KLEIN TOOLS 29602 Power Strip Pro Instruction Manual

: September 11, 2024
: KLEIN TOOLS

Table of Contents

KLEIN TOOLS 29602 Power Strip Pro
Product Usage Instructions
CONTENTS
GENERAL SPECIFICATIONS
SYMBOLS ON PRODUCT
FEATURE DETAILS
MOUNTING INSTRUCTIONS
OPERATING INSTRUCTIONS
MAINTENANCE
FCC & IC COMPLIANCE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KLEIN TOOLS 29602 Power Strip Pro

Specifications

Model: Power Strip Pro
Ports: Multi-port AC and USB
Features: Motion-activated LED work light, surge protection
Input: 125V AC

Product Usage Instructions

Supplying Power

Plug the AC Power Cord 14 into a functional standard U.S. 125V AC receptacle.
Turn on the AC Power Switch 1 to supply power to the AC Outlets 2, USB ports 3, 4, and Work Light 7.

Note : Grounded Input LED Indicator 5 will illuminate if an active ground is present, Surge Protection Status Indicator 6 will illuminate if surge protected.

Programming Work Light 7

To manually turn the Work Light on and off, press the Work Light On-Off / Program Button 9.
To program the Work Light’s behavior, press and hold the Work Light On-Off / Program Button 9 for more than three seconds.

Maintenance

When mounting via Through Holes 11, tighten fasteners by hand. Do not use power tools to tighten.
The Power Strip Pro can be mounted to steel surfaces via Rare-Earth Mounting Magnets 10 on the back of the unit.
To conserve energy, the Work Light On-Off / Program Button 9 will stop illuminating 60 seconds after last being pressed.

Frequently Asked Questions (FAQ)

Q: How do I know if surge protection is active?
A: The Surge Protection Status Indicator 6 will illuminate when the unit is surge-protected.
Q: How can I change the modes of the work light?
A: Press and hold the Work Light On-Off / Program Button 9 for more than three seconds to enter Programming Mode. Then cycle through different modes by pressing the button repeatedly.
Q: Can I mount the power strip on steel surfaces?
A: Yes, you can use the Rare-Earth Mounting Magnets 10 on the back of the unit to mount it on steel surfaces.

The Klein Tools Power Strip Pro is a multi-port AC and USB power distributor with powerful motion-activated LED work light and surge protection.

GENERAL SPECIFICATIONS

Operating Altitude: 6562′ (2000 m)
Operating Temperature: 14° to 140°F (-10° to 60°C)
Storage Temperature: -4° to 158°F (-20° to 70°C)
Relative Humidity: 85% non-condensing
AC Power Cord: 6′ (1.8 m), 14 AWG, NEMA 5-15P
AC Power Cord Jacket: SJTW (105C/300V)
AC Input: 125V AC, 15A, 60Hz (nominal)
AC Output: 125V/15A, 60Hz, Max. output 1875W
AC Outlets: 5 × NEMA 5-15R,
Surge Protection: 2160 Joules, Type 3, 600V (L-N, L-G, N-G)
Over-Current Protection: 125V, 15A
USB Output (Total Wattage): 27W
USB-A: 2 × 5V DC, 2.4A (shared)
USB-C: 1 × 5V DC, 3.0A
LED Work Light Output: 500 Lumens
Magnets: Neodymium, N48
Dimensions: 1.85″ × 1.70″ × 23.0″ (4.7 cm × 4.3 cm × 58.4 cm)
Weight: 2.07 lbs (0.94 kg)
Drop Protection: 6.6′ (2 m)
Standards: Conforms To UL STD. 1363

Certified To CSA STD. C22.2 NO. 308

Specifications subject to change.

WARNINGS
Read, understand, and follow these instructions to ensure safe operation and service of the Power Strip Pro. Failureto observe these warnings can result in fire, electric shock, property damage, serious injury and/or death.

Use indoors and in dry locations only. DO NOT expose to moisture, rain, or snow.
DO NOT plug into another relocatable power tap or an extension cord.
DO NOT use the product if damaged or modified.
DO NOT subject to impacts or drops greater than 6.6′ (2 m) (Product Drop Rating). Drops larger than this may not show signs of damage, but internal components may have been compromised. CIt is advisable to replace the unit if any such severe events occur.
Keep away from high voltage devices.
DO NOT exceed the maximum power rating of device (1875W).
DO NOT connect to an ungrounded outlet.
DO NOT use with extension cord adapters that eliminate the ground connection.
NOT for permanent installation – DO NOT remove the plug for permanent connection to the electrical system.
High-intensity LED Light. Avoid looking directly at the work light.
DO NOT attempt to insert other USB connector types into the USB-C and USB-A ports.
CAUTION – DO NOT install this device if there is not at least 10 meters (30 feet) of wire between the electrical outlets and the electrical service panel.
This device features internal protection that will disconnect the surge protective component at the end of its useful life, but will maintain power to the load – now unprotected

SYMBOLS ON PRODUCT

Warning or Caution
Risk of Electrical Shock
Do Not Stare at the Operating Lamp: Visible Radiation
Strong Magnetic Field
Read Instructions
Motion Sensor
Auto-Power Off (10 Minutes)
3s Press for 3 Seconds
Settings
Level VI Efficiency Standard
Independently tested by Intertek and meets applicable standards.
Energy Efficiency Verified

FEATURE DETAILS

AC Power On/Off Switch
125V AC Outlets (×5)
USB-A Charging Ports (×2)
USB-C Charging Port
Grounded Input LED Indicator
Surge Protection LED Indicator
500-Lumen LED Work Light
Work Light Motion Sensor
Work Light On-Off / Program Button
Rare-Earth Mounting Magnets (×2)
16″ On-Center Through Mounting Holes with Location Markers
16″ On-Center Keyholes with Location Markers
15″ On-Center Keyholes with Location Markers
AC Power Cord
Strain Relief

MOUNTING INSTRUCTIONS

NOTE : Disconnect Power Strip Pro from power source before mounting.
NOTE : NOT for permanent mounting. When mounting with a threaded fastener or nail, mark the centerpoints onto the mounting surface using the Mounting Locations on the desired mounting holes 11 , 12 , 13 , the mounting template from the side panel of the retail packaging, or download/print the template using the QR code on the front of this manual. It is recommended to pre-drill pilot holes when using threaded fasteners.
- Through Holes 11 can accommodate up to a 3/8″ (9.5 mm) shank diameter.
- Keyholes 12 , 13 can accommodate up to #8 screws or 10d nails.
NOTE : When mounting via Through Holes 11, tighten fasteners by hand. DO NOT USE POWER TOOLS TO TIGHTEN.
The Power Strip Pro can also be mounted to steel surfaces via the Rare-Earth Mounting Magnets 10 on the back of the unit.

OPERATING INSTRUCTIONS

SUPPLYING POWER

Plug the AC Power Cord 14 into a functional standard U.S. 125V AC receptacle to supply power to the unit.
Turn on the AC Power Switch 1 to supply power to the AC Outlets 2 , USB ports 3 , 4 and Work Light 7 .
NOTE : Grounded Input LED Indicator 5 will illuminate when an active ground is present on AC supply.
NOTE : Surge Protection Status Indicator 6 will illuminate when the unit is surge protected.

PROGRAMMING WORK LIGHT 7

The integrated work light has both manual and automatic functionality:
To manually turn the Work Light on and off, press the Work Light On-Off / Program Button 9 .
To program the Work Light’s behavior, press and hold the Work Light On-Off / Program Button 9 for greater than three seconds to enter Programming Mode. Repeatedly press the Work Light On-Off / Program Button 9 to cycle through the different modes, as indicated by the flashing color of the Work Light On-Off / Program Button 9 . To enter your desired mode, allow the Work Light On-Off / Program Button 9 to flash the appropriate color for 5 seconds, then press the Work Light On-Off / Program Button 9 . There are 3 modes

AUTO-ON/OFF MODE (GREEN):

The Work Light 7 turns ON automatically when motion is detected in a predetermined range. The Work Light 7 remains ON as long as motion is detected, and automatically powers OFF after 10 minutes of detecting no motion. The Work Light 7 may also be manually switched ON/OFF at any time by pressing the Work Light On-Off / Program Button 9 . See MOTION SENSOR section for more details.
NOTE : In AUTO ON/OFF Mode, if the Work Light 7 is turned OFF manually, there will be a 60-second delay before the motion sensor activates the Work Light again.

MANUAL-ON/AUTO-OFF MODE (BLUE):

The Work Light 7 turns ON when user manually presses and releases Work Light On-Off / Program Button 9 . The work light remains ON as long as the device detects activity. The Work Light 7 remains ON as long as motion is detected, and automatically powers OFF after 10 minutes of detecting no motion. The Work Light 7 may also be manually switched OFF at any time by pressing the Work Light On-Off / Program Button 9 .
NOTE : In MANUAL ON/AUTO OFF Mode, the Work Light 7 will not power-ON from motion detection.

MANUAL-ON/OFF MODE (RED):
The Work Light 7 turns ON and/or OFF when user manually presses and releases Work Light On-Off / Program Button 9 .
NOTE : In MANUAL ON/OFF Mode, the Work Light 7 will not power-ON or OFF from motion detection.
NOTE : To conserve energy, the Work Light On-Off / Program Button 9 will stop illuminating 60 seconds after last being pressed. When this happens, the Power Strip Pro is still powered ON, and the Work Light 7 will continue to function according to the last saved mode.
NOTE : The Work Light will power-ON in the same mode as it was in when powered-OFF.

MOTION SENSOR 8

Detection range averages ~9′ (~3 m) from center.
Coverage may vary depending on lighting and/or mounting conditions.
Avoid placing the motion sensor in direct sunlight or bright light.

MAINTENANCE

CLEANING : Be sure the device disconnected from all power sources and devices. Use clean, dry, soft, lint-free cloth to wipe down the entire units. Do not use abrasive cleaners or solvents.
STORAGE : Store in cool temperatures, mild humidity, and away from direct sunlight (See GENERAL SPECIFICATIONS). Leaving in a vehicle or other confined spaces in extreme hot temperatures can lead to decrease in service life, overheating, or fire. Extreme cold temperatures below the specified storage range can also harm performance and service life. Keep away from corrosive chemicals and gases. After taking out of storage, inspect visually to make sure device and all accessories look satisfactory. Allow unit to return to ambient conditions before using

FCC & IC COMPLIANCE

This device complies with part 15 of the FCC RULES and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE : The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulB interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-003(B) / NMB-003(B)

DISPOSAL / RECYCLE
Do not place equipment and its accessories in the trash. Items must be properly disposed of in accordance with local regulations. See www.epa.gov/recycle for additional information.

CUSTOMER SERVICE
KLEIN TOOLS, INC. 450 Bond Street, Lincolnshire, IL 60069 1-800-553-4676 customerservice@kleintools.com www.kleintools.com

Scan to view the How-To Video