Do not take off the top cover.
Do not handle internal elements to avoid electrical shock.
Use only power cords in good condition

Unpacking the TS

Before unpacking your new amplifier, verify that the box does not show any damage or deformation. If this happens, please claim the damage to your forwarder. Once unpacked and verified its correct operation, keep the original box in case you need to ship it back to your provider.

INTRODUCTION

The TS series comprises high-performance 4-channel amplifiers of medium/high power, specifically designed for the installation market.
These amplifiers can connect to both high and low-impedance loads via their Phoenix input and output connectors and allow output levels to be controlled through the rear panel potentiometers.
The design includes Lynx Pro Audio’s advanced Power Control Management system, which allocates power across the channels according to the user’s needs, even enabling maximum power to be delivered through a single channel.
These amplifiers offer extensive configuration options, including Bridge mode, subsonic filter, per-channel power limiter, and signal link, to meet the demands of any installation.
They can also be equipped with a GPIO connection for integration with third-party control systems. Additionally, DanteTM Networking (AES67) inputs are available for the TS amplifiers.With all these configurations, the TS amplifiers can meet the requirements of any installation ranging from 300 to 2500 W.

TS frontal panel description

CHANNEL
These LEDs are used to provide visual information about the status of the clip, faults and signals.
POWER SUPPLY INDICATION
The LED indicates that the amplifier is receiving power and is switched on.
POWER ON SWITCH
TS back panel description
GAIN SELECTION
Gain configuration from 26 to 40 dB.
GPI CONTROL
GPI Power: On/off by maintained contact or voltage.
GPI Mute: Mute/unmute completelly amplifier by contact or voltage.
CHANNEL SETUP
50Hz HP: 50Hz subsonic filter.
GPO MONITOR
GPIO for third party interface. AES67 and Dante options.
GPO STATUS
Monitor each individual channel, with switching contacts for fault/ OK status.
SPEAKER OUTPUTS
Up to 10000 W in 4 channels.
OUTPUT MODE
Output Mode: Hi impedance voltage selector. Low impedance power limitation.
Bridge mode: Low impedance bridge mode. 200V/140V high impedance mode.
SIGNAL INPUTS
Input Link: Linking of input signals in consecutive channels.
Output Levels: Hidden potentiometers on the rear for adjusting output levels.

TS characteristics

Low weight high efficiency class D topology.
Universal power supply with PFC.
Up to 10000 W in 4 channels.
8, 4 and 2 Ohm low impedance operation.
100, 70, 50 and 35 V high impedance modes.
Power Control Management.
Phoenix connectors for inputs and outputs.
Up-side-down design to avoid fan dust accumulation.
Low weight high efficiency class D topology.
Universal power supply with PFC.
Up to 10000 W in 4 channels.
8, 4 and 2 Ohm low impedance operation.
100, 70, 50 and 35 V high impedance modes.
Power Control Management.
Phoenix connectors for inputs and outputs.
Up-side-down design to avoid fan dust accumulation.

TS Output power

| TS-2500| TS-5000| TS-10000
---|---|---|---
2 ohms| 4 x 312 W| 4 x 1250 W| 4 x 2500 W
4 ohms| 4 x 625 W| 4 x 1250 W| 4 x 2500 W
8 ohms| 4 x 625 W| 4 x 1250 W| 4 x 2500 W
Hi -Z 100 V| 4 x 625 W

1 x 1250 W

| 4 x 1250 W

1 x 2500 W

| 4 x 2500 W

1 x 2500W

Hi -Z 70 V| 4 x 625 W

1 x 900 W

| 4 x 1250 W

1 x 1800 W

| 4 x 2500 W

1 x 2500 W

TS Dimensions (in mm)

TECHNICAL SPECIFICATIONS

| TS-2500| TS-5000| TS-10000
---|---|---|---
Number of channels| 4| 4| 4
Total output power| 2500 W| 5000 W| 10000 W

Output power

| ****

4 x 312 / 1 x 312 W

| ****

4 x 1250 / 1 x 1250 W

| ****

4 x 2500 / 1 x 2500 W

@ 2 Ohms| 4 x 430 / 1 x 430 W| 4 x 1250 / 1 x 1700 W| 4 x 2500 / 1 x 3330 W
@ 2.67 Ohms| 4 x 625 / 1 x 625 W| 4 x 1250 / 1 x 2500 W| 4 x 2500 / 1 x 2500 W
@ 4 Ohms| 4 x 625 / 1 x 1250 W| 4 x 1250 / 1 x 1250 W| 4 x 1250 / 1 x 1300 W
@ 8 Ohms| 2 x 625 W| 2 x 5000 W| 2 x 5000 W
@4 Ohms Bridged| 2 x 1250 W| 2 x 5000 W| 2 x 5000 W
@8 Ohms Bridged| 4 x 625 / 1 x 1250 W| 4 x 1250 / 1 x 2500 W| 4 x 2500 / 1 x 2500 W
Hi-Z 100V

Hi-Z 70V

230 V AC – 1/8 rated power (4 ohm)

| ****

2.1 A / 420 W

| ****

3.7 A / 840 W

| ****

7.3 A / 1680 W

120 V AC – 1/8 rated power (4 ohm)| 3.6 A / 783 W| 7.2 A / 1556 W| 314.3A / 3132 W
Idle| 0.7 A / 85 W| 0.7 A / 85 W| 0.7 A / 85 W
Thermal Dissipation

(1/8 rated power 4ohm)

| ****

328 BTU/h

| ****

655 BTU/h

| ****

1310 BTU/h

Dimensions W x H x D (mm)| 483 x 89 x 342 mm / 19 x 3.5 x 13.5 in
Weight Net (kg – lbs)| 7 – 15.4

Protections

| Soft-start, Turn-on Turn-off transients, Over-heating, DC, RF, Short- circuit, Open or

mismatched loads, Overloaded power supply, ICL™, PMS™ and SSP™

*IEC filtered pink noise signal (40Hz-5kHz, 12dB crest factor).

TROUBLESHOOTING

We aim to resolve possible issues by providing solutions in this section:

The amplifier does not start up
Check the power supply cord. If it is correctly connected and the red led on the front panel does not light on, check the fuse situated in the input of the power cord.
The amplifier starts up but there is no sound
Check that the amplifier is being provided with a signal in the correct input, A, B, C or D. If the signal does reach the amplifier, the green signal LED will light.
The resulting sound is “strange”
Check that the outputs and their corresponding cabinets are correctly linked. Always be careful in increasing little by little the cabinets volume channel by channel in order to check the correct connection and not to damage the transducers.
One of the cabinets ( with the same signal ) sounds less than the others and the joining cable from the amplifier to the cabinet is well balanced otherwise the output signal will fall 6 dB.

DECLARATION OF CONFORMITY

Lynx Pro Audio S.L. declares that ionic series are in conformity with the following EC directives:

Low Voltage Directive 2006/95/EC
Electromagnetic Compatibility EMC 2004/108/EC
RoHS Directive 2002/95/EC

In accordance with Harmonized European Norms:

EN 60065:2002 Audio, video and similar electronic apparatus. Safety requirements
EN 55103-1:1996 Electromagnetic compatibility. Product family standard for audio, video, audiovisual, and entertainment lighting control apparatus for professional use. Part 1: Emission.
EN 55103-2:1996 Electromagnetic compatibility. Product family standard for audio, video, audiovisual, and entertainment lighting control apparatus for professional use. Part 2: Immunity

LYNX PRO AUDIO GUARANTEE

Lynx products are guaranteed against every kind of manufacturing fault 2 years after the date of sale. When products are under guarantee, the repair and the free supply of the device parts in order to correct any kind of defect are guaranteed by Lynx Pro Audio S.L. In the case that the product could not be returned to the factory for checking and repair, Lynx Pro Audio S.L. would supply all the necessary parts.
Lynx Pro Audio S.L. is not responsible for any damage or defect caused during the transport or caused by undue or improper handling by a non-authorized person during the life of this guarantee.
All our products go through rigorous testing and quality controls. We guarantee the characteristics described here within and their quality against any fabrication defect.
The user loses all warranty rights if he incorporates or carries out any modification to the product if he uses it outside of the stated safe working loads or does not secure the system properly using all the pins in their corresponding holes.
For any question regarding the product, the user must quote the model and serial number.
WEEE Declaration: Electrical and electronic equipment must be disposed of separately from normal waste at the end of its operational lifetime. Please dispose of this product according to the respective national regulations or contractual agreements. If there are any further questions concerning the disposal of this product please contact Lynx Pro Audio S.L.

CONTACT

LYNX Pro Audio S.L.
Calle 1. Pol. Ind. Picassent, Picassent, Valencia 46220 España
+34 961 109 601
www.lynxproaudio.com

Lynx Pro Audio S.L. shall not be liable to the purchaser of this product or to third parties for any damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of an accident, misuse, or abuse of this product, nor for any modifications, repairs, or alterations to it, or for failing to strictly adhere to the operating and maintenance instructions of Lynx Pro Audio S.L.