BTech BT9926 Full Service Wall Mount For XXL Displays Installation Guide

September 10, 2024
BTECH

BTech BT9926 Full Service Wall Mount For XXL Displays

  • Recommended screen size: 80″ up to 720″ Ideal for mounting 27:9 ultrawide displays
  • Max load: 200kg (4401bs)
  • VESA” & non-VESA fixings: up to 7600 x 800mm
  • Pop-out system provides safe and easy service access – Suitable for recess mounting
  • Depth from wall: 746.5mm – 338.5mm (5.75″ – 73.3″) +/-7mm (0.28″) with micro-adjustment
  • Screen height adjustment: +74mm (0.55″)
  • www.btechavmounts.com

Installation Safety Instructions

Caution: This mount is intended for use only with the maximum weights indicated. Use with equipment heavier than the maximum indicated may result in instability causing possible injury.

Do not attempt to install this product until all instructions and warnings have been read and properly understood. Please keep these instructions for future reference. Please check carefully to make sure there are no missing or defective parts – defective parts must never be used. B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.

General
B-Tech AV Mounts recommends that a professional AV installer or other suitably qualified person install this product. Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and easily damaged if dropped. If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious injury or death both during installation and at any time thereafter. Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing. This weight limit will be clearly stated on each product and its packaging and will vary from product to product.

Product location
Please pay careful attention to where this product is located. Check load capacity of the wall prior to installation as some surfaces are not suitable for installation. Designed for indoor use, this mount is suitable for public or home installation. If located in a public or frequently populated area ensure that the product is out of the immediate reach of people. If any AV equipment is to be suspended over the likely path or location of people then great care should be taken to secure all parts of the installation from falling. When drilling holes it is essential to avoid contact with electrical cables and water or gas pipes contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended. Only drill into structures when you are sure it is safe to do so.

Fixing hardware
It is highly recommended that all fixing screws be used where supplied and that the purpose of all other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models of equipment and set up configurations. The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation. The fixing kit supplied with the product may not be suitable for all walls. If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional or your local hardware store.

Hazard limitation
When routing cables take advantage of any built in cable management features that the product might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling. Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other body parts. Particular attention to the nature of moving parts is required especially when assembling installing and adjusting during set up. Immediately after installation double- check that the work done is safe and secure. Double-check all necessary fixings are present and are of ample tightness. It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible (no more than 6 months apart) to ensure that safety is maintained. If in doubt consult a professional AV installer or other suitably qualified person.

  • B-Tech AV Mounts recommends that this product be installed by a qualified AV technician or other suitably qualified person. B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by im- proper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire. This product must be mounted on a suitable surface and may only be used up to the specified maximum weight.

Parts List

Please keep this for future reference

Item Description Qty
  Pop-Out Wall Mount 2
2 Mounting Arm – Left 2
3 Mounting Arm – Right 2
4 Mounting Rail 7750mm 2
5 MB Sliding Insert B
6 MB x 72mm CSK Screw B
7 Rail End Cap 4
B Interface Arm 2
9 Cable Management Clip 6
70 SAF Long Hex Key

Screen Fixings
A| M6 x 76mm Screw| 4
B| M6 x 25mm Screw| 4
C| M6 x 40mm Screw| 4
D| MB x 76mm Screw| 4
E| MB x 25mm Screw| 4
F| MB x 50mm Screw| 4
G| M6Washer| 4
H| MB x 5mm Spacer| 4
 | MB x 75mm Spacer| 4
 | MB x 25mm Spacer| 4
Wall Fixings
Al| StB x 63mm Coach Screw| B
A2| MB Washer| B
A3| N°.70 Wall Plug| B

Installation Instructions

Mount The Wall Brackets

Installation example: Mounting a Jupiter PANAlOST display

  1. Determine the centre of the screen on the wall and mark 454mm (17.9″) above the centre line for the top fixings on item 7.
  2. Using the top centre holes on item 7, space the wall brackets 1200mm (47.2″) apart.
  3. Use item 7 as a template to mark and then drill the fixing holes on the wall.
  4. Insert item A3 into all fixing holes and then use items Al & A2 to mount item 7 to the wall. Tighten all fixings.

Attach Mounting Rails to Wall Mount

  1. On the back of both rails (item 4), insert 4x item 5 into the top channel.

Note: See fig. 1 for the positioning of insert nuts(item 5) on the back of the rail.

  1. Fix items 2 & 3 to item 4 using items 5 & 6
    Note: Use the 300mm fixings on the mounting arm. See fig 2. for arm positioning on rail.

  2. Fit item 7 to the ends of item 4.

Hook Rails Onto Wall Mount

Hook item 4 onto item 1 and tighten the safety screws* located at the bottom of items 2 & 3.

Optional: Cable management, in suitable postions along the rail (item 4), insert item 9.

Attach Interface Arms To Screen

Fix item B to the rear of the screen using the screen fixing kit (items A -J).

Note: Ensure interface arms are positioned the correct way round and the same holes are used on both arms.

Mount Screen Onto Rails

  1. Using item 8, hook screen onto both sets of rails (item 4).
  2. Tighten the safety screws on the bottom of item 8.

Warning!
Fix/ tie the cables to prevent possible damage. Allow enough slack in cable for the movement of the bracket. Optional Screen Alignment Using Micro- Adjustment.

  1. Using a level, align the screen parallel to the floor with the Y axis adjustment screws.
  2. Use the Z axis knob to ensure that each corner of the screen is equidistant from the wall.

Dimensions

Please keep this for future reference

Contact: info@btechavmounts.com

  • 2024 B-Tech AV Mounts Corporation Ltd. All rights reserved.
  • B-Tech AV Mounts is a division of B-Tech AV Mounts Corporation Ltd.
  • B-Tech AV Mounts and the B-Tech logo are registered trademarks.
  • All B-Tech images and symbols are exclusive property of B-Tech AV Mounts Corporation Ltd.
  • All other brands and product names are trademarks of their respective owners.
  • Any reproduction, retransmission or republication of any part of this manual is strictly prohibited, unless prior written permission has been granted by B-Tech AV Mounts Corporation Ltd.  Photographs are for illustrative purposes only. E&OE
  • www.btechavmounts.com/bt9926

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals