iHome iBTW112 Wireless Powerboost Fast Wireless plus USB Charging Alarm Clock User Guide

iHome iBTW112 Wireless Powerboost Fast Wireless plus USB Charging Alarm

Clock

Specifications

• Size: folded: 140 x 160 mm, unfolded: 560 x 160 mm
• Printing color: Black (1C + 1C)
• Material: 85 gsm wood-free paper

Product Usage Instructions

Connecting the Unit:

Connect the included AC adapter to the DC jack located on the back of the unit and plug the other end into a working wall outlet.

Manual Bluetooth Pairing:

Turn on your Bluetooth device and make it discoverable. Press and hold the Bluetooth Pairing Button on the back of the iBTW112 until the Bluetooth pairing icon appears solid on the clock display.

Using Wireless Charging:

This unit wirelessly charges phones. Place your device face up on the charging pad. Check the lightning icon on the iBTW112 display for charging status.

Setting your Clock Time:

Follow the instructions in the manual for clock time setting.

Setting and Using the Alarm:

Use the Alarm Button and buttons to set the alarm volume and wake-to alarm source. Press any button to mute the alarm when it sounds.

Adjusting Dimmer Settings:

In Power off mode, use the and buttons to adjust LED display brightness.

Charging Devices Via USB-C Port:

Connect a USB-C cable to the USB-C port on the back of the unit and to your device’s charging port. Ensure the unit is plugged into a working outlet for charging.

Replacing and Installing Clock Backup Battery:

Refer to the manual for instructions on replacing and installing the clock backup battery.

FAQ

• Q: Can I charge my device using the USB-C port?
  • A: Yes, you can charge your device via the USB-C port on the back of the unit. Make sure to use a standard USB-C cable for charging.

What’s Included

The Display

Back Of Unit

Connecting the unit

Connect the included AC adapter to the DC jack located on the back of the unit and connect the other end to a working wall outlet

Manual Bluetooth Pairing

Turn on your Bluetooth device and make it ‘discoverable’ by turning on Bluetooth mode.

• Press the Power Button on the iBTW112.
• Press and hold the Bluetooth Pairing Button on the back of the iBTW112 until the Bluetooth, pairing Icon flashes to indicate the unit is in pairingmode.
• Select ‘iHome iBTW112’ on your device’s Bluetooth menu to connect!
• If pairing is successful, the Bluetooth indicator appears solid on the clock display, indicating the iBTW112 is ready to play music.
•  To reset Bluetooth settings, press and hold the Bluetooth Pairing Button for 10 seconds

Using Wireless Charging

This unit will wirelessly charge phones. Place the device face-up on the charging pad.

Check the lightning icon on the iBTW112 display for charging status:

• Slow blinking icon: The device is charging properly.
• Solid icon: Device is charged.
• Rapid blinking icon: The device is not charging properly. Reposition device.

Note: The lightning icon may continue to blink slowly when iOS devices are fully charged.

CAUTION: Remove metal protective from the phone before charging. When charging a phone, do not place magnetic-striped or other metal objects on the charger. Doing so could damage the object or this unit.

Setting your clock time

Press and hold Power/Time Set Button until the display Flashes . (By default, BT time Sync is set to ON, ON is flashing on display).

• Press the Button toggle BT time Sync ON or OFF, tap Power/Time Set button to confirm. Manual time set only enable when BT time sync is OFF:
• Press Buttons to set Hour, tap Power/Time Set button to confirm.
• Press Buttons to set Minute, tap Power/Time Set button to confirm and complete clock time setting.

Setting and Using the Alarm

This unit features single alarm which can be set to different times and alarm sources. Each is set in the same way.

Note: Each step must be completed while display is flashing or setting will time-out with any changes saved.

1. Press and hold the Alarm Button for 2 seconds until the display flashes. A beep sounds.
2. Press Button to adjust the alarm hour. Press Alarm button to confirm.
3. Press Button to adjust the alarm minute. Press Alarm button to confirm.
4. Press Button to adjust the alarm volume to the volume . Press the Alarm Button to confirm the alarm volume setting.
5. Press Button to select the desired wake-to alarm source. Press Alarm Button to confirm the wake-to-alarm source.
6. Press Button to select the desired wake-to alarm sources: • Alarm Tone 1 • Alarm Tone 2 • Alarm Tone 3 • Alarm Tone 4 • Bluetooth®
7. Press alarm Set Button to confirm and complete alarm setting. (Once alarm is enabled, press alarm button again to disable the alarm)
8. When alarm is sounding, press any button to mute the alarm.

To adjust Dimmer settings:

In Power off mode, LED display brightness can be adjusted using the and buttons. Press button increase display brightness, press button reduce display brightness.

Charging Devices Via USB-C Port

1. Connect the standard-size end of a USB-C cable (not included) to the USB-C port on the back of the unit and connect the other end to the charging port on your device.
2. Monitor the charging on your device. Some devices use a proprietary charging method and will not charge using the USB-C port. If this happens, you must charge your device using the charger that came with it.

NOTE: Unit must be plugged into working outlet to charge devices.

Replacing and Installing Clock Backup Battery

The unit uses two AAA back-up batteries (not included) to provide continuous alarm operation and clock settings in the event of a temporary power failure. When the battery icon on the clock display is flashing, it is time to replace the back-up battery.

The battery compartment is located on the bottom of the unit.

1. Press in and push down on the battery door to open and remove the battery door.
2. Install 2 new “AAA” batteries, matching the (+/-) markings in the battery compartment.
3. Replace the door.

FCC Statement

This equipment complies with FCC RF radiation exposure limits set forth for uncontrolled environments.

This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

• Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
• This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ISED Information

• The device comply with ISED RF exposure requirement, users can obtain Canadian information on RF exposure and compliance.
• This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
• This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
• This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,

Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

IMPORTANT SAFETY INSTRUCTIONS

Please heed all warnings, read and follow all instructions and keep these instructions handy for future reference.

1. Do not use this product near water.
2. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
3. Heat – This product should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat.
4. Only use attachments/accessories specified by the manufacturer.
5. Unplug this product during lightning storms or when unused for long periods of time.
6. Damage Requiring Service – This product should be serviced by qualified service personnel when:
   • Plug has been damaged.
   • Objects have fallen into or liquid has been spilled into the enclosure.
   • The unit has been exposed to rain. The unit has been dropped or the enclosure damaged.
   • The unit exhibits a marked change in performance or does not operate normally.
7. No naked flame sources, such as lighted candles, should be placed on this product.
8. Attention should be drawn to the environmental aspects of battery disposal.
9. This product is suitable for use in tropical and/or moderate climates.
10. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
11. Do not dispose of batteries in the household trash or fire.
12. The mains plug of power adaptor is used as the disconnect device, it shall remain readily operable.
13. Unplug unit and clean only with damp cloth. Stronger cleaning agents, such as Benzene, thinner or similar materials can damage the surface of the unit.
14. CAUTION Risk of explosion if the battery is replaced by an incorrect type.

© 2024 SDI Technologies, Inc. All rights reserved. Questions? Visit www.ihome.com

References

• iHome | Premium Audio Products & Innovative Sound Solutions
• iHome | Premium Audio Products & Innovative Sound Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>