OLIMPIA SPLENDID B1130 Wireless Kit Instruction Manual
- September 11, 2024
- OLIMPIA SPLENDID
Table of Contents
OLIMPIA SPLENDID B1130 Wireless Kit
Specifications
- Communication Protocol: Wireless
- Operating Frequency Band: 2.412 GHz to 2.484 GHz
- Maximum Transmitted Power: 19.5 dBm
- Communication Standard: IEEE 802.11 b/g/n
- Antenna: Integrated into PCB
FAQ
Q: What should I do if the wireless connection is unstable?
A: Check for any obstructions or interference near the device that could disrupt the wireless signal. You can also try restarting the device or repositioning it for a better connection.
Q: How do I reset the wireless kit?
A: Locate the reset button on the kit and press it for a few seconds until the indicator lights flash, indicating a successful reset.
GENERAL INFORMATION
- The Wireless Kit B1130 allows to check the operation of the prepared terminal to which it is connected, based on the commands sent from the app installed in a smartphone, iphone, tablet or Ipad.
- This manual has been conceived with the purpose of provide You with all the explanations necessary to be able to manage Your system at best.
- Carefully read this manual before proceeding with any operation (installation, mainte-nance, use) and scrupulously respect what is described in the single chapters; This manual has to be considered as an integral part of the instruction, installation and use manual accompanying the system terminals of OLIMPIA SPLENDID.
- Both manuals must be preserved with care and shall ALWAYS accompany the appliance, even in the event of its sale to another owner or user or of a transfer to another plant. In case of damage or loss of the manual, ask for another copy to your local OLIMPIA SPLEN-DID’s Technical Assistance Service.
WARRANTY
Olimpia Splendid provides a guarantee that this appliance will be free of
defects attrib-utable to manufacturing defects in compliance with the L.D.
24/02 of 02/02/2002. Any other problem linked to what below remains excluded
from warranty:
- Wrong installation.
- Exceptional weather events.
- Tampering by unauthorized personnel.
- This appliance shall only be destined for the use for which it has been expressly conceived. Any other use must be considered as improper and therefore, dangerous. The manufacturer cannot be considered liable for possible damages resulting from improper, wrong and unreasonable uses.
- Do no let children or incapable people use the appliance unattended.
- In case of fault and/or malfunction of the system, switch it off and do not tamper with it. For the possible repair, please exclusively refer to the technical assistance centres authorized by the manufacturer and request the use of original spare parts. Failure to respect what is explained above may hinder the system safety.
- In the event of dismantling of the system, proceed with the sorted disposal of the single components according to the dispositions of the local laws. It is also recommended to make those parts of the appliance susceptible to constitute a danger harmless, especially for children which may use the appliance out of service for their own games.
WARNINGS
-
Installation must be carried out by qualified personnel.
-
It is essential to apply all the notions described in this manual.
-
THE MANUFACTURER ASSUMES NO LIABILITY FOR DAMAGES TO PEOPLE OR PROPERTY RESULTING FROM THE LACK OF RESPECT OF THE STANDARDS CONTAINED IN THIS BOOKLET.
-
The manufacturer reserves the right to apply changes at any moment to his own models, notwithstanding he essential characteristics de-scribed in this manual.
-
During the assembly, and upon any maintenance operation, it is necessary to respect the precautions mentioned in this manual and in the one of the terminal, and adopt every precautions suggested by common sense and by the Safety Standards in force in the place of installation.
-
After removing the packaging, make sure of the appliance intactness; the elements of the packaging must not be left within the reach of children, as they constitute a potential source of danger.
-
The Wireless kit must be installed in a system terminal placed next to the router.
In the event of an excessive weakening of the Wireless signal, the app OS Smart System may disconnect more easily when the signal weakens. -
The device transmits at a frequency of 2.4 GHz.
-
The connection quality to a wireless network may result influenced by the presence of electromagnetic smog.
-
This unit complies with the European directives
-
ETSI EN 301 489-1 V2.2.3:2019
-
ETSI EN 301 489-17 V3.2.4:2020
-
ETSI EN 300 328 V2.2.2:2019
-
The simultaneous use of this appliance next to other radio frequency appliances may compromise the quality of the transmitted/received signal until the communication is interrupted.
-
The device uses a non-harmonized frequency and is conceived to be used in European countries; for the use restrictions of this equipment, refer to the specific standards in force for each country.
-
In the countries part of the EU, the WLAN can therefore be used indoors without any restriction, but in Frnace it cannot be used out-doors.
-
Changes or modifications not expressly approved by the party re-sponsible for conformity may nullify the authorization of the user to use the equipment.
-
Check compatibility of the device used with the OS Smart System app in the list on the digital stores.
OLIMPIA SPLENDID is not responsible for any problem deriving from the incompatibility.
TECHNICAL DATA
WIRELESS COMMUNICATION PROTOCOL
- Operating frequency band……………………………..from 2,412 GHz to 2,484 GHz
- Maximum transmitted power…………………………..19,5 dBm
- Communication standard……………………………….IEEE 802,11 b/g/n
- Antenna………………………………………………………Integrated in the PCB
COMPATIBILITY
Before proceeding with the installation of the kit B1130, check the serial
number of the terminal. If the fifth symbol of the serial number is a letter
present in the list below, the printed circuit board is not compatible and
it’ll be necessary to contact the assistance service for the installation.
The fifth symbol must not be :
“ A – B – C – D – E – F – G – H – I – L – M – N – P – R – S – U – V – X – Z ”.
DESCRIPTION OF THE KIT
CONTENT OF THE KIT
KIT ASSEMBLY (FIG.1)
- Connect the connector (A) to the terminal (B1) of the kit cable (B).
- Make sure that a “Click” is heard during the connection for the correct linking of the two terminals.
LIST OF COMPONENTS (FIG.2)
- Modbus connector
- Reset button
- Cloud led
- Modbus led
- Feeding strip
INSTALLATION AND REPLACEMENT OF THE WIRELESS KIT
The following actions for correct installation are not necessary if the kit is
supplied pre-mounted on the terminals.
To access the indicated points of connection, please refer to the main manual
of the terminal, where the operations to be performed for correct removal of
the parts of the shell are indicated.
CONNECTION WITH THE PRINTED CIRCUIT BOARD
- Remove the necessary parts of the terminal to access the printed circuit board.
- Connect the connector (1) of the Kit B1130 as shown in figure.
- The printed circuit board model may vary according to the model.
CONNECTION WITH THE DISPLAY
- Remove the necessary parts of the terminal to access the rear part of the display.
- Connect the feeding strip (5) of the Kit B1130 as shown in figure.
INSTALLATION OF THE APP
DOWNLOAD OF THE APP
Before performing the installation of the app, check for compatibility of the
device on the used store.
-
The App OS Smart System can be downloaded from Google Play Store and iPhone App Store
-
The App OS Smart System can be subject to changes without prior notice, designed to improve its characteristics and performance.
TERMINAL PAIRING PROCEDURE
- The following images describe the actions to be carried out to add a new terminal to the network.
- For the pairing procedure between the electronic device and the system terminal, follow the instructions indicated inside the APP.
APP USER GUIDE
LOGIN
From the starting screen it is possible to perform two operations in order to
login:
-
Log in by clicking on “Sign up” and follow the instructions.
-
Access using the credentials already in your possession.
-
It is possible to save your access cre-dentials by checking the“Remember me” box before Logging in.
DEVICE PAIRING
To pair the first device it is necessary to:
Click on “+” and follow the instructions to configure your device.
To pair other devices it is necessary to:
- Click on the top left corner and make the drop-down menu appear.
- Click on “add device”.
- Press on the icon “Bi2” and follow the instructions to configure your device.
USE OF THE DEVICES
Select the desired device from the drop-down central menu.
It is possible to configure the following func-tions:
-
Fan speed
-
Desired temperature increase
Desired temperature decrease -
Activation of manual mode
Activation of programming -
Operating mode
The data transmission from the device to the App occurs at reduced speed with respect to the data transmission from the App to the device.
Furthermore, it is possible to display the fol-lowing information:
- Outdoor weather (in the place where it has been paired for the first time)
- Indoor temperature
- Set temperature
- Usage statistics of the device
To access the daily programming settings page, press the icon:
- Select the day in which programming must be set.
- Use “+” to set up to 4 time bands.
- Press on the icon in the top right corner to duplicate the settings on another day.
Select a quarter to change the settings:
-
Fan speed
-
Desired temperature
-
3a. Band activation time ()
3b. Band deactivation time ()- To confirm the changes, press (4).
- To cancel the changes, press (5).
- To delete the time band, press (6).
- (*) The configuration of the time bands has no effect on the switching on and switching off of the machine.
- To perform the set operating modes, the terminal must be on.
APP SETTINGS
To access the settings of the app, click in on the top left corner and display
the drop-down menu.
In this drop-down menu it is possible to perform the following options:
-
Add device
(see par. “Device pairing”) -
Settings
(see the following screen) -
Support
request support by sending an e-mail to the assistance service -
Rated Us
rate the app through the store -
Logout
logout from the app
In this drop-down menu it is possible to perform the following options:
- Display the name with which the login has been performed
- Display the mail with which the login has been performed
- Display and/or change the name of your device
- Display and/or change the network to which you are connected
- Display the software version
- Enable/disable sharing the information of the app with the technical support
- Display the app version
Press the icon on the top right corner to delete the device or the account
TROUBLESHOOTING
LED status Operating conditions What to do ?
Green Led mod-bus (4)| OFF| Not permitted| Check connection with the
display and restart the terminal
---|---|---|---
Slowly flashing| Mod-bus enabled but not connected to the terminal| Check the
connection cable with the terminal board (A)
Quickly flashing| Mod-bus enabled and connected to the terminal| The device is
connected
and ready for configuration
Before proceeding with the check of the wireless connection, make sure the mod-bus is enabled and connected to the terminal.
Blu Led cloud| OFF| Wireless connection not enabled| Check connection
with the display and perform the pairing procedure
---|---|---|---
Slowly flashing
(one second)
| Wireless connection active
but not configured
| Perform the configuration
procedure through the APP
Steady| Wireless connection active
and configured
| The device is configured
and ready for use
DISPOSAL
This symbol on the product or its packaging indicates that the appliance
cannot be treated as normal domestic trash, but must be handed in at a
collection point for recycling electric and electronic appliances. Your
contribution to the correct disposal of this product protects the environment
and the health of your fellow men. Health and the environment are endangered
by incorrect disposal. Further information about the recycling of this product
can be obtained from your local town hall, your refuse collection service, or
in the store at which you bought the product. This regulation is valid only in
EU member states.
OLIMPIA SPLENDID spa
via Industriale 1/3
25060 Cellatica (BS)
www.olimpiasplendid.it
info@olimpiasplendid.it
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>