BTECH BT7005 Single Screen Digital Signage Kiosk Installation Guide

BTECH BT7005 Single Screen Digital Signage Kiosk

SPECIFICATIONS

• Designed to portrait mount a single screen display
• Simple ‘hook-on’ screen installation
• Removable front and rear panels for easy installation and maintenance
• Vented grilles allow airflow to and from the device
• Base can be freestanding or bolted to the floor
• Includes internal media storage space in lower section
• For indoor use only

www.btechavmounts.com

INSTALLATION SAFETY INSTRUCTIONS

CAUTION
This stand is intended for use only with the maximum weights indicated. Use with equipment heavier than the maximum indicated may result in instability causing possible injury. \

• Do not attempt to install this product until all instructions and warnings have been read and properly understood.
  Please keep these instructions for future reference.

• Please check carefully to make sure there are no missing or defective parts – defective parts must never be used.
  B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.

• General
  B-Tech AV Mounts recommends that a professional AV installer or other suitably qualified person install this product.
  Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and
  easily damaged if dropped.
  If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious injury or death, both during installation and at any time thereafter.
  Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing.
  This weight limit will be clearly stated on each product and its packaging and will vary from product to product.

• Product location
  Please pay careful attention to where this product is located. Designed for indoor use, this mount is suitable for public or home installation. Check load capacity of the floor prior to installation as some surfaces are not suitable for installation. When verifying the stability of the structure, consider the following external factors: The strength of the floor, exposure to sudden and severe wind and danger arising from contact with people and/or objects (eg installations in passageways, emergency exits), if located in a public or frequently populated area ensure that the product is out of the immediate reach of people. When drilling holes it is essential to avoid contact with electrical cables and water or gas pipes contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended. Only drill into structures when you are sure it is safe to do so.

• Fixing hardware
  It is highly recommended that all fixing screws be used where supplied and that the purpose of all other fixing hardware
  is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models of equipment and set up configurations. The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation.
  If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional or your local hardware store.

• Hazard limitation
  When routing cables take advantage of any built in cable management features that the product might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling. Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other
  body parts. Particular attention to the nature of moving parts is required especially when assembling installing and adjusting during set up. Immediately after installation double-check that the work done is safe and secure. Double- check all necessary fixings are present and are of ample tightness.
  It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible (no more than 6 months apart) to ensure that safety is maintained.
  If in doubt consult a professional AV installer or other suitably qualified people.

BT7005 PARTS LIST

PLEASE KEEP THIS FOR FUTURE REFERENCE

Note: Images for reference only as sizes may differ depending on installation type.

INSTALLATION TOOLS REQUIRED

INTERFACE KIT
A| M6 x 16mm SCREW| 4
B| M6 x 25mm SCREW| 4
C| M6 x 40mm SCREW| 4
D| M6 x T1.5mm WASHER| 4
E| M8 x 16mm SCREW| 4
F| M8 x 25mm SCREW| 4
G| M8 x 40mm SCREW| 4
H| 5mm SPACER| 4
I| 13mm SPACER| 4
J| 24mm SPACER| 4

INSTALLATION INSTRUCTIONS

REMOVE PANELS AND STORAGE TRAY FROM KIOSK

1. Using item 17, unlock item 5 and remove from item 2.
   

2. Attach item 8 to item 3 using item 9, lift item 8  up and pull the front panel (item 3) away from item 2.

3. Attach item 8 to item 4, lift up and remove the back panel (item 4).
   REMOVE AV TRAY FROM KIOSK BODY

4. Unscrew item 7 and remove item 6 from item 2.
   

ASSEMBLE KIOSK BODY TO BASE

Fix item 2 onto item 1 using items 13, 14 & 15.

OPTIONAL BOLT BASE TO THE FLOOR
Note: The kiosk can be used freestanding or item 1 can be bolted to the floor using suitable floor fixing kit (not supplied).

FIX INTERFACE ARMS TO SCREEN

Fix item 10 to the rear of the screen using the screen interface kit (items A – K).
Note: Ensure the arms are facing the correct way round and the same holes are used on both arms.

PORTRAIT MOUNTING SHOWN

![BTECH BT7005 Single Screen Digital Signage Kiosk-8]](https://manuals.plus /wp-content/uploads/2022/02/BTECH-BT7005-Single-Screen-Digital-Signage- Kiosk-8.jpg)

MOUNT SCREEN ONTO KIOSK

Using item 10, hook the screen onto the mounting rail on the front side of item 2.

Note: Ensure the interface arms hook correctly onto the rail.

FIX AV TRAY TO KIOSK

1. Attach AV hardware to the storage tray (item 6).
2. On the back side of the kiosk, fix item 6 to item 2 using item 7.
   

RETURN THE FRONT PANEL & ADJUST THE SCREEN

1. Using item 8, return item 3 to item 2 (see Step 2 for reference).
2. Using the micro-adjustment handwheels on item 10, align the screen with the cut-out on the front panel (item 3).
3. Use the cable management holes to tidy any cables.
4. Tighten the safety screws on the bottom of item 10, securing the screen to the rail.
   

RETURN BACK PANEL & TOP PANEL TO KIOSK

1. Hook item 4 back onto item 2.
2. Fit and lock item 5 onto the top of item 2 using item 17.
   

THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.

CONTACT:
info@btechavmounts.com

©2021 B-Tech International Design and Manufacturing Ltd. All rights reserved.
B-Tech AV Mounts is a division of B-Tech International Design and Manufacturing Ltd. B-Tech AV Mounts and the B-Tech logo are registered trademarks.
All other brands and product names are trademarks of their respective owners. Photographs are for illustrative purposes only. E&OE.
AMA-BT7005-V1-1021-BTECH MADE IN THE UK
For More Information Visit www.btechavmounts.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>