Godox V1PROS TTL Li-ion Round Head Camera Flash Instruction Manual

• Press the camera shutter halfway to focus. The aperture value and effective flash range will be displayed in the LCD panel.
• When the shutter is fully pressed, the flash will fire a pre-flash that the camera will use to calculate exposure and flash output the instant before the photo is taken.

FEC (Flash Exposure Compensation)

With FEC function, this flash can adjust from -3 to +3 with 1/3 increment each step. It is useful in situations where minor adjustment of the TTL system is needed based on the environment.

Setting FEC Amount

1. Press the <+/-> button, FEC amount will be highlighted on the LCD panel.

2. Turn the select dial to set the FEC amount.”0.3″means 1/3 step, “0.7”means 2/3 step. To cancel the FEC, set the amount to “0”.

3. Press set button again to confirm the setting.

High-Speed Sync

High speed sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits.

1. Press function button 2 so that the < > icon is displayed on the LCD panel.

2. Check whether the < > icon is displayed in the viewfinder.

Note:

1. If you set a shutter speed that is the same as or slower than the camera’s maximum flash sync speed, < > will not be displayed in the viewfinder.
2. With high-speed sync, the faster the shutter speed, the shorter the effective flash range.
3. To return to normal flash, press button again. Then < > will disappear.
4. Multi flash mode cannot be set in high-speed sync mode.
5. Over-temperature protection may be activated after 60 consecutive high-speed sync flashes.

Second-Curtain Sync

With a slow shutter speed and second-curtain sync, you can create a light train following the subject. The flash fires right before the shutter closes.

Choose REAR flash mode in Sony camera setting.

Flash Mode — M: Manual Flash

The flash output is adjustable from 1/1 full power to 1/256 power with 1/10 increment each step. To obtain a correct flash exposure, use a hand-held flash meter to determine the required flash output.

1. Press mode button so that is displayed on the LCD panel.

2 Press the <+/-> button to select flash output amount, then turn the select dial to adjust it. Press the set button again to confirm the setting.

S1 Optic Control Unit Setting

In M manual flash mode, press <S1/S2> button so that this flash can function as an optic S1 secondary flash with optic sensor. With this function, the flash will fire synchronously when the main flash fires, the same effect as that by the use of wireless triggers. This helps create multiple lighting effects.

S2 Optic Control Unit Setting

In M manual flash mode, press <S1/S2> button so that this flash can also function as an optic S2 secondary flash with optic sensor. This is useful when cameras have pre-flash function. With this function, the flash will ignore a single “pre-flash” from the main flash and will only fire in response to the second, actual flash from the main flash.

Note:

1. S1 and S2 optic control triggering is only available in M manual flash mode.
2. Press function 3 button <S1/S2> to switch between S1/S2 optic control or turn off this function.

Flash Mode — Multi: Stroboscopic Flash

With slow shutter speed in multi flash mode, a rapid series of flashes is fired. It can be used to capture multiple images of a moving subject in a single photograph.

You can set the flash frequency (number of flashes per sec. expressed as Hz), the number of flashes, and the flash output.

1. Press mode button so that is displayed on the LCD panel.

2. Press the function button 2 to select the number of flashes. Turn the select dial to set the number, then press it to confirm the settings. Press the function button 3 to select the flash frequency. Turn the select dial to set the frequency, then press it to confirm the settings.

3. Press <+/-> button to select flash output amount. Turn the select dial to set the amount, then press it to confirm the settings.
Flash output range: 1/256-1/4.

Calculating the Shutter Speed

During multi flash, the shutter remains open until the firing stops. Use the formula below to calculate the shutter speed and set it with the camera.

Number of Flashes / Flash Frequency = Shutter Speed

For example, if the number of flashes is 10 and the flash frequency is 5Hz, the shutter speed should be at least 2 seconds.

To avoid overheating and deteriorating the flash head, do not use multi flash more than 10 times in succession. After 10 times, allow the camera flash to rest for at least 15 minutes. If you try to use the multi flash more than 10 times in succession, the firing might stop automatically to protect the flash head. If this happens, allow at least 15 minutes’ rest for the camera flash.

Note:

1. Multi flash is most effective with a highly reflective subject against a dark background.
2. Using a tripod and TTL flash trigger XPROII is recommended.
3. A flash output of 1/1 and 1/2 cannot be set for multi flash.
4. Multi flash can also be used with “buLb” mode.
5. Multi flash mode cannot be set in high-speed sync mode.
6. If the number of flashes is displayed as “–“, the firing will continue until the shutter closes or the battery is exhausted. The number of flashes will be limited as shown by the following table.

Maximum Time of Consecutive Flashes

Hz

Flash output

|

1

| 2| 3| 4| 5
---|---|---|---|---|---
1/4| 8| 6| 4| 3|

3

1/8

| 14| 14| 12| 10|

8

1/16

| 30| 30| 30| 20| 20
1/32| 60| 60| 60| 50|

50

1/64

| 90| 90| 90| 80| 80
1/128| 90| 90| 90| 90|

90

1/256

| 90| 90| 90| 90|

90

Hz

Flash output

|

6-7

| 8-9| 10| 20-50| 60-100
---|---|---|---|---|---
1/4| 2| 2| 2| 2|

2

1/8

| 6| 5| 4| 4| 4
1/16| 20| 10| 8| 8|

8

1/32

| 40| 30| 20| 16| 12
1/64| 70| 60| 50| 30|

20

1/128

| 90| 80| 70| 40| 40
1/256| 90| 80| 70| 40|

40

Wireless Flash Shooting: 2.4G Wireless Transmission

This section explains wireless transmitting/receiving flash shooting.

The V1Pro S attached to the camera is referred as the transmitter unit, while a V1Pro S that is wirelessly controlled is referred as the receiver unit.

You can also wirelessly control the V1Pro S set as the receiver unit with the TTL flash trigger XPROII (sold separately). For details on setting the flash trigger functions, see the its instruction manual.

Using a flash with a radio transmission wireless shooting function make it easy to shoot with advanced wireless multiple flash shooting, in the same way as TTL auto flash shooting.

As long as the channel, group, ID, and other relevant wireless settings of the transmitter and receiver units are set to the same, the settings on the V1Pro S (transmitter unit) will be automatically applied to the wirelessly controlled V1Pro S (receiver unit). Therefore, there is no need to operate the receiver unit during shooting.

Positioning and Operation Range (Example of wireless flash shooting)

• Auto Flash Shooting with One Receiver Unit

1. RECEIVER
2. TRANSMITTER
3. Transmission distance is about 100m

Note:

1. Before shooting, perform a test flash and test shooting.
2. The transmission distance might be shorter depending on the conditions such as positioning of receiver units, the surrounding environment and whether conditions.

Auto Flash Shooting with Multiple Receiver Groups

You can divide the receiver units into two or three groups and perform TTL auto flash while changing the flash ratio (flash output ratio). In addition, you can set and shoot with a different flash mode for each firing group, for up to 4 groups.

• Auto Flash Shooting with Two Receiver Groups

• Auto Flash Shooting with Three Receiver Groups

Wireless Settings

You can switch between normal flash and wireless flash. For normal flash shooting, be sure to set the wireless setting to “OFF”, and the < > won’t be displayed on the LCD panel.

Setting the Flash as A Transmitter Unit

Press < > button so that < > is displayed on the LCD panel, but the < > won’t be displayed.

Setting the Flash as A Receiver Unit

Press < > button so that < > and< > are displayed on the LCD panel.

Setting the Transmitter Unit Flash Mode

1. Press the < > wireless button to make < >is displayed on the panel while <

is not displayed. Press the function button 1 to select –/TTL/M. Choose one of them as the flash mode of the transmitter unit.

2. Press button to switch to Multi mode.

Wireless Channel Settings

If there are other wireless flash systems nearby, you can change the wireless channels to prevent signal interference. The wireless channels of the transmitter unit and the receiver unit(s) must be set to the same.

1. Press < MENU > menu button to enter menu setting. Turn the select dial to , then press the set button to choose CH.

2. Turn the select dial to adjust wireless channel from 01 to 32. Press the set button to confirm.

ID Settings

Change the wireless channels and wireless ID to avoid interference for it can only be triggered after the wireless channels and IDs of the transmitter unit and the receiver unit are set to the same. Press the menu button to enter C.Fn ID, press the set button to choose OFF to turn off the wireless ID, or choose any figure from 01 to 99.

1. Press < MENU > menu button to enter menu setting. Turn the select dial to , then press the set button to choose ID.

2. Turn the select dial to adjust wireless ID from 01 to 99 or OFF. Press the set button to confirm.

Scan the Spare Channel

You can scan the spare channel to avoid the interference of using the same channel by others.

1. Press < MENU > menu button to enter menu setting. Turn the select dial to < SCAN >, then press the set button to choose SCAN.

2. Turn the select dial to choose START, then press the set button to scan. And the 8 spare channels will be displayed for your choice.

TTL: Fully Automatic Wireless Flash Shooting

Using Automatic Wireless Flash with a Single Receiver Unit

1. Transmitter Unit Setting

Press the wireless button and the < > icon is displayed on the LCD panel, then the V1Pro S attached to the camera is set as the transmitter unit.

Set the V1Pro S mounted on the camera as a transmitter unit, then M/ A/B/C group can be set as TTL mode separately.

2. Receiver Unit Setting

Press the wireless button and the is displayed on the LCD panel, then the V1Pro S wirelessly controlled is set as the receiver unit A/B/C/D/E.

3. Check the Communication Channel

Set the wireless channels of transmitter unit and receiver unit to the same. For example, if the transmitter unit channel is set to 01, then the receiver unit channel needs to be 01 as well.

4. Position the Camera and Flashes

The transmission distance of the transmitter unit and receiver unit is about 100m.

1. RECEIVER
2. TRANSMITTER
3. Transmission distance is about 100m

5. Check Whether the Flash is Ready

Check whether the transmitter unit’s flash ready indicator is lightened. When the receiver unit’s flash is ready, the AF-assist beam lighting area will blinks at 1 second intervals.

6. Check the Flash Operation

Press the transmitter unit’s test button < >. Then, the receiver unit will fire. If not, adjust the distance from the transmitter unit.

Using Automatic Wireless Flash with Multiple Receiver Units

When stronger flash output or more convenient lighting operation is needed, increase the number of receiver units and set it as a single receiver unit. To add receiver units, use the same steps as setting “using automatic wireless flash with a single receiver unit”. Any flash group can be set (A/B/C/D/E).

When the number of receiver units is increased or the transmitter unit flash firing is ON, automatic control is implemented to make all groups of flashes fire the same flash output and ensure the total flash output is up to standard exposure.

Note:

1. If the receiver unit’s auto power off function is on, press the transmitter unit’s test button to power it on. Please note that test firing is unavailable during the camera’s regular metering time.
2. By pressing the menu button to enter C.Fn setting, the effective time of receiver unit’s auto power off is changeable between 60min or 30min (RX STBY).

Using Fully Automatic Wireless Flash

The FEC and other settings that set on the transmitter unit will also be appeared on the receiver unit automatically. The receiver unit does not need any operation. Use the following settings to make wireless flash shooting according to the same methods with normal flash shooting.

• Flash Exposure Compensation

About Transmitter Unit

Use two or more transmitter units. By preparing several cameras that with transmitter units attached, cameras can be changed in shooting while keeping the same lighting source (receiver unit).

M: Wireless Flash Shooting with Manual Flash

Using wireless (multiple flash) shooting with manual flash, you can shoot with a different flash output setting for each receiver unit (flash group) while setting all parameters on the transmitter unit.

1. Set the Transmitter Unit’s Flash Group to

Press the wireless button and the < > icon is displayed on the LCD panel, then the V1Pro S attached to the camera is set as the transmitter unit. Press the corresponding function button 1/2/3/4<M/A/B/C > to make is displayed in all the flash groups on the LCD panel.

2. Set the Flash Output of Each Flash Group

Press function button <M/A/B/C > to choose a group. Turn the select dial to set the flash output of the group, then press the set button to confirm.

3. Set the Wireless Channels of Transmitter Unit and Receiver Unit to the Same

For example, if the transmitter unit channel is set to 01, then the receiver unit channel needs to be 01 as well.

4. Take Picture

Each receiver unit fires at the set flash ratio.

Multi: Wireless Flash Shooting with Manual Flash

1. Set the Transmitter Unit to Wireless Multi Flash

Press mode button so that is displayed on the LCD display, then press the wireless button so that and < > are displayed on the LCD display at the same time.

2. Set the Flash Output, Number of Flashes and Flash Frequency of the Wireless Multi Flash

Press <+/-> button to select flash output of multi flash. Turn the select dial to set the flash output amount, then press the set button to confirm the settings and exit. Press the set button to select number of flashes of flash frequency. Turn the select dial to set the number of flashes of flash frequency, then press the set button to confirm the settings and exit.

3. Turn On/Off the Wireless Multi Flash of Receiver Unit Group

The wireless multi flash of receiver unit A/B/C can be turned on or off directly on the transmitter unit.

4. Set the Receiver Unit

Press the wireless button to make the and are displayed on the LCD panel of the receiver unit.

5. Set the Wireless Channels of Transmitter Unit and Receiver Unit to the Same

For example, if the transmitter unit channel is set to 01, then the receiver unit channel needs to be 01 as well.

Note: The parameters of receiver unit can be directly set on the transmitter unit on the condition that channels and IDs of them are set to the same.

TTL/M Mode Switch Function

1. Toggle the TTL/M mode toggle switch in non-wireless mode can switch flash mode.
2. TCM switch function is workable by default when switched to M manual mode from TTL mode.

Screen Lock

Press and hold the < > button for 2s can lock or unlock the screen, “LOCKED” is displayed on the LCD panel when the screen is locked.

Mode Lock

Press and hold the button to make the < > is displayed on the panel, the current flash mode (TTL/M/RPT flash mode) is locked, press and hold again to unlock, then the flash mode can be switched by pressing the button.

The Reason & Solution of Not Triggering in Godox 2.4G Wireless

1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base station, 2.4G wifi router, Bluetooth, etc.)
→ To adjust the channel CH setting on the flash trigger (add 10+ channels) and use the channel which is not disturbed. Or turn off the other 2.4G equipment in working.

2. Please make sure that whether the flash has finished its recycle or caught up with the continuous shooting speed or not (the flash ready indicator is lightened) and the flash is not under the state of over-heat protection or other abnormal situations.
→ Please downgrade the flash power output. If the flash is in TTL mode, please try to change it to M mode (a pre-flash is needed in TTL mode).

3. Whether the distance between the flash trigger and the flash is too close or not ( < 0.5m).
→ Please turn on the “close distance wireless mode”:
X1 Series: Press and hold the triggering button then turn on the device until the indicator blinks twice.
Xpro and X2T Series: Set the C.Fn-DIST to 0-30m.
X nano: Set the trigger distance to 0-30m.

4. Whether the flash trigger and the receiver end equipment are in the low battery states or not
→ Please replace the battery.

Other Applications

Sync Triggering

The sync cord jack is a 2.5mm plug. Insert a trigger plug here and the flash will be fired synchronously with the camera shutter.

Modeling Flash

If the camera has a depth-of-field preview button, pressing it will fire the flash continuously for 1 second. This is called modeling flash. It enables you to see the shadow effects on the subject and the lighting balance. You can fire the modeling flash during wireless or normal flash shooting.

Note: To avoid overheating and deteriorating the flash head, do not fire the modeling flash for more than 10 consecutive times. If you fire the modeling flash 10 consecutive times, allow at least 10 minutes’ break for the camera flash.

Auto Focus Assist Beam

In poorly-lit or low-contrast shooting environments, the built-in auto focus assist beam will automatically light on to make it easier for auto focus. The beam will light up only when auto focus is difficult and get out as soon as the auto focus becomes correct.

If you want to turn off the auto focus assist beam, set the “AF” to “OFF” in the C.Fn settings.

Note: If you find the auto focus assist beam does not light up, this is because the camera has got a correct auto focus.

Position

| Effective Range
---|---
Center|

0.6~10m / 2.0~32.8 feet

Periphery

|

0.6~5m / 2.0~16.4 feet

Bounce Flash

By pointing the flash head toward a wall or ceiling, the flash will bounce off the surface before illuminating the subject. This can soften shadows behind the subject for a more natural-looking shot. This is called bounce flash.

To set the bounce direction, hold the flash head and turn it to a satisfying angle.

Note:

1. If the wall or ceiling is too far away, the bounced flash might be too weak and result in underexposure.
2. The wall or ceiling should be a plain, white color for high reflectance. If the bounce surface is not white, a color cast may appear in the picture.

ZOOM: Setting the Flash Coverage

The flash coverage can be set automatically or manually. It can be set to match the lens focal length from 28mm to 105mm. In auto zoom mode, the focal length changes in response to the camera’s zoom lens to provide optimal flash results.

In manual zoom mode, press the button.

• Turn the select dial to change the flash coverage.
• If < > is displayed, the flash coverage will be set automatically.

Note: If you set the flash coverage manually, make sure it covers the lens focal length so that the picture will not have a dark periphery.

Low Battery Warning

If the battery power is low, < > will appear and blink on the LCD panel. Please replace the battery immediately.

C.Fn: Setting Custom Functions

Press the menu button to enter C.Fn settings.

Custom Function Signs| Function| Options| Settings & Description
---|---|---|---
m/ft| Distance indicator| m| m
ft| Feet
AF| AF-assist beam| ON| ON
OFF| OFF
STBY| Auto sleep setting| ON| ON
OFF| OFF
RX STBY| Receiver auto power off timer| 60min| Power off automatically after 60 minutes of idle use when the flash is set as a receiver unit.
30min| Power off automatically after 30 minutes of idle use when the flash is set as a receiver unit.
SCAN| Scan the spare channel| OFF| OFF
START| Start to scan the spare channel
CH| Wireless Channel| 01-32| Choose channels from 01-32
ID| ID| OFF| OFF
01-99| Choose any figure from 01-99
BEEP| Beeper| ON| ON
OFF| OFF
LIGHT| Backlighting time| 12sec| Off in 12 sec.
OFF| Always off
ON| Always lighting
LCD| LCD contrast ratio| -3~+3| 7 levels

Note:

1. The “Verx.x” in the top-right corner refers to the software version.
2. Turn the select dial to select the custom function No. and its parameters.
3. Press set button to select the custom function No. and confirm its setting.
4. After you set the custom function and press menu button, the camera will be ready to shoot.
5. Press and hold the function button 1 in the MENU interface until “OK” is displayed on the panel, which means the parameters in C.Fn are reset.

Protection Function

Over-Temperature Protection

• To avoid overheating and deteriorating the flash head, do not fire more than 100 continuous flashes in fast succession at 1/1 full power. After 100 continuous flashes, allow a rest time of at least 10 minutes.
• If you fire more than 100 continuous flashes and then fire more flashes in short intervals, the inner over-temperature protection function may be activated and make the recycle time over 10 seconds. If this occurs, allow a rest time of about 10 minutes, and the flash unit will then return to normal.
• When the over-temperature protection is started, <> is shown on the LCD display.

Number of flashes that will activate over-temperature protection:

Note: Numbers of flashes of over-temperature protection are different in different zoom values and different levels.

Number of flashes that will activate over-temperature protection in HSS mode:

Technical Data

• Auto zoom (flash coverage is set automatically to match the lens focal length and image size)

• Manual zoom

• Swinging/tilting flash head (bounce flash): 0 to 330° horizontally and -7° to 120° vertically

Flash Duration| 1/300 to 1/20000 seconds
Exposure Control
Exposure Control System| TTL auto flash and manual flash
Flash Exposure Compensation (FEC)| Manual: ±3 steps with 1/3 increment each step
Sync Mode| High-speed sync (up to 1/8000 seconds), first-curtain sync, and second-curtain sync
Multi Flash| Provided (up to 90 times, 100Hz)
Wireless Flash (Radio 2.4G Transmission)
Wireless Function| Transmitter, Receiver, Off
Transmitter Unit Groups| M, A, B, C
Controllable Receiver Groups| A, B, C, D, E (E group can be controlled by X series flash trigger)
Transmission Range (approx.)| 100m
Channels| 32 (01~32)
ID| OFF/01~99
Modeling Flash| Fired with camera’s depth-of-field preview button
Auto Focus Assist Beam
Effective Range (approx.)| Center: 0.6~10m / 2.0~32.8 feet
Periphery: 0.6~5m / 2.0~16.4 feet
LED Modeling Lamp
Power| 2w
Color Temperature| 3300K±200K
Power Supply
Built-in Lithium Battery| 7.2V/2980mAh
Recycle Time| Approx. 1.3 seconds. Green LED indicator will light up when the flash is ready.
Number of Flashes at 1/1 step| Approx. 500
Power Saving| Power off automatically after approx. 90s of idle use when set as a transmitter unit.
Screen sleep automatically after approx. 60min (or 30min) of idle use when set as a receiver unit.
Sync Triggering Mode| Hot shoe, 2.5mm sync cord
Dimension
W x H x D| 6.14‘’×2.99‘’×4.88‘’
Net Weight Without Battery| 466g
Net Weight With Battery| 580g

Specifications and data may subject to changes without notice.

Troubleshooting

If there is a problem, refer to this troubleshooting guide.

The camera flash does not fire.

• The camera flash is not attached securely to the camera.
  Attach the camera’s mounting foot securely to the camera.

• The electrical contacts of the camera flash and camera are dirty.
  → Clean the contacts.

The power turns off by itself.

• After 90 seconds of idle operation, auto power off took effect if the flash is set as a transmitter unit.
  → Press the shutter button halfway or press any flash button to wake up.

• After 60 minutes (or 30 minutes) of idle operation, the flash enter sleep mode if it is set as receiver unit.
  → Press any flash button to wake up.

Auto zoom does not work.

• The camera flash is not attached securely to the camera.
  → Attach the camera flash’s mounting foot to the camera.

The flash exposure is underexposed or overexposed.

• You used high-speed sync.
  → With high-speed sync, the effective flash range will be shorter. Make sure the subject is within the effective flash range displayed.

• You used manual flash mode.
  → Set the flash mode to TTL or modify the flash output.

Photos have dark corners or only parts of the target subject are illuminated.

• The focal length of lens exceeds the flash coverage.
  → Check the flash coverage you set. This flash unit has the flash coverage between 28 and 105mm, which fits medium-format cameras.

Firmware Upgrade

1. This product supports firmware upgrade through the USB-C port, please use USB-C cable (sold separately).
2. As the firmware upgrade needs the support of Godox G3 software, please download and install the “Godox G3 firmware upgrade software” before upgrading. Then, choose the related firmware file.
3. Please refer to the latest electronic version of the instruction manual.

Compatible Camera Models

This flash unit can be used on the following Sony camera models:

α77II, α99, α77, DSC-RX10, α6000, α7R, α6400, α7RII, α7RIII, α7M3, α9, α7RIV, α7R5, α7MIV, ZV-E10, α58, ILCE6000L, α7R3, α 350

Note:

1. This table only lists the tested camera models, not all Sony cameras. For the compatibility of other camera models, a self-test is recommended.
2. Rights to modify this table are retained.

Maintenance

• Shut down the device immediately should abnormal operation be detected. Avoid sudden impacts and the product should be dedusted regularly.
• It is normal for the flash tube to be warm when in use. Avoid continuous flashes if unnecessary.
• Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories.
• This product, except consumables e.g. flash tube, is supported with a one-year warranty.
• Unauthorized service will void the warranty.
• If the product had failures or was wetted, do not use it until it is repaired by professionals.
• Changes made to the specifications or designs may not be reflected in this manual.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

Warning

Operating frequency: 2403MHz-2483.0MHz
Maximum EIRP Power: -10.82dBm

Declaration of Conformity
GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment are in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states.

For more information of DoC, Please click this web link: https://www.godox.com/eu-declaration-of-conformity/
The device complies with RF specifications when the device used at 0mm from your body.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you!

Product Information| Model
Name| Product Code Number
Contact Number
---|---|---
Customer Information| Address
Name
Seller Information| Contact Number
Address
Date of Sale
Note|

Note: This form shall be sealed by the seller.

Applicable Products

The document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items, giveaways and additional accessories attached, etc.) are not included in this warranty scope.

Warranty Period

The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases

The guarantee and service offered by this document are not applicable in the following cases: (1) The product or accessory has expired its warranty period; (2) Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc; (3) Breakage or damage caused by non- authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment; (4) The original identifying information of product or accessory is modified, alternated, or removed; (5) No valid warranty card; (6) Breakage or damage caused by using illegally authorized, nonstandard or non-public released software; (7) Breakage or damage caused by force majeure or accident; (8) Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information

The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Product Type| Name| Maintenance Period(month)| Warranty Service Type
---|---|---|---
Parts| Circuit board|

12

| Customer sends the product to designated site
Battery|

3

| Customer sends the product to designated site
Electrical parts e.g. battery charger, etc.|

12

| Customer sends the product to designated site
Other Items| Power cord, sync cable, lamp body, lamp cover, locking device, package, etc.|

No

| Without warranty

Godox After-sale Service   Call   +86-755-29609320(8062)

Wechat
Official Account

GODOX Photo Equipment Co.,Ltd.
Add.: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street,
Bao’an District, Shenzhen 518103, China   Tel: +86-755-29609320(8062)
Fax: +86-755-25723423   E-mail: godox@godox.com

www.godox.com
Made in China | 705-V1PRS0-00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>