naztech 15425 Smart Grip Wireless Charging Car Mount User Manual
- June 6, 2024
- naztech
Table of Contents
naztech 15425 Smart Grip Wireless Charging Car Mount User Manual
SAFETY INSTRUCTIONS
Read all safety instructions and warnings prior to using this product. Improper use and failure to follow safety guidelines could result in hazards, injury and/or property damage that is not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.
- Use only the included adapter to power this device. Standard adapters may damage the charger or cause a fire hazard.
- Do not place metal objects, magnets, magnetic stripe cards, and hard drive based devices near the wireless charger. It may cause data corruption.
- Do not attempt to modify, disassemble, or repair this product.
- Do not expose to water, moisture, or extreme temperatures (below 40°F or above 90°F).
- Under any circumstances, if you find this product rapidly increasing in temperature, emitting odor, or demonstrating an abnormal phenomenon, discontinue use immediately.
NOTE: This charger is designed for 0i-compatible devices. If your phone does not have built-in Qi wireless charging capabilities please use a certified Qi wireless charging case or receiver. Refer to your phone’s user manual for detailed features and functions.
- NO Metal
- NO Magnets
- NO Thick Case
Phone cases that contain metal, magnets, or are thicker than 3mm will interfere with wireless charging.
Product Overview
-
Automatic Grips
-
Charging Surface
-
Touch Sensor Pad
-
Release Button
-
LED Indicators
-
Extendable Foot
-
Locking Ring
-
Cooling Vents
-
Backup Battery
-
USB-C Input
NOTE: The internal battery lets you open the grip 2-3 times after the car is shut off for added convenience. -
360° Ball
-
Telescopic Neck
-
Telescopic Knob
-
Pivot Knob
-
2-Step Locking Lever
-
Powerful Suction
-
360° Ball
-
Button
-
Air Vent Clip
-
Air Vent Support
SPECIFICATIONS
WIRELESS CHARGER CRADLE
Input: 9V Fast Charge
Output: 15W/10W/7.5W/5W
**FAST CAR CHARGER
**
Input: 12V-24V
Output: Wireless Charger USB 5V/3A, 9V/2A,12V/1.5A USB 5V/2.4A
USB-C CHARGING CABLE
NOTE: Fast Charge mode requires use of the included fast charger and cable. Standard 1A/2A adapters and USB-C cables are not powerful enough for this charger and may cause it to malfunction or overheat.
ASSEMBLY
Place the locking ring over the 360° ball. Firmly press the mount head onto
the ball. Pivot to your desired viewing angle then twist the ring until it’s
secured.
INSTALLATION INSTRUCTIONS
VENT
Squeeze the button on the base. Firmly slide the mount onto the air vent. Release the button once it’s secure.
DASHBOARD/ WINDSHIELD
Remove the protective liner from the suction. Position as desired. Push down the locking lever twice to secure the mount.
NOTE: If needed, rinse the suction cup with water and air-dry to restore stickiness.
Connect the wireless charger to the TOP/BLUE USB port on the car adapter.
IMPORTANT: PLUG INTO TOP USB PORT
Place your phone onto the charger. The arms will close automatically. Your
phone will indicate when charging begins.
ADVANCED DUAL MODE BUTTONS
Touch the sensor on the left or Push the button on the right to open and close
the arms as needed.
FOR LARGE PHONES
- Pull down firmly to extend the foot completely.
- Adjust to the height needed to center your phone on the charging area. Your phone will indicate charging when it is positioned correctly.
LED STATUS
- Standby
- Charging
- Foreign Object Detected
If the LED is flashing, remove any foreign objects that may affect charging
(such as metal plates and other objects) from the charging area.
Its normal for a wireless charger and your device to become warm while charging.
CUSTOMER SUPPORT
Need help? Visit www.naztech.com for additional product information or contact info@naztech.com
Contact info@naztech.com to submit a warranty claim. Proof of purchase is required.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>