naztech AURA360 Wireless ANC Headphones User Manual

: September 6, 2024
: naztech

Table of Contents

naztech AURA360 Wireless ANC Headphones
Frequently Asked Questions
OVERVIEW
SPECIFICATIONS
GETTING STARTED
BLUETOOTH CONNECTION SETUP
CONTROLS
LISTENING MODES
TROUBLESHOOTING
SAFETY INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

naztech AURA360 Wireless ANC Headphones

Frequently Asked Questions

Q: How do I know if the external ANC microphones are working?

A: To test the functionality of the external ANC microphones, enable the ANC feature on your headphones and observe a significant reduction in ambient noise when the microphones are properly positioned near your ears.

Q: Can I use both types of microphones simultaneously?

A: The Naztech XYZ headphones are designed to allow you to use either the built-in vocal microphones or the external ANC microphones at a time, not both simultaneously.

OVERVIEW

SPECIFICATIONS

Bluetooth Version 5.3
Connection Range Up to 33 ft (10 meters)
Carrying Pouch
Driver Size 40 mm each
Frequency Range 20 Hz to 20 kHz
ANC Rating -30 dB
Power Input 5v?1A
Battery Capacity 500 mAh
Playtime Up to 24 hours (ANC On)
Up to 30 hours (ANC Off)
Charging Time 2 hours

Package Contents:

Aura 360 ANC
Wireless Headphones
USB-C Charging Cable
3.5mm Aux Cable
User Manual

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HyperGear is under license. Other trademarks and trade names are those of their respective owners.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

GETTING STARTED

Read all safety instructions and warnings prior to using these products. See the end of this manual for detailed information.

Charging Your Headphones

NOTE: Fully charge your headphones before first use.
Using the included USB-C charging cable, connect the headphones to a USB power source.
The Status LED will glow while they charge .

Charging
Fully Charged (approximately 2 hours)

BLUETOOTH CONNECTION SETUP

Pairing with Your Device

Hold the Multifunction Button for 3 seconds to power the headphones on. They will automatically enter Bluetooth pairing mode, and the Status LED will blink BLUE and RED to indicate that they are ready to pair.
Open the Bluetooth menu on your phone, tablet, or computer. Enable searching for available devices.
Select “Naztech AURA 360” to pair your headphones with your device.
Once connected, the Status LED will blink BLUE while the headphones are in use.

Your headphones will automatically reconnect to your device the next time you turn your headphones on.
NOTE: Your headphones must remain within 33 feet (10 meters) of your device, or the Bluetooth wireless connection will be lost.

Pairing with a Second Device
With Multipoint Connection technology, you can pair your headphones with two devices at once.

After pairing with Device A, press and hold the Multifunction Button for 3 seconds to power the headphones off. Then, turn off Device A’s Bluetooth function. See your device’s user manual for detailed information.
Power the headphones on again. Follow the normal pairing instructions to pair them with Device B.
Once Device B is paired and successfully connected, turn on Device A’s Bluetooth function. Open Device A’s Bluetooth menu and select the headphones to connect.

NOTE: Your headphones can only play audio from one device at a time, even if two are connected. The headphones will automatically switch to whichever device is currently playing audio. If you wish to pair your headphones to a different phone, tablet, or computer, find them in your device’s Bluetooth menu and select “Forget This Device” or “Unpair”.

CONTROLS

LISTENING MODES

Active Noise Cancelling
A quad-mic monitoring array “listens” to sounds both outside and inside each ear cup. The ANC chipset then generates inverted anti-noise soundwaves that neutralize the background sounds. The adaptive technology adjusts the level of noise cancelling to match the ambient loudness of your environment.
Ambient Transparency
In Ambient Transparency mode, the ANC system picks up environmental sounds, amplifies them, and plays them over your audio. It’s perfect for staying aware of your surroundings and effortlessly engaging in conversation without having to remove your headphones or pause your music.
TIP: You can also use ANC mode without playing any audio if you just want some peace and quiet. In order to save your battery life, remember to turn off your headphones when you’re done using them.
ANC Off
Also known as Passive Noise Cancellation mode, ANC Off extends the headphones’ battery life while also letting the comfort features do the heavy lifting. The over-the-ear fit and low-pressure ear cushions create a noise-isolating circumaural seal that substantially prevents outside noise from entering in.
Aux In
No Bluetooth? No battery? No problem! Plugging into the 3.5mm auxiliary port activates Aux In mode, which allows for uncompressed analog audio playback without needing battery.

NOTE: When plugged in, Bluetooth wireless streaming functions, ANC functions, and on-ear buttons are automatically disabled. Use the media controls on your audio source device instead.

TROUBLESHOOTING

If your headphones will not turn on:
They may be out of power. Connect them to a power source and fully recharge.
If your headphones will not pair with your device:
- Check that your headphones are in pairing mode. If not, power them OFF and back ON again. Then, follow the normal pairing instructions.
- Your device may be out of connection range. Try pairing while your headphones are within 3 feet of your device.
- Your device’s battery and/or your headphones’ battery level may be too low. Fully recharge both your device and your headphones before trying again.
- Perform a Bluetooth connection SOFT reset – see next page.
If your headphones are successfully paired and connected, but there is no sound:
- The volume on your source device may be muted. Make sure your device is playing at audible levels.
- Perform a Bluetooth connection SOFT reset – see next page.
- Perform a Bluetooth connection HARD reset – see next page.
If the sound is too low / too high / poor quality:
- Adjust the volume level on your audio source device. NOTE: some apps and programs have their own sound settings separate from the general device settings. Make sure to adjust those as well, as needed.
- Move away from or turn off nearby devices that may be generating interference, such as another Bluetooth device or a wireless router.
- Try turning off your device’s Wi-Fi to improve audio quality.
- Closing non-essential applications on your device may improve audio quality. Running multiple applications can reduce the amount of internal resources available to transmit audio clearly.

Perform a Bluetooth connection SOFT reset; AKA – The Off-and-On Maneuver

Access your device’s Bluetooth menu.
Turn OFF your device’s Bluetooth functionality.
Power OFF your headphones.
Turn your device’s Bluetooth functionality back ON.
Power your headphones back ON.

Perform a Bluetooth connection HARD reset; AKA – The Unpair/Re-Pair Technique:

Access your device’s Bluetooth menu.
Locate your headphones and tap the icon to access their options. NOTE: icon location may vary by device and OS version.
Unpair the headphones from your device by selecting “Forget This Device” or “Unpair”.
Power your headphones ON, and pair them with your device as usual.

SAFETY INSTRUCTIONS

Read all safety instructions and warnings prior to using this product. Improper use and failure to follow safety guidelines could result in damage, excess heat, toxic fumes, fire, explosion, electrical shock, or other hazards causing serious and/or fatal injury and/or property damage that is not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.

Permanent hearing loss may occur if you listen at high volumes. Set the volume to a safe level.
Maintain volume levels that will allow you to hear sound around you and be alerted to potentially hazardous situations.
This product is not waterproof. Do not submerge or expose to corrosive materials. Do not clean with harsh chemicals, soaps, or detergents.
Recharge the headphones with the included USB-C charging cable and a 5W USB charger. More powerful chargers are not necessary for this unit and may damage/overheat the battery or cause a fire hazard.
Do not store in a depleted state. Battery cells may be damaged. Charge your headphones at least once every 3 months even when not in use.
Do not store at extreme temperatures (below 40 °For above 90 °F). Battery cells may be damaged.
Do not attempt to modify, disassemble, or repair this product.
Avoid excessive drops, bumps, and abrasions.
If the device has dents, punctures, tears, deformities, or corrosion, discontinue use and contact the manufacturer or dispose of in an appropriate method.
lf you find this product rapidly increasing in temperature, emitting odor, deformed, abraded, or demonstrating an abnormal phenomenon, discontinue use immediately.
Do not use in the vicinity of flammable liquids or gases, propane tanks, large engines, highvoltage devices, or heat sources such as radiators and ovens.
Disposal of the unit in the garbage is unlawful under state and federal environmental laws and regulations.