BTECH BT8390-WFK6 Adjustable Height or Depth Rail Mounting Bracket Installation Guide
- June 12, 2024
- BTECH
Table of Contents
BTECH BT8390-WFK6 Adjustable Height or Depth Rail Mounting Bracket
SPECIFICATIONS
- Designed to wall mount a BT8390, BT8391 or a BT8392 horizontal rail
- Mounts rail 67mm (2.65″) from wall with +/-10mm (+/-0.4″) adjustable depth and +/-10mm (+/-0.4″) adjustable height to ensure a flat to the wall installation
- Max load 50kg (11 0lbs) per mounting bracket Max load 100kg (220Ibs) when used as a pair
- Can also be pole mounted using B-Tech accessory collars.
INSTALLATION Ii OPERATING SAFETY INSTRUCTIONS
CAUTION: This mount is intended for use only with the maximum weights indicated. Use with equipment heavier than the maximum indicated may result in instability causing possible injury.
Do not attempt to install this product until all instructions and warnings
have been read and properly understood.
Please keep these instructions for future reference.
Please check carefully to make sure there are no missing or defective parts –
defective parts must never be used. B-Tech AV Mounts, its distributors and
dealers are not liable or responsible for damage or injury caused by improper
installation, improper use or failure to observe these safety instructions. In
such cases, all guarantees will expire.
General
B-Tech AV Mounts recommends that a professional AV installer or other suitably
qualified person install this product.
Great care must always be taken during installation as most AV equipment is of
a fragile nature, possibly heavy and easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install
this product safely, then please consult a professional for advice and/or to
install this product for you. Failure to mount this product correctly may
cause serious injury or death both during installation and at any time
thereafter.
Do not mount any AV equipment that exceeds the specific weight limit of the
product you are installing.
This weight limit will be clearly stated on each product and its packaging and
will vary from product to product.
Product location
Please pay careful attention to where this product is located. Check load
capacity of the wall prior to installation to ensure that it can support the
combined weight of the equipment and hardware, some surfaces are not suitable
for installation.
Warning! Secure to a solid fixture, stability can be impaired if
attaching to any unsecured surface or furniture.
Designed for indoor use, this mount is suitable for public or home
installation. If located in a public or frequently populated area ensure that
the product is out of the immediate reach of people. f any AV equipment is to
be suspended over the likely path or location of people then great care should
be taken to secure all parts of the installation from falling.
When drilling holes it is essential to avoid contact with electrical cables
and water or gas pipes contained within.
Use of a good quality live wire detector and hidden object locator is
therefore recommended.
Only drill into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that all fixing screws be used where supplied and
that the purpose of all other fixing hardware is fully understood. In some
cases more AV equipment fixing hardware will be supplied to accommodate
different models of equipment and set up configurations. The installer must be
satisfied that any supplied fixing hardware is suitable for each specific
installation. The fixing kit supplied with the product may not be suitable for
all walls.
If any fixing screws or included hardware are deemed not sufficient for a safe
installation then please consult a professional or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features that the product might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling. Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other body parts. Particular attention to the nature of moving parts is required especially when assembling installing and adjusting during set up. Immediately after installation double- check that the work done is safe and secure. Double-check all necessary fixings are present and are of ample tightness.
Operating & Maintenance
It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible (no more than 6 months apart) to ensure that safety is maintained. B-Tech AV Mounts recommends that a suitably qualified person is used for the removal of this product. Please dispose of the product carefully and with consideration to the environment. If in doubt consult a professional AV installer or other suitably qualified person.
PARTS LIST
ITEM
| PART NAME|
QTY
---|---|---
1
| ADJUSTABLE WALL PLATE| 1
2| INSERT NUT|
2
3
| M8 x 12mm HEX SCREW| 2
4| SAF HEX KEY|
1
WALL FIXING KIT
A1| M8 x 50mm COACH SCREW|
2
A2
| M8WASHER| 2
A3| WALL PLUG|
2
Max load: 50kg (11 0lbs) per mounting bracket
Max load: 100kg (220Ibs) when used in pairs
INSTALLATION TOOLS REQUIRED
-
Drill
10mm (7/16″) masonry bit or 6mm (1 /4″) wood bit -
Pencil 13mm (5/16″)
-
Spanner or Socket
-
Level
-
Stud Finder (Optional)
INSTALLATION INSTRUCTIONS
FIX WALL BRACKET(S) TO RAIL
Insert item 2 into the top and bottom channels of a BT8390 Rail (not
supplied).
Note: The max distance between wall brackets is 1500mm (59″).
Each wall bracket can hold a max load of 50kg (11 0lbs).
Ensure a suitable quantity of wall brackets are used for the installation.
FIX BRACKET AND RAIL TO THE WALL
- Mark and drill the bracket fixing holes in the wall.
- Use the top item A 1 fixings to hook on item 1.
- If necessary, laterally adjust the rail into position.
Repeat this step and fix all rails needed for the install.
ADJUST RAILS TO ALIGN
Use a level, plumb line, a spirit and the depth adjustment screws to align
rails vertically and horizontally.
Note: Use the adjustment guides to help align rails precisely.
TYPICAL INSTALLATIONS
DIMENSIONS
**TOP VIEW
**
FRONT VIEW
REAR VIEW
SIDE VIEW
SIDE VIEW
with BT8390 RAIL (Centre depth)
THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
CUSTOMER SUPPORT
©2023 B-Tech International Design and Manufacturing Ltd. All rights reserved.
B-Tech AV Mounts is a division of B-Tech International Design and
Manufacturing Ltd.
B-Tech AV Mounts and the B-Tech logo are registered trade marks.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
AMA-BT8390-WFK6-V1-0123-50 MADE IN THE U.K.
For More Information Visit www.btechavmounts.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>