iHome IPBT70 Power Tower Triple Charging Speaker Instruction Manual
- June 1, 2024
- iHome
Table of Contents
Model: iPBT70
POWER TOWER
Triple Charging Speaker
IPBT70 Power Tower Triple Charging Speaker
Charge your iPhone or mobile devices:
– Insert the USB-C cable into the USB-C port of the unit. Connect the other
end to the 25W USB-C adaptor.
– When the iPBT70 is powered OFF, audible voice prompts for wireless charging
are inactive and only the color light bar will flash three times. It will
flash red twice if device remove from pad.
Note: When the iPBT70 is powered ON, audible voice prompts announce “charging”or “earbuds charging”or “watch charging” when a device is placed on the related charging pad. And if device is removed from the pad, the iPBT70 will announce “charging interrupted” or “earbud charging interrupted” or “watch charging interrupted”.
Power Button and Bluetooth® connection operation
- Turn on your Bluetooth device and make it “discoverable” by turning on Bluetooth mode.
- Press and hold the Power Button on the iPBT70. The first time the unit is powered on, it will automatically enter Bluetooth pairing mode.
- Select ‘iHome iPBT70’ on your device to connect BT, press the play/pause button to play or pause BT music.
- To manually pair with new BT device, press and hold the play/pause button for 3 seconds.
- To reset Bluetooth pairing table by press and hold the play/pause button for 10 seconds.
Light Button
Long press the light button to cycle through the 4 light modes:
(1)Slow fade (default) (2)Fast Change (3)Single color (4)0ff
– Short press changes brightness: Low/Med/Hi.
– Remembers last used lighting mode
– Note: Long press the light button to activate lights while unit/BT is
powered off.
IMPORTANT SAFETY INSTRUCTIONS
Please heed all warnings, read and follow all instructions and keep these instructions handy for future reference.
-
Do not use this product near water.
-
Unplug unit and clean only with damp cloth. Stronger cleaning agents, such as Benzene, thinner or similar materials can damage the surface of the unit.
-
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
-
Heat – This pre uct should be situated away from heat sources such as radiators, heat registers, stoves or other appliances {including amplifiers) that produce heat.
-
Only use attachments/accessories specified/supplied by the manufacturer.
-
Unplug this product during lightning storms or when unused for long periods of time.
-
Damage Requiring Service – This product should be serviced by qualified service personnel when:
– Plug has been damaged.
– Objects have fallen into or liquid has been spilled into the enclosure.
– The unit has been exposed to rain. The unit has been dropped or the enclosure damaged.
– The unit exhibits a marked change in performance or does not operate normally. -
No naked flame sources, such as lighted candles, should be placed on this product.
-
Attention should be drawn to the environmental aspects of battery disposal. Many electronics retailers now recycle batteries and other electronic components at no charge. To find a drop-off location near you, visit www.call2recycle.com
-
This product is suitable for use in tropical and/or moderate climates.
WARNING:
– To reduce the risk of fire or electric shock, do not expose this product to
rain or moisture.
– The mains plug of power adaptor is used as the disconnect device, it shall
remain readily operable.
FCC Information
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment.
This device complies with Part 15 of the FCC Rules, operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
- Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- NOTE: This fauipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the ules,
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with minimum distance 20cm (8
inches) between the radiator & your body.
ISED Information
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
The device comply with ISED RF exposure requirement, users can obtain Canadian
information on RF exposure and compliance.
his equipment should be installed and operated with a minimum distance of 20
cm between the radiator and your body.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
For questions and additional information, please visit:
support.ihomeaudio.com/support/
FCC ID: EMOIPBT70A
IC: 986B-IPBT70A
HVIN: iPBT70a
© 2024 SDI Technologies, Inc.
All rights reserved
iPBT70-022924-A
Printed in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>