OVO KIT-LV30 Central Vacuum Carpet Deluxe Kit User Manual

: June 17, 2024
: OVO

Table of Contents

INCLUDED IN THE KIT
HIGH-VOLTAGE HOSE
CARPET BEATER SPECIFICATIONS
HIGH-VOLTAGE WAND SPECIFICATION
INSTRUCTIONS
LOW-VOLTAGE WAND
INCLUDED CLEANING TOOLS
EASY STORAGE INCLUDED
HOW TO REPLACE THE BELT
HOW TO REPLACE THE BELT
HOW TO REPLACE THE BRUSH ROLL
HOW TO REPLACE THE HEAD LIGHT
CLOG IN THE POWER NOZZLE
TROUBLE SHOOTING GUIDE
Customer Support
Documents / Resources

OVO KIT-LV30 Central Vacuum Carpet Deluxe Kit User

OVO KIT-LV30 Central Vacuum Carpet Deluxe Kit

INCLUDED IN THE KIT

High-voltage hose with dual control switch
Adjustable Low-Voltage wand
Adjustable High-Voltage wand
Electrical carpet beater
12’’ Floor brush
Dusting Brush
Upholstery Brush
Crevice Tool
Accessory Bag
Chrome hose hanger

HIGH-VOLTAGE HOSE

Compatibility

The hose is compatible with most wall inlets. Inlets must have a 1.5’’ inner diameter (A) in order for the hose to fit, and must have 2 low-voltage pins/metal prongs (B) in order to turn the vacuum ON and OFF from the switch located on the hose handle.

Connecting the hose to the wall inlet

The hose end cuff must be connected as shown in the picture below. The black part on the end cuff must be well aligned with the 2 pins inside the inlet (C). The plastic square must be facing up (D).

Dual switch control

Suction activation only: When using floor brush and accessories
Turn the unit off
Suction and carpet beater activation

72’’ pigtail (power cord)

CARPET BEATER SPECIFICATIONS

Carpet Beater (Power head)

Brush roll ON/OFF switch
Overload protector reset
Carpet height indicator
Dirt sensor
Carpet height adjustment
Handle position release
Wand release latch

HIGH-VOLTAGE WAND SPECIFICATION

Hose nozzle release button
Hose nozzle connection
Wand extension handle
Carpet beater connection

INSTRUCTIONS

Connecting the wand to the electric carpet beater (powerhead)

Carpet beater port
Wand Port
The OVO electric wand has female ports to connect to the electric carpet beater (powerhead).
Electrical wand port
Carpet beater (Powerhead) port
The OVO electric carpet beater (powerhead) has male ports to connect to the electric wand.
Connection or the wand to the beater
Connection
To connect the wand to the electric carpet beater, align the female ports (from the wand) and the male connectors (from the carpet beater), then push the wand into the beater.

Connecting the high-voltage hose to the wand

Hose nozzle port
Hose port
The hose nozzle must have two female ports in order to connect it to the wand.
Electrical wand port
Wand ports
Our electric wand has 2 male ports.
Connection of the hose nozzle to the wand
Connection
Align the female ports from the hose nozzle with the male ports on the wand and push the hose nozzle into the wand.

LOW-VOLTAGE WAND

How to extend the wand

To extend the wand, simply push on the button (E) and pull on the wand (F) at the same time
How to connect the wand to the hose nozzle
Align the hose nozzle button (G) with the lock button on the wand (H) and push the nozzle in the wand until you here a “click”
How to connect the different attachment tools
Insert the other end of the wand into the port on the brushes| | |
---|---|---|---

INCLUDED CLEANING TOOLS

12’’ Superior Floor brush
Ideal for hard surfaces. Made of horse hair – Will not scratch your floor
Dusting brush
Made of horse hair – Delicate and soft on furniture
Upholstery brush
Made of horse hair – Perfect for delicate furniture
Crevice tool
Ideal to clean cracks and crannies

EASY STORAGE INCLUDED

Chrome hose hang
The perfect accessory to store your hose neatly.
Accessory bag
2 Large pockets to make it easy to store your accessories without making a mess in your storage room.

HOW TO REPLACE THE BELT

ALWAYS DISCONNECT THE VACUUM AND THE HIGH-VOLTAGE HOSE FROM THE ELECTRICAL OUTLET BEFORE PROCEEDING WITH THE FOLLOWING MAINTENANCE.

Belt Replacement

The belt installed in the electric carpet beater (powerhead) makes the brush roll turn. It has been specifically designed for our electric carpet beater and is required to ensure a flawless operation.

Always follow these procedures to verify or replace the belt in order to avoid damaging the carpet beater.

STEP 1 Unscrew the powerhead cover

Disconnect the wand from the electric carpet beater (powerhead).
Turn the electric carpet beater (powerhead) so that the bottom is facing you.
Remove the 7 screws as illustrated above.

STEP 2 Remove the powerhead cove

Turn the electric carpet beater (powerhead) so that the top part is facing you and lift the cover (B) to remove it.
Belt Replacement

STEP 3 Remove the brush roll cover

To remove the brush roll cover, remove the screws as illustrated above and lift the cover to remove it.
Belt Replacement

Do not remove the 3 screws in a triangle formation as these hold the motor in place

HOW TO REPLACE THE BELT

STEP 4 Verify/remove the belt

If the belt is stretched or cut, pull it out from the motor pulley, as illustrated above.

STEP 5 Remove/replace the belt

Lift the end of the brush roll.
Remove the old belt and replace it with the new one. Make sure the lettering is facing you and that it is visible.
Stretch the belt and attach it to the motor pulley.

STEP 6 Replace the brush roll

Hold the opposite end of the brush roll in place.
Push the belt end forward and down while rotating the endplate until it slides into place.
Turn the brush roll to make sure it rotates freely.

STEP 7 Replace the brush roll

Put the brush roll cover back over the brush roll.
Replace the 2 screws and make sure the cover is well attached

STEP 8 Replace the carpet beater (powerhead) cover

The wand port must be in the upright position and locked in place.
Put the cover back on top of the electric carpet beater (powerhead).
Turn the carpet beater (powerhead) over.
Replace the screws, as illustrated in step 1.

STEP 9 Screw the powerhead cover in place

Replace the 7 screws as illustrated above.

HOW TO REPLACE THE BRUSH ROLL

Always follow these procedures to verify or replace the brush roll in order to avoid damaging the carpet beater.

To check if the brush roll needs to be changed, slide cardboard across the bottom plate while turning the brush roll. If the brushes do not touch the cardboard, it is time to change the brush roll.

STEP 1 Unscrew the powerhead cover

Disconnect the wand from the electric carpet beater (powerhead).
Turn the electric carpet beater (powerhead) so that the bottom is facing you.
Remove the 7 screws as illustrated above.

STEP 2 Remove the powerhead cover

Turn the electric carpet beater (powerhead) so that the top part is facing you and lift the cover (B) to remove it.

STEP 3 Remove the brush roll cover

To remove the brush roll cover, remove the screws as illustrated above and lift the cover to remove it.

Do not remove the 3 screws in a triangle formation as these hold the motor in place

Always follow these procedures to verify or replace the brush roll in order to avoid damaging the carpet beater.

STEP 4 Remove/replace the brush roll

Lift the end of the brush roll to release the belt.
Remove the old brush roll and replace it with the new one.
Loop the belt around to the motor pulley.
Make sure the belt is sitting in the “belt groove” on the brush roll.

STEP5 Replace the brush roll

Hold the opposite end of the brush roll in place.
Push the belt end forward and down while rotating the endplate until it slides into place.
Turn the brush roll to make sure it rotates freely.

Replace the brush roll cover

Put the brush roll cover back over the brush roll.
Replace the 2 screws and make sure the cover is well attached.

STEP 6 Replace the carpet beater (powerhead) cover

The wand port must be in the upright position and locked in place.
Put the cover back on top of the electric carpet beater (powerhead).
Turn the carpet beater (powerhead) over.
Replace the screws, as illustrated in step 1.

STEP7 Screw the powerhead cover in place

Replace the 7 screws as illustrated above.

HOW TO REPLACE THE HEAD LIGHT

Always follow these procedures to verify or replace the head light in order to avoid damaging the carpet beater.

The light is on when the vacuum is on. If the light does not turn on, this means it is burned out and needs to be changed. Follow the steps below to achieve this.

STEP 1 Unscrew the powerhead cover

Disconnect the wand from the electric carpet beater (powerhead).
Turn the electric carpet beater (powerhead) so that the bottom is facing you.
Remove the 7 screws as illustrated above.

STEP 2 Remove the powerhead cover

Turn the electric carpet beater (powerhead) so that the top part is facing you and lift the cover (B) to remove it.

STEP 3 Replace the lightbulb

Remove the old bulb from the socket and replace it with the new one.

STEP 4 Put the carpet beater cover back in place

The wand port must be in the upright position and locked in place.
Put the cover back on top of the electric carpet beater (powerhead).
Turn the carpet beater (powerhead) over.
Replace the screws, as illustrated in step 1.

STEP 5 Screw the power head cover back in place

Replace the 7 screws as illustrated above.

Do not remove the 3 screws in a triangle formation as these hold the motor in place

CLOG IN THE POWER NOZZLE

If the carpet beater (powerhead) gets clogged, use the following procedure to check and clear the blockage.

If the clogging is severe enough, the power nozzle will stop operating.
Once you clear the blockage, press the overload protection reset button (A) and the power nozzle will start working again.

You will find an additional panel at the bottom of the power nozzle (C).
This opening provides a secondary place to check for blockages.

STEP 1 Unscrew the powerhead cover

Disconnect the wand from the electric carpet beater (powerhead).
Turn the electric carpet beater (powerhead) so that the bottom is facing you.
Remove the 7 screws as illustrated above.

STEP 2 Remove the powerhead cover

Turn the electric carpet beater (powerhead) so that the top part is facing you and lift the cover (B) to remove it.

STEP 3 Remove the brush roll cover

To remove the brush roll cover, remove the screws as illustrated above and lift the cover to remove it.

STEP 4 Locate and clean out the blockage

Locate the blockage. Clean the beater brush and remove the dirt that created the clogging.

STEP 5 Replace the brush roll

Hold the opposite end of the brush roll in place.
Push the belt end forward and down while rotating the endplate until it slides into place.
Turn the brush roll to make sure it rotates freely.

STEP 6 Replace the carpet beater (powerhead) cover

The wand port must be in the upright position and locked in place.
Put the cover back on top of the electric carpet beater (powerhead).
Turn the carpet beater (powerhead) over.
Replace the screws, as illustrated in step 1.

STEP 7 Screw the powerhead cover in place

Replace the 7 screws as illustrated above

TROUBLE SHOOTING GUIDE

CHECK THESE FIRST

Service problems that appear to be major can often be solved easily.
You can be your own troubleshooter by reviewing this guide.

Problem

|

Check

|

Solution

---|---|---
Power nozzle won’t turn ON|

Hose power cord
Belt

|

May not be properly connected. Plug hose firmly into receptacle on nozzle.
Belt may be worn or broken. Check and replace if necessary
Switches

|

Make sure surface selector switch and/or brushroll switch are both on
Overload protection reset

|

Make sure the overload protection button has been reset.

Power nozzle still does not operate properly|

Review all the above

|

Contact your dealer for service.

Customer Support

USA:www.myovo.net Canada: www.myovo.ca 1 800 776-7891

TO REGISTER YOUR WARRANTY:
USA: myovo.net/register
Canada: myovo.ca/registrer

TO GET THE PARTS OR OTHER PRODUCTS:
USA: myovo.net
CANADA: myovo.ca
EMAIL AT: info@myovo.net
TOOL FREE: 1-800-776-7891

2044 Autoroute 440 Ouest, Laval, QC, H7S 2M9

Logo

Documents / Resources

| OVO KIT-LV30 Central Vacuum Carpet Deluxe Kit [pdf] User Manual
KIT-LV30 Central Vacuum Carpet Deluxe Kit, KIT-LV30, Central Vacuum Carpet Deluxe Kit, Vacuum Carpet Deluxe Kit, Carpet Deluxe Kit, Deluxe Kit
---|---