Carrier HK Series Control Board Installation Guide
- September 9, 2024
- Carrier
Table of Contents
Carrier HK Series Control Board Installation Guide
NOTE: Read the entire instruction manual before starting the installation.
1. Safety Considerations
Read and follow manufacturer instructions carefully. Follow all local electrical codes during installation. All wiring must conform to local and national electrical codes. Improper wiring or installation may damage the thermostat and equipment.
Recognize safety information. This is the safety-alert symbol . When you see this symbol on the equipment and in the instruction manual, be alert to the potential for personal injury.
Understand the signal words DANGER, WARNING, and CAUTION.
These words are used with the safety-alert symbol. DANGER identifies the most
serious hazards which will result in severe personal injury or death. WARNING
signifies a hazard which could result in personal injury or death. CAUTION is
used to identify unsafe practices which may result in minor personal injury or
product and property damage.
NOTE is used to highlight suggestions which will result in enhanced
installation, reliability, or operation.
This document defines the instructions needed to initiate the relearning process on the ecobee for Carrier/Bryant smart thermostats with InteliSense™ technology whenever one of the following equipment control boards is replaced.
Table 1 – Equipment Boards
NOTE: Please confirm that all the connectors to the control board are fully seated and that all sensors are properly connected.
2. Relearn Process
To initiate the relearning process, follow the steps below.
NOTE: The screens provided are for a 2-stage furnace control board, but the
steps apply to all boards listed in Table 1.
2.1. ecobee3 lite
(SKUs EB-STATE3LTICR-01, EB-STATE3LTICB-01, EB-STATELTIBR-01, EB-
STATE3LTIBB-01)
1. From the Home screen, press the hamburger menu, to transition to the Main
Menu System screen.
Fig. 1 – Home Screen
2. From the Main Menu System screen, press the settings button which will launch the Main Menu General screen.
Fig. 2 – Main Menu System Screen
3. From the Main Menu General screen, select the Settings option to launch the Settings screen.
Fig. 3 – Main Menu General Screen
4. From the Settings screen, press the Installation Settings option.
Fig. 4 – Settings Screen
5. From this Installation Settings screen, press the Equipment option
Fig. 5 – Installation Settings Screen
6. From the Equipment screen, press the Reconfigure Equipment option and
follow the steps to define the equipment configuration.
After completing these steps, return to the Home screen to begin the steps to
learn the outdoor unit (if applicable).
Fig. 6 – Equipment Screen
7. To continue the process, from the Home Screen, press the hamburger menu to transition to the Main Menu System screen.
Fig. 7 – Home Screen
8. From the Main Menu System screen, press the Settings button which will launch the Main Menu General screen.
Fig. 8 – Main Menu System Screen
9. From the Main Menu General screen, select the Settings option to launch the Settings screen.
Fig. 9 – Main Menu General Screen
10. From the Settings screen, press the Installation Settings option.
Fig. 10 – System Screen
11. From the Installation Settings screen, press the Test Equipment option. When the Warning screen is displayed, press OK.
Fig. 11 – Test Equipment Option Screen
Fig. 12 – Test Equipment Screen
12. Based on the type of outdoor equipment installed, select the option that will engage the Y1 signal to turn on the outdoor unit’s compressor. Run the test for approximately 10 seconds and then turn Off. Return to the Home screen to confirm the equipment has been relearned.
Fig. 13 – Test Equipment Selector Screen
13. To confirm the relearn process was successful, from the Home screen, press the hamburger menu, to transition to the Main Menu System screen.
Fig. 14 – Home Screen
14. From the Main Menu System screen, press the Settings button which will launch the Main Menu General screen.
Fig. 15 – Main Menu System Screen
15. From the Main Menu General screen, select the System option.
Fig. 16 – Main Menu General Screen
16. From the System screen, select the Equipment option.
Fig. 17 – System Screen
17. The learned equipment will be displayed on the screen. Completing these steps will ensure equipment data is reported to the InteliSense cloud.
Fig. 18 – Equipment Screen
2.2. ecobee Premium
(SKUs EB-STATE6ICR-01, EB-STATE6IBR-01)
1. From the home screen, press the hamburger menu, to transition to the Main
Menu System screen.
Fig. 19 – Home Screen
2. From the Main Menu System screen, press the Settings button which will launch the Main Menu General screen.
Fig. 20 – Main Menu System Screen
3. From the Main Menu General screen, select the Settings option to launch the Settings screen.
Fig. 21 – Main Menu General Screen
4. From the Settings screen, select the Installation Settings option.
Fig. 22 – Settings Screen
5. From this Installation Settings screen, select the Equipment option.
Fig. 23 – Installation Settings Screen
6. From the Equipment screen, press the Reconfigure Equipment option and follow the steps to define the equipment configuration. After completing these steps, return to the Home screen to begin the steps to learn the outdoor unit (if applicable).
Fig. 24 – Equipment Screen
7. To continue the process, from the Home Screen, press the hamburger menu to transition to the Main Menu System screen.
Fig. 25 – Home Scree n
8. From the Main Menu System screen, press the Settings button which will launch the Main Menu General screen.
Fig. 26 – Main Menu System Screen
9. From the Main Menu General screen, select the Settings option to launch the Settings screen.
Fig. 27 – Main Menu General Screen
10. From the Settings screen, press the Installation Settings option.
Fig. 28 – Settings Screen
11. From the Installation Settings screen, press the Test Equipment option. When the Warning screen is displayed, press OK.
Fig. 29 – Test Equipment Screen
Fig. 30 – Test Equipment Screen
12. Based on the type of outdoor equipment installed, select the option that will engage the Y1 signal to turn on the outdoor unit’s compressor. Run the test for approximately 10 seconds and then turn Off. Return to the Home screen to confirm the equipment has been relearned.
Fig. 31 – Test Equipment Selector Screen
13. To confirm the relearn process was successful, from the Home screen, press the hamburger menu, to transition to the Main Menu System screen.
Fig. 32 – Home Screen
14. From the Main Menu System screen, press the Settings button which will launch the Main Menu General screen.
Fig. 33 – Main Menu System Screen
15. From the Main Menu General screen, select the System option.
Fig. 34 – Main Menu General Screen
16. From the System screen, select the Equipment option.
Fig. 35 – System Screen
17. The learned equipment will be displayed on the screen. Completing these steps will ensure equipment data is reported to the InteliSense cloud.
Fig. 36 – Equipment Screen
© 2024 Carrier. All rights reserved.
A Proud Member of the Carrier Family
Catalog No: IM-HK-03
Edition Date: 07/24 Replaces: IM-HK-02
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>