CDP LiSmart-855 Virtual Guatemala User Manual

September 9, 2024
CDP

CDP LiSmart-855 Virtual Guatemala

This manual contains important safety instructions. Keep this manual handy for future reference.

INSTALLATION AND OPERATION
Before installing, please read and understand the following instructions:

Inspect the following items inside the box

  • User manual
  • UPS
  • Mains cord

UNPACKING AND INSPECTION

Examine the packing carton for damage. Notify your dealer immediately if damage is observed. Store the packing in a safe place for possible future trans-shipment of the UPS.

PLACE THE UPS
Position the UPS on a sturdy, dry surface in a well-ventilated area away from direct sources of heat. Leave at least 100 mm clearance all around the UPS to provide adequate ventilation.

The UPS is intended for indoor use only. Although your UPS is very rugged, its internal components are not sealed from the environment. Kindly note the following.

  • Avoid direct sunlight.
  • Avoid excessive heat.
  • Avoid excessive humidity or liquids.
  • Avoid excessive dust

CONNECT UPS TO POWER
Connect the power cord, to a verified grounded 3-wire receptacle. Do not power the UPS use a surge suppressor or power strip. Switch the utility power ON.

CONNECT EQUIPMENT TO UPS
Now connect your load to be protected (computer, monitor, etc.) to the AC output receptacles at the rear of the UPS.

  • do not connect a laser printer or any non-computer peripherals to UPS outlets
  • do not connect a surge suppressor, power strip, or extension cord to the UPS outlet.
  • Enable the UPS by turning on the power ON/OFF switch, which is situated on the front panel.
  • The UPS is now ready to use. Switch on your equipment and you are ready to function.

Safety notice
The product contains voltage, which is potentially hazardous. Qualified service personnel should perform all repairs. Do not try to open the cover and service the system yourself, no user-serviceable parts inside. Refer servicing to qualified service personnel only. The product has its internal energy source (battery). The output receptacles may be live even when the product is not connected to an AC supply.

Warning
In case of a fire risk, please change the fuse with the same kind and same rate. The product is intended for indoor use only. Kindly note to avoid excessive heat, dust, humidity, or liquids.

BATTERY MAINTENANCE/ BATTERY CHARGING
After shipment from the factory, the battery needs recharging. If not used for a long period, the battery will start self-discharging, which may result in a short service life of the battery or may even cause damage to it during the warranty period. Care should also be taken to avoid excessive temperature around the UPS, which could also result in reducing the service life of the battery. The achieve maximum service life from the battery the above instructions should be followed. The UPS battery charges whenever the UPS is connected to utility power & is switched ON. It typically requires more than 12 hours to charge fully. Operating runtime is reduced until the battery is fully charged.

UPS INDICATORS AND CONTROLS

  1. ON/ OFF switch
  2. USB output (5V/2A)
  3. Battery capacity
  4. The output voltage is displayed by default.
  5. Press the ON/OFF buttons to switch the display for the following parameters in turn:
  6. Load percentage
  7. Load level (included “1.2.3” three levels, the higher the level, the greater the load)
  8. Main input voltage

SPECIFICATIONS

DESCRIPTION

  1. Power ON button
  2. Display LCD
  3. USB charger
  4. outlets back up (LiSmart-855) / 4 outlets back up (LiSmart-1206)
  5. 2 outlets surge only
  6. USB communication interface
  7. Breaker protection
  8. AC input

Test the UPS
To test UPS on battery back-up, switch off the utility supply and observe the ‘back-up indicator’ lights. Also, your PC should continue to function normally.

  1. Switching on
    Press the switch for 3 seconds, the LED displays the output voltage, and then the UPS will be ready for operation.

  2. Autorun
    In DC mode, UPS discharges till the battery runs out and cuts off, autorun when the AC recovers.

  3. Overload protection
    When UPS is overloaded while operating, which is not solved by the user in time, it will cut off the output automatically after some time, and then turn back to operation mode.

  4. Low battery shut-off
    When the battery is about to be exhausted, UPS will shut down automatically to protect the battery’s life.

Switching off

  1. AC normal seconds.
  2. Backup
  3. UPS will cut off the output and go to AC standby mode by pressing the switch for 3 Press the switch for 3 seconds, the UPS will be turned off after a long beep.

TROUBLESHOOTING

The troubleshooting chart covers most of the difficulties that you may encounter under normal working conditions. To use the monitoring software, please download the user manual from our website: www.cdpenergy.com.
If the UPS fails to operate properly, please review the following steps before calling the service center.

  1. Is the UPS plugged into the correct working outlet?
  2. Is the line voltage within the rating specified?
  3. Is the fuse/circuit protector on the back panel open?

Please submit the following information when you call for service.

  1. Model No. & Serial No.
  2. Date of problem
  3. Full description

WARRANTY
CHICAGO DIGITAL POWER INC. warranties this product against defective materials or workmanship for one year from the date of original purchase) with the possibility to be extended to 2 years). Proof of purchase is required. To make this warranty valid proof of purchase is required. Bring the product to the original purchase place or the nearest CDP service center. Make sure to bring also this warranty policy. For information about service centers in your country please call the following numbers. (If your country is not here please send a mail to servicio@cdpups.com)

Bolivia: 800-100156
Salvador: 800-6773
Panama: 011-00800-2268611
Colombia: 01800-5181617
Honduras: 800-2561-6099
Peru: 0800-54674
Costa Rica: 800-4357237
Mexico: 001800-5148611
Dominic Republic: 1888-7514876
Venezuela: 0800-1627485

Chicago Digital Power will repair or replace the product at its criteria without a cost during the warranty period. Repair or replacement time should never exceed 30 days from the date that the unit is received at the CDP Service Center.
In case this warranty policy is lost please a copy to the original purchase place.

Warranty Limitations
Bolivia: 800-100156
Colombia: 01800-5181617
Costa Rica: 800-4357237
El Salvador: 800-6773
Honduras: 800-2561-6099
Mexico: 001800-5148611
Panama: 011-00800-2268611
Peru: 0800-54674
Dominic Republic: 1888-7514876
Venezuela: 0800-1627485

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals